DOI QR코드

DOI QR Code

Cyclic behavior of RT-cement treated marine clay subjected to low and high loading frequencies

  • Al-Bared, Mohammed A.M. (Department of Civil and Environmental Engineering, Universiti Teknologi PETRONAS) ;
  • Harahap, Indra S.H. (Department of Civil and Environmental Engineering, Universiti Teknologi PETRONAS) ;
  • Marto, Aminaton (Malaysia-Japan International Institute of Technology, Universiti Teknologi Malaysia (UTM) Kuala Lumpur) ;
  • Mohamad, Hisham (Department of Civil and Environmental Engineering, Universiti Teknologi PETRONAS) ;
  • Abad, Seyed Vahid Alavi Nezhad Khalil (Department of Civil Engineering, Birjand University of Technology) ;
  • Mustaffa, Zahiraniza (Department of Civil and Environmental Engineering, Universiti Teknologi PETRONAS)
  • Received : 2020.02.10
  • Accepted : 2020.04.16
  • Published : 2020.06.10

Abstract

The weakening and softening behavior of soft clay subjected to cyclic loading due to the build-up of excess pore water pressure is well-known. During the design stage of the foundation of highways and coastal high-rise buildings, it is important to study the mechanical behavior of marine soils under cyclic loading as they undergo greater settlement during cyclic loading than under static loading. Therefore, this research evaluates the cyclic stress-strain and shear strength of untreated and treated marine clay under the effects of wind, earthquake, and traffic loadings. A series of laboratory stress-controlled cyclic triaxial tests have been conducted on both untreated and treated marine clay using different effective confining pressures and a frequency of 0.5 and 1.0 Hz. In addition, treated samples were cured for 28 and 90 days and tested under a frequency of 2.0 Hz. The results revealed significant differences in the performance of treated marine clay samples than that of untreated samples under cyclic loading. The treated marine clay samples were able to stand up to 2000 loading cycles before failure, while untreated marine clay samples could not stand few loading cycles. The untreated marine clay displayed a higher permanent axial strain rate under cyclic loading than the treated clay due to the existence of new cementing compounds after the treatment with recycled tiles and low amount (2%) of cement. The effect of the effective confining pressure was found to be significant on untreated marine clay while its effect was not crucial for the treated samples cured for 90 days. Treated samples cured for 90 days performed better under cyclic loading than the ones cured for 28 days and this is due to the higher amount of cementitious compounds formed with time. The highest deformation was found at 0.5 Hz, which cannot be considered as a critical frequency since smaller frequencies were not used. Therefore, it is recommended to consider testing the treated marine clay using smaller frequencies than 0.5 Hz.

Keywords

Acknowledgement

The authors acknowledge the generous financial support provided by Universiti Teknologi PETRONAS (UTP) using the Graduate Assistantship Scheme (GA). The authors would like to express their gratitude and appreciation to UTP for the generous support. The authors also acknowledge Universiti Teknologi Malaysia (UTM) for the access to the geotechnical laboratory to conduct some of the tests.

References

  1. Ahmed, A. (2015), "Compressive strength and microstructure of soft clay soil stabilized with recycled bassanite", Appl. Clay Sci., 104, 27-35. https://doi.org/10.1016/j.clay.2014.11.031.
  2. Al-Bared, M.A.M. and Marto, A. (2017a), "Review on the geotechnical and engineering properties of marine clay and the suitable common stabilization methods", Proceedings of the 2nd International Conference on Separation Technology, Johor, Malaysia, April.
  3. Al-Bared, M.A.M. and Marto, A. (2017b), "A review on the geotechnical and engineering characteristics of marine clay and the modern methods of improvements", Malaysian J. Fundam. Appl. Sci., 13(4), 825-831. https://doi.org/10.11113/mjfas.v13n4.921
  4. Al-bared, M.A.M., Harahap, I.S.H. and Marto, A. (2018), "Sustainable strength improvement of soft clay stabilized with two sizes of recycled additive", Int. J. GEOMATE, 15(51), 39-46. https://doi.org/10.21660/2018.51.06065.
  5. Al-Bared, M.A.M., Harahap, I.S.H., Marto, A., Alavi Nezhad Khalil Abad, S.V., Mustaffa, Z. and Ali, M.O.A. (2019a), "Undrained shear strength and microstructural characterization of treated soft soil with recycled materials", Geomech. Eng., 18(4), 427-437. https://doi.org/10.12989/gae.2019.18.4.427.
  6. Al-Bared, M.A.M., Harahap, I.S.H., Marto, A., Alavi Nezhad Khalil Abad, S.V., Mustaffa, Z. and Ali, M.O.A. (2019b), "Mechanical behaviour of waste powdered tiles and Portland cement treated soft clay", Geomech. Eng., 19(1), 37-47. https://doi.org/10.12989/gae.2019.19.1.037.
  7. Al-Bared, M.A.M., Marto, A., Harahap, I.S.H. and Kasim, F. (2018a), "Compaction and plasticity comparative behaviour of soft clay treated with coarse and fine sizes of ceramic tiles", E3S Web Conf. 34, 1-9. https://doi.org/10.1051/e3sconf/20183401012.
  8. Al-Bared, M.A.M., Marto, A., Latifi, N. and Horpibulsuk, S. (2018b), "Sustainable improvement of marine clay using recycled blended tiles", Geotech. Geol. Eng., 36, 3135-3147. https://doi.org/10.1007/s10706-018-0525-8.
  9. Andersen, K.H. (2004), "Cyclic clay data for foundation design of structures subjected to wave loading", Proceedings of the International Conference on Cyclic Behaviour of Soils and Liquefaction Phenomena, Bochum, Germany, March-April.
  10. Andersen, K.H. (2009), "Bearing capacity under cyclic loading-offshore, along the coast, and on land", Can. Geotech. J., 46(5), 513-535. https://doi.org/10.1139/T09-003.
  11. Andersen, K.H. and Lauritzsen, R. (1988), "Bearing capacity for foundations under cyclic loads", J. Geotech. Eng., 114(5), 540-555. https://doi.org/10.1061/(ASCE)0733-9410(1988)114:5(540).
  12. Andersen, K.H., Brown, S.F., Foss, I., Pool, J.H. and Rosenbrand, W.F. (1976), "Effect of cyclic loading on clay behavior", Proceedings of the Conference on Design and Construction of Offshore Structures, London, U.K., October.
  13. Ashango, A.A. and Patra, N.R. (2014), "Static and cyclic properties of clay subgrade stabilised with rice husk ash and Portland slag cement", Int. J. Pavement Eng., 15(10), 906-916. https://doi.org/10.1080/10298436.2014.893323.
  14. ASTM (1996), ASTM D5311/D5311M-13 Standard Test Method for Load Controlled Cyclic Triaxial Strength of Soil.
  15. ASTM (2014), D3999/D3999M -11 Standard Test Methods for the Determination of the Modulus and Damping Properties of Soils Using the Cyclic Triaxial Apparatus.
  16. Ayub, A., Mohd Yunus, N., Hezmi, M., Ali, N. and Jamaluddin, N. (2018), "Strength development of marine clay treated by demolished concrete materials with morphological identifications", J. Phys. Conf. Ser., 1049, 1-12. https://doi.org/10.1088/1742-6596/1049/1/012032.
  17. Bray, J.D. and Sancio, R.B. (2006), "Assessment of the liquefaction susceptibility of fine-grained soils", J. Geotech. Geoenviron. Eng., 132(9), 1165-1177. https://doi.org/10.1061/(ASCE)1090-0241(2006)132:9(1165).
  18. Bushra, I. and Robinson, R.G. (2012), "Shear strength behavior of cement treated marine clay", Int. J. Geotech. Eng., 6(4), 455-465. https://doi.org/10.3328/IJGE.2012.06.04.455-465.
  19. Chang, I. and Cho, G.C. (2019), "Shear strength behavior and parameters of microbial gellan gum-treated soils: from sand to clay", Acta Geotech., 14(2), 361-375. https://doi.org/10.1007/s11440-018-0641-x.
  20. Chang, I., Im, J., Lee, S.W. and Cho, G.C. (2017), "Strength durability of gellan gum biopolymer-treated Korean sand with cyclic wetting and drying", Constr. Build. Mater., 143, 210-221. https://doi.org/10.1016/j.conbuildmat.2017.02.061.
  21. Chang, I., Im, J., Prasidhi, A.K. and Cho, G.C. (2015), "Effects of Xanthan gum biopolymer on soil strengthening", Constr. Build. Mater., 74, 65-72. https://doi.org/10.1016/j.conbuildmat.2014.10.026.
  22. Chen, X.L., Li, D. and Liu, R.M. (2012), "Effects of vibration frequency on dynamic properties of undisturbed structural marine soil", Appl. Mech. Mater., 193, 925-930. https://doi.org/10.4028/www.scientific.net/AMM.193-194.925.
  23. Damoerin, D., Prakoso, W.A. and Utami, Y. (2015), "Improving shear strength of clay by using cement column reinforcement under consolidated undrained test", Int. J. Technol., 6(4), 709-717. https://doi.org/10.14716/ijtech.v6i4.1206.
  24. Gu, C., Wang, J., Cai, Y. and Guo, L. (2014), "Influence of cyclic loading history on small strain shear modulus of saturated clays", Soil Dyn. Earthq. Eng., 66, 1-12. https://doi.org/10.1016/j.soildyn.2014.06.027.
  25. Hyde, A.F.L. and Ward, S.J. (1985), "A pore pressure and stability model for a silty clay under repeated loading", Geotechnique, 35(2), 113-125. https://doi.org/10.1680/geot.1985.35.2.113.
  26. Hyde, A.F.L., Yasuhara, K. and Hirao, K. (1993), "Stability criteria for marine clay under one-way cyclic loading", J. Geotech. Eng., 119(11), 1771-1789. https://doi.org/10.1061/(ASCE)0733-9410(1993)119:11(1771).
  27. Ikeagwuani, C.C., Nwonu, D.C., Eze, C. and Onuoha, I. (2017), "Investigation of shear strength parameters and effect of different compactive effort on lateritic soil stabilized with coconut husk ash and lime", Niger. J. Technol., 36(4), 1016-1021. http://doi.org/10.4314/njt.v36i4.4.
  28. Ishihara, I. (1996), Soil Behavior in Earthquake Geotechnics, Clarendon Press, Oxford, U.K.
  29. Jin, L.J., Mohd Yunus, N.Z., Hezmi, M.A., Rashid, A.S.A., Marto, A., Kalatehjari, R., Pakir, F., Mashros, N. and Ganiyu, A.A. (2018), "Predicting the effective depth of soil stabilization for marine clay treated by biomass silica", KSCE J. Civ. Eng., 22(11), 4316-4326. https://doi.org/10.1007/s12205-018-1294-x.
  30. Jitsangiam, P., Nusit, K. and Nikraz, H. (2018), "Flexural modulus of cement-stabilized materials for the mechanistic pavement design approach", Proceedings of the GeoShanghai 2018 International Conference: Transportation Geotechnics and Pavement Engineering, Shanghai, China, May.
  31. Jitsangiam, P., Nusit, K., Chummuneerat, S., Chindaprasirt, P. and Pichayapan, P. (2016), "Fatigue assessment of cement-treated base for roads: An examination of beam-fatigue tests", J. Mater. Civ. Eng., 28(10), 04016095. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001601.
  32. Kamruzzaman, A.H.M., Chew, S.H. and Lee, F.H. (2009), "Structuration and destructuration behavior of cement-treated Singapore marine clay", J. Geotech. Geoenviron. Eng., 135(4), 573-589. https://doi.org/10.1061/(ASCE)1090-0241(2009)135:4(573).
  33. Kaya, Z. and Erken, A. (2015), "Cyclic and post-cyclic monotonic behavior of Adapazari soils", Soil Dyn. Earthq. Eng., 77, 83-96. https://doi.org/10.1016/j.soildyn.2015.05.003.
  34. Kim, A.R., Chang, I., Cho, G.C. and Shim, S.H. (2018), "Strength and dynamic properties of cement-mixed Korean marine clays", KSCE J. Civ. Eng., 22, 1150-1161. https://doi.org/10.1007/s12205-017-1686-3.
  35. Kucharczyk, K., Gluchowski, A., Miturski, M. and Sas, W. (2018), "Influence of load frequency on cohesive soil respond", Geosciences, 8(12), 1-13. https://doi.org/10.3390/geosciences8120468.
  36. Lee, K.L. and Jr, J.A.F. (2008), "Strength of clay subjected to cyclic loading", Mar. Geotechnol., 1(3), 165-185. https://doi.org/10.1080/10641197609388162.
  37. Lei, H., Liu, J., Liu, M., Zhang, Z. and Jiang, M. (2016), "Effects of frequency and cyclic stress ratio on creep behavior of clay under cyclic loading", Mar. Georesour. Geotechnol., 35(2), 281-291. https://doi.org/10.1080/1064119X.2016.1157659.
  38. Marto, A. (1998), "Pore pressure response of undrained two-way cyclic loading of silt", J. Civ. Eng., 11(1), 35-63.
  39. Marto, A., Mohd Yunus, N.Z., Pakir, F., Latifi, N., Mat Nor, A.H. and Tan, C.S. (2014), "Stabilization of marine clay by biomass silica (Non-traditional) stabilizers", Appl. Mech. Mater., 695, 93-97. https://doi.org/10.4028/www.scientific.net/amm.695.93.
  40. Metcalfe, I. (2013), "Tectonic evolution of the Malay Peninsula", J. Asian Earth Sci., 76, 195-213. https://doi.org/10.1016/j.jseaes.2012.12.011.
  41. Mohd Akip Tan, S.N., Mohamad, E.T., Saad, R. and Nordiana, M.M. (2014), "Assessment of subsurface profile at silc, Nusajaya by 2d resistivity method", Appl. Mech. Mater., 695, 823-827. https://doi.org/10.4028/www.scientific.net/amm.695.823.
  42. Moses, G.G. and Rao, S.N. (2007), "Behavior of marine clay subjected to cyclic loading with sustained shear stress", Mar. Georesour. Geotechnol., 25(2), 81-96. https://doi.org/10.1080/10641190701334198.
  43. Moses, G.G., Rao, S.N. and Rao, P.N. (2003), "Undrained strength behaviour of a cemented marine clay under monotonic and cyclic loading", Ocean Eng., 30(14), 1765-1789. https://doi.org/10.1016/S0029-8018(03)00018-0.
  44. Nusit, K. and Jitsangiam, P. (2016), "Damage behavior of cement treated base material", Procedia Eng., 143, 161-169. https://doi.org/10.1016/j.proeng.2016.06.021.
  45. Nusit, K., Jitsangiam, P., Kodikara, J. and Bui, H. (2015b), "Cyclic loading responses of cement - stabilised base materials: An investigation on moduli for pavement design", Proceedings of the 12th Australia New Zealand Conference on Geomechanics, Wellington, New Zealand, February.
  46. Nusit, K., Jitsangiam, P., Kodikara, J., Bui, H.H. and Leung, G.L.M. (2015a), "Dynamic modulus measurements of bound cement-treated base materials", Geotech. Test. J., 38(3), 275-289. https://doi.org/10.1520/GTJ20140233.
  47. Nusit, K., Jitsangiam, P., Kodikara, J., Bui, H.H. and Leung, G.L.M. (2016), "Advanced characteristics of cement-treated materials with respect to strength performance and damage evolution", J. Mater. Civ. Eng., 29(4), 04016255. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001772.
  48. Saglam, S. and Bakir, B.S. (2014), "Cyclic response of saturated silts", Soil Dyn. Earthq. Eng., 61-62, 164-175. https://doi.org/10.1016/j.soildyn.2014.02.011.
  49. Shoushtari, AV., Adnan, A. and Zare, M. (2019), "Incorporating the local faults effects in development of seismic ground-motion hazard mapping for the Peninsular Malaysia region", J. Asian Earth Sci., 163(C), 194-211. https://doi.org/10.1016/j.jseaes.2018.06.010.
  50. Soralump, S. and Prasomsri, J. (2016), "Cyclic pore water pressure generation and stiffness degradation in compacted clays", J. Geotech. Geoenviron. Eng., 142(1), 04015060. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001364.
  51. Vucetic, M. and Dobry, R. (1988), "Degradation of marine clays under cyclic loading", J. Geotech. Eng., 114(2), 133-149. https://doi.org/10.1061/(ASCE)0733-9410(1988)114:2(133).
  52. Wang, J., Cai, Y. and Yang, F. (2013a), "Effects of initial shear stress on cyclic behavior of saturated soft clay", Mar. Georesour. Geotechnol., 31(1), 86-106. https://doi.org/10.1080/1064119X.2012.676153.
  53. Wang, J., Guo, L., Cai, Y., Xu, C. and Gu, C. (2013b), "Strain and pore pressure development on soft marine clay in triaxial tests with a large number of cycles", Ocean Eng., 74, 125-132. https://doi.org/10.1016/j.oceaneng.2013.10.005.
  54. Wang, M., Kong, L., Zhao, C. and Zang, M. (2012), "Dynamic characteristics of lime-treated expansive soil under cyclic loading", J. Rock Mech. Geotech. Eng., 4(4), 352-359 https://doi.org/10.3724/sp.j.1235.2012.00352.
  55. Wang, Y., Gao, Y., Li, B., Fang, H., Wang, F., Guo, L. and Zhang, F. (2017a), "One-way cyclic deformation behavior of natural soft clay under continuous principal stress rotation", Soils Found., 57(6), 1002-1013. https://doi.org/10.1016/j.sandf.2017.08.027.
  56. Wang, Y., Wu, D., Qiu, Y. and Wang, D. (2017b), "Experimental investigation on cyclic deformation behavior of soft marine clay involved principal stress rotation", Mar. Georesour. Geotechnol., 35(4), 571-577. https://doi.org/10.1080/1064119X.2016.1194922.
  57. Wichtmann, T. and Triantafyllidis, T. (2015), "Stress attractors predicted by a high-cycle accumulation model confirmed by undrained cyclic triaxial tests", Soil Dyn. Earthq. Eng., 69, 125-137. https://doi.org/10.1016/j.soildyn.2014.10.013.
  58. Wichtmann, T., Andersen, K.H., Sjursen, M.A. and Berre, T. (2013), "Cyclic tests on high-quality undisturbed block samples of soft marine Norwegian clay", Can. Geotech. J., 50(4), 400-412. https://doi.org/10.1139/cgj-2011-0390.
  59. Wichtmann, T., Niemunis, A. and Triantafyllidis, T. (2005), "Strain accumulation in sand due to cyclic loading: drained triaxial tests", Soil Dyn. Earthq. Eng., 25(12), 967-979. https://doi.org/10.1016/j.soildyn.2005.02.022.
  60. Xu, X., Li, Q. and Xu, G. (2019), "Investigation on the behavior of frozen silty clay subjected to monotonic and cyclic triaxial loading", Acta Geotech., 6, 22-24. https://doi.org/10.1007/s11440-019-00826-6.
  61. Yasuhara, K., Yamanouchi, T. and Hirao, K. (2017), "Cyclic strength and deformation of normally consolidated clay", Soils Found., 22(3), 77-91. https://doi.org/10.3208/sandf1972.22.3.
  62. Zainuddin, N., Mohd Yunus, N.Z., Al-Bared, M.A.M., Marto, A., Harahap, I.S.H. and Rashid, A.S.A. (2019), "Measuring the engineering properties of marine clay treated with disposed granite waste", Measurement, 131, 50-60. https://doi.org/10.1016/j.measurement.2018.08.053.
  63. Zhang, Z., Wang, T., Wu, S., Tang, H. and Liang, C. (2018a), "Dynamics characteristic of red clay in a deep-seated landslide, Northwest China: An experiment study", Eng. Geol., 239, 254-268. https://doi.org/10.1016/j.enggeo.2018.04.005.
  64. Zhang, Z., Wang, T., Wu, S., Tang, H., Xin, P. and Liang, C. (2017), "Dynamics stress-strain behavior of Tianshui soils", Landslides, 14(1), 323-335. https://doi.org/10.1007/s10346-016-0694-6.

Cited by

  1. Mechanical properties and microstructures of stabilised dredged expansive soil from coal mine vol.25, pp.2, 2020, https://doi.org/10.12989/gae.2021.25.2.143
  2. Experimental Study on Endurance Performance of Lime and Cement-Treated Cohesive Soil vol.25, pp.9, 2021, https://doi.org/10.1007/s12205-021-2154-7
  3. Physio-Chemical Properties, Consolidation, and Stabilization of Tropical Peat Soil Using Traditional Soil Additives - A State of the Art Literature Review vol.25, pp.10, 2021, https://doi.org/10.1007/s12205-021-1247-7
  4. Performance of a Composite Soil Prepared with Red Mud and Desulfurized Gypsum vol.26, pp.1, 2020, https://doi.org/10.1007/s12205-021-2054-x