• Journal of Power Electronics
• /
• 제17권3호
• /
• pp.601-609
• /
• 2017

Gallium nitride (GaN) power switching devices are promising candidates for high switching frequency and high efficiency power conversion due to their fast switching, low on-state resistance, and high-temperature operation capability. In order to facilitate the use of these new devices better, it is required to investigate the device characteristics and performance in detail preferably by comparing with various conventional silicon (Si) devices. This paper presents a comprehensive study of GaN high electron mobility transistor (HEMT) based non-isolated point-of-load (POL) synchronous buck converter operating at 2.7 MHz with a high step-down ratio (24 V to 3.3 V). The characteristics and performance of GaN HEMT and three different Si devices are analytically investigated and the optimal operating point for GaN HEMT is discussed. Zero-voltage switching (ZVS) is implemented to minimize switching loss in high switching frequency operation. The prototype circuit and experimental data support the validity of analytical and simulation results.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2014년도 전력전자학술대회 논문집
• /
• pp.431-432
• /
• 2014

Recently, the demand of LED(light-emitting diode) lighting is gradually enlarged by governmental saveenergy policy, which the LED lighting has been established compulsorily in new buildings, public institutions, and residential installations etc.. The LED lighting is driven by SMPS (switching mode power supply). The SMPS requires high efficiency because the SMPS changes a commercial ac power source to low voltage dc power source. Harmonic components that occur in the conversion process of SMPS decrease system power factor and deal great damage in electric power system. To improve such problems, this paper proposes a SMPS of high efficiency. The switching devices in the proposed SMPS are operated by soft switching technique using a new quasi-resonant circuit. The input ac current waveform in the proposed SMPS becomes a quasi-sinusoidal waveform proportional to the magnitude of input ac voltage under constant switching frequency. As a result, the proposed SMPS obtains low switching power loss and high efficiency, and its input power factor is nearly in unity.

• Journal of Power Electronics
• /
• 제17권6호
• /
• pp.1433-1444
• /
• 2017

A family of non-isolated DC-DC three-port converters (TPCs) that allows for a more flexible power flow among a renewable energy source, an energy storage device and a current-reversible DC bus is introduced. Most of the reported non-isolated topologies in this area consider only a power consuming load. However, for applications such as hybrid-electric vehicle braking systems and DC microgrids, the load power generating capability should also be considered. The proposed three-port family consists of one unidirectional port and two bi-directional ports. Hence, they are well-suited for photovoltaic (PV)-battery-DC bus systems from the power flow viewpoint. Three-port converters are derived by combining different commonly known power converters in an integrated manner while considering the voltage polarity, voltage levels among the ports and the overall voltage conversion ratio. The derived converter topologies are able to allow for seven different modes of operation among the sources and load. A three-port converter which integrates a boost converter with a buck converter is used as a design example. Extensions of these topologies by combining the soft-switching technique with the proposed design example are also presented. Experiment results are given to verify the proposed three-port converter family and its analysis.

• Journal of Multimedia Information System
• /
• 제9권3호
• /
• pp.177-182
• /
• 2022

A deep neural network (DNN) includes variables whose values keep on changing with the training process until it reaches the final point of convergence. These variables are the co-efficient of a polynomial expression to relate to the feature extraction process. In general, DNNs work in multiple 'dimensions' depending upon the number of channels and batches accounted for training. However, after the execution of feature extraction and before entering the SoftMax or other classifier, there is a conversion of features from multiple N-dimensions to a single vector form, where 'N' represents the number of activation channels. This usually happens in a Fully connected layer (FCL) or a dense layer. This reduced 2D feature is the subject of study for our analysis. For this, we have used the FCL, so the trained weights of this FCL will be used for the weight-class correlation analysis. The popular DNN models selected for our study are ResNet-101, VGG-19, and GoogleNet. These models' weights are directly used for fine-tuning (with all trained weights initially transferred) and scratch trained (with no weights transferred). Then the comparison is done by plotting the graph of feature distribution and the final FCL weights.

• 한국컴퓨터산업학회논문지
• /
• 제8권2호
• /
• pp.107-112
• /
• 2007

피부과용 레이저 파장은 아주 얇은층의 조직두께에서 물의 흡수가 거의 90%이상 일어나는데 병소의 표피나 조직은 거의 물로 구성되어 흡수로 인해 증발효과를 가질 수가 있다. 표피를 절개, 층별로 증발 시킬 수 있으며 조직의 정확한 절개가 가능하다. 혈관이나 림프시스템에도 봉합수술이 가능하고 수술부위가 건조하고 눈으로 볼수 있고 무출혈 수술이 가능하다. 특히, 펄스에 대한 튜브양단 출력의 안정이 매우 중요함으로, 본 연구에서는 고주파 방식의 전력변환 장치를 사용하여 부피를 줄이고 의료용 레이저의 전류파형을 쉽게 제어할 수 있어 다양한 치료 효과를 낼 수 있다. ZVS(Zero Voltage Switching)나 ZVZCS(Zero Voltage and Zero Current Switching)를 도입하면 스위칭 손실을 줄일 수 있어 더욱 유리하다. 제안된 의료용 레이저의 전력부에는 1차측 도움에 의한 ZVZCS기법을 도입하여 넓은 부하 범위에서 안정된 soft-switching을 할 수가 있고 제어부는 microcontroller를 구성하여 출력전류 파형을 사용자가 임의의 형태를 갖도록 하였다. 설계 및 제작하여 실험한 결과, 기존장비에 비해 20%의 향상된 결과를 가져왔고, 추후 시스템적으로 보완을 하면 우수한 결과가 될 것으로 사려된다.

• 한국근적외분광분석학회:학술대회논문집
• /
• 한국근적외분광분석학회 2001년도 NIR-2001
• /
• pp.1257-1257
• /
• 2001

Fourier transform near infrared (FT-NIR) spectroscopy was used as a rapid method to measure the $^{o}Brix$ content and to discriminate between different must samples in terms of their fee amino nitrogen (FAN) values. FT-NIR spectroscopy was also used as a rapid method to discriminate between Chardonnay wine samples in terms of the status of the male-lactic fermentation (MLF). This was done by monitoring the conversion of malic to lactic acid and thereby determining whether MLF has started, is underway or has been completed followed by classification of the samples. Furthermore, FT-NIR spectroscopy was applied as a rapid method to discriminate between table wine samples in terms of the ethyl carbamate (EC) content. EC in wine can pose a health threat and need to be monitored by determining the EC content in relation to the regulatory limits set by the authorities. For each of the above mentioned parameters, $QUANT+^{TM}$ methods were built and calibrations derived and it was found that a very strong correlation existed in the sample set for the FT-NIR spectroscopic predictions of $^{o}Brix$ (r = 0.99, SECV = 0.306), but the correlations for the FAN (r = 0.61, SECV = 272.1), malic acid (r = 0.58, SECV = 1.06), lactic acid (r = 0.51, SECV = 1.14) and EC predictions (r = 0.47, SECV = 3.67) were not as good. Soft Independent Modeling by Class Analogy (SIMCA) diagnostics and validation was applied as a sophisticated discrimination method. The must samples could be classified in terms of their FAN values when SIMCA was applied, obtaining results with recognition rates exceeding 80%. When SIMCA diagnostics and validation were applied to determine the progress of conversion of malic to lactic acid and the EC content, again results with recognition rates exceeding 80% were obtained. The evaluation of the applicability of FT-NIR spectroscopy measurement of FAN, $^{o}Brix$ values, malic acid, lactic acid and EC content in must and wine shows considerable promise. FT-NIR spectroscopy has the potential to reduce the analytical times considerably in a range of measurements commonly used during the wine making process. Where conventional FT-NIR calibrations are not effective, SIMCA methods can be used as a discriminative method for rapid classification of samples. SIMCA can replace expensive, time-consuming, quantitative analytical methods, if not completely, at least to some extent, because in many processes it is only needed to know whether a specific cut off point has been reach or not or whether a sample belongs to a certain class or not.

• 한국의학물리학회지:의학물리
• /
• 제15권1호
• /
• pp.23-29
• /
• 2004

CT관전압 및 기종의 변화에 따른 전자밀도 환산곡선 값의 변화가 상용 전산화치료계획장치의 선량계산 결과에 미치는 영향을 고찰하였다. CT기종 및 관전압을 달리하며 전자밀도 환산용 팬톰에 대한 CT 영상을 얻어서 여러 조직등가물질에 대해 전자밀도와 CT수의 관계를 구하였다. 동일 전자밀도에 대해 관전압이 감소함에 따라 고밀도의 골조직으로 갈수록 큰 CT수를 보였으며, 연조직에서는 거의 차이가 없었다. 전자밀도 환산곡선 값의 변화가 선량계산 결과에 미치는 정도를 알아보기 위하여 치료계획장치 상에서 폐조직과 골조직을 포함하는 물 팬톰을 그려서 만들고, 이들 가상 조직의 후방 위치에서 6 MV 광자선에 의한 선량을 계산하였다. 그 결과 폐조직, 물, 골조직의 순서로 선량이 높았으며, 골조직에 의한 선량은 관전압이 낮을수록 높은 값을 보였고, 이는 10 MV의 경우에도 동일하였다. 임상 적용의 예로서 폐 및 골반 부위의 CT 영상을 이용한 선량계산에서는 6 MV 및 10 MV모두 전자밀도 환산곡선 값의 변화에 따른 차이는 없었으며, 전자밀도 환산곡선을 구하는데 이용한 CT 기기와 선량을 계산하는데 이용한 영상을 얻은 CT 기기가 다른 데서 오는 것으로 판단되는 오차로서 최대 1.5%의 상대선량차이를 보였다.

• 한국환경농학회지
• /
• 제42권3호
• /
• pp.203-210
• /
• 2023

Ferimzone Z is a fungicide for effectively controlling rice blast. Under light irradiation conditions, it undergoes a rapid conversion to its E-stereoisomer. Given the importance of isomers in risk assessments of residues in crops, an analytical method was developed for individual isomer quantification. A comparative analysis performed using two columns in HPLC-MS/MS demonstrated that the isomers were successfully separated using the Cadenza column. For the brown rice sample preparation, 5 g of the homogenized sample was saturated with 7 mL of water. The sample was then extracted with a 10 mL mixed solvent of acetonitrile and ethyl acetate (1:1, v/v) that contained 0.1% formic acid, and it was subsequently partitioned with magnesium sulfate and sodium chloride. The upper layer was purified using dSPE containing C₁₈ and PSA sorbents. The established method was subjected to method validation, and it showed recovery rates of 90.6-98.8% (RSD ≤ 3.9%) at concentrations of 0.01, 0.1, 2 mg/kg, with a soft matrix effect (%ME) ranging from -3.1% to +6.5%. This method can be employed in monitoring studies of brown rice to determine the conversion ratio from the Z isomers to the E isomers.

• Journal of Gastric Cancer
• /
• 제12권4호
• /
• pp.237-242
• /
• 2012

Purpose: Despite the great advances in laparoscopic techniques, most active general surgeons do not apply laparoscopic surgery in the treatment of duodenal ulcer perforation when facing a real-life emergency. Therefore, our study was designed to evaluate the feasibility of laparoscopic surgery in duodenal ulcer perforation, and provide a step-by-step protocol with tips and recommendations for less experienced surgeons. Materials and Methods: Between March, 2011 and May, 2012, 21 patients presenting with duodenal ulcer perforation underwent laparoscopic primary repair with omentopexy. There were no contraindications to perform laparoscopic surgery, and the choice of primary repair was decided according to the size of the perforation. The procedure for laparoscopic primary repair with omentopexy consisted of peritoneal lavage, primary suture, and omentopexy using a knot pusher. Results: During the operation, no conversion to open surgery or intra-operative events occurred. The median operation time was 45.0 minutes (20~80 minutes). Median day of commencement of a soft diet was day 6 (4~17 days). After surgery, the median hospital stay was 8.0 days (5~27 days). Postoperative complications occurred in one patient, which included a minor leakage. This complication was resolved by conservative management. Conclusions: Although our study was carried out on a small number of patients at a single institution, we conclude that laparoscopic primary repair can be an effective surgical method in the treatment of duodenal ulcer perforation. We believe that the detailed explanation of our procedure will help beginners to perform laparoscopic primary repair more easily.

• 한국가금학회:학술대회논문집
• /
• 한국가금학회 2004년도 제21차 정기총회 및 학술발표회
• /
• pp.93-94
• /
• 2004

The experiments was conducted to investigate the effects of dietary supplementation of feather meal and pyridoxine on the taurine content of egg yolk and performance of laying hens. Feeding trial was conducted with 900 31-wk-old Hy-Line Brown layers for 4wks. The experiment consisted of six dietary treatments: control(basal diet), feather meal(FM) 3 % diet(FM 3 %), FM 3 % + pyridoxine supplemented diet(FM 3 % + Pyridox), FM 6 % diet, FM 6 % + pyridoxine supplemented diet(FM 6% + Pyridox), Synthetic taurine 0.25 % supplemented diet(Taurine). Egg production of birds fed FM 3% was highest and those of the FM diets were also higher than those of Taurine and the control. Egg weight of Taurine was significantly lower than those of FM 3 %, FM 6 % and the control but were not significantly different from those of FM 3 % + Pyridox or FM 6 % + Pyridox. Feed intake of the control was greater than those of FM 6 %, FM 6% + Pyridox or Taurine treatment but was not significantly different from those of FM 3 % and FM 3 % + Pyridox. Feed conversion of the control was significantly higher than other treatments in which that of FM 6 % was lowest. Broken and soft egg production of Taurine was highest while that of the control was lowest among treatments. Taurine content of egg yolk significantly increased by supplementation of taurine(64.7 %). FM 6 % + pyridoxine(57 %), FM 3% + pyridoxine (32.1%) and FM 6% (16.6 %). Sensory evaluation data of Taurine has shown the highest score in most of sensory attributes. It is concluded that taurine can be enriched in egg yolk by supplementation of 6 % FM diet and pyridoxine as well as 0.25 % synthetic taurine.