• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.13 no.1
• /
• pp.13-24
• /
• 2000

Current specification prescribes that upper and lower reinforcement mat is required in the same amount to resist negative and positive moment in bridge decks. But the negative moment is much smaller than positive moment because the actual behavior of decks consists of local deflection of slab and global deflection of girder. From this study, the analysis method based on harmonic analysis and slope-deflection method was developed and verified by finite element method. The negative moment, obtained from this method, were smaller than those computed based on the KHBDC specifications as much as 40∼50% in the middle of bridge. The amount of reduction of the design negative moment was shown herein to be dependent on variable parameters as shape factor(S/L) of slab, relative stiffness ratio of girder and deck slab, and so on. This investigations indicate that the upper reinforcement mat to resist negative moment can be removed. But further experimental study is required to consider durability and serviceability. From this new design concept, the construction expense can be reduced and the problem of decreasing durability resulting from corrosion of upper reinforcement steel settled.

• Computational Structural Engineering
• /
• v.9 no.3
• /
• pp.209-216
• /
• 1996

The primary objective of this paper is to grasp many characteristics of buckling behavior of latticed spherical domes under various conditions. The Arc-Length Method proposed by E.Riks is used for the computation and evaluation of geometrically nonlinear fundamental equilibrium paths and bifurcation points. And the direction of the path after the bifurcation point is decided by means of Hosono's concept. Three different nonlinear stiffness matrices of the Slope-Deflection Method are derived for the system with rigid nodes and results of the numerical analysis are examined in regard to geometrical parameters such as slenderness ratio, half-open angle, boundary conditions, and various loading types. But in case of analytical model 2 (rigid node), the post-buckling path could not be surveyed because of Newton-Raphson iteration process being diversed on the critical point since many eigenvalues become zero simultaneously.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.12
• /
• pp.135-139
• /
• 2017

The main reason for heat accidents occurring at the after stern tube bearing (STB) is excessive local pressure caused by the deflection of the propulsion shaft due to propeller loads. The probability of a heat accident is increased by the low flexibility of the shaft system in very large crude oil carriers (VLCCs) as the engine power and shaft diameter increase and the distance decreases between the forward and after STBs. This study proposed shaft system with only an after STB and no forward STB for a flexibility acquisition method for a VLCC shaft system under hull deformation. A Hertzian contact condition was applied, which assumes a half-elliptical pressure distribution along the contact width for the calculation of the local squeeze pressure. The propeller loads, heat effect, and hull deflection under engine operating conditions are also considered. The results show that the required design criteria were satisfied by building a partial slope at the white metal, which is the material at the axial contact side in the after STB. This system could reduce building cost by simplification of the shaft system.

• Geotechnical Engineering
• /
• v.7 no.4
• /
• pp.75-88
• /
• 1991

A lot of landslides has occurred in rainy seasons beginning at June through September in Korea, where about 70 percent of the total area is mountaneous. Piles can be used as one of the most useful methods to stabilize such landslides. When a row of piles is installed in soil undergoing lateral movement such as landslides, the soil across the open space between the piles can be retained by the arching action of the soil. For the purpose to establish a reasonable design method for stabilizing piles, a method for stability analysis of the slope containing stabilizing piles is presented, using the theoretical equation of the lateral force acting on the piles in soil undergoing lateral movement. In particular, the theoretical equation is arranged by applying the coefcients of lateral force as a simple equation. And also the differential equations proposed in the previous studies for the pile-stability analysis are modified, assumming that the piles above the sliding surface shall be subjected to the lateral reaction from soil in proportion to the pile deflection. Finally, to investigate the effect of stabilizing piles against landslides, an existing landslide slope in Korea is adopted as an example.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.9 no.1
• /
• pp.79-87
• /
• 1989

The influence of anchor slope on behavior of sheet pile is analysed by results of model test. It can be seen that the larger inclination of anchor causes more causes more increases of the horizontal and vertical deflection of wall, but the bending moment is less influenced by the inclination of anchor. The negative friction against vertical settlement of wall has the yielding point at the excavation level of 0.71-0.80 H. The redistribution of earth pressure on the sheet pile with dredging must be considered by soil-arching. The zero pressure point from the toe of wall is 20% higher than that of the Free Earth Support Method. It is also observed that the angle of failure planes to major principal plane is larger than the angle of $45^{\circ}+{\phi}/2$.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.3
• /
• pp.91-105
• /
• 1992

For the analysis of multistory frames with sidesway, no adequate procedures can be found in the classical methods of structural analysis. Even well-known procedures such as the slope-deflection method and the moment distribution method may not be effective tools since those methods require a multiple of computational labor and/or yield results of approximate values. In this study, a direct method is developed and proposed for the analysis of multistory frames with sidesway, which is due to the lateral loads, asymmetry of the structure itself, or asymmetry of vertical loadings. The proposed method is to obtain simple forms of equations derived by a mathematical formulation of the moment distribution procedure combined with successive correction concept. Numerical illustrations show that the results obtained by the proposed method agree well with those by rigorous ones. Undoubtedly, this newly developed method can be applied more easily for the analysis of structural frames without joint translation as well as continuous beams.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.13 no.3
• /
• pp.45-57
• /
• 1993

In case of the analysis of continuous beams, the complexity increases greatly as the number of spans becomes large, and even the slope-deflection method or the moment distribution method is subject to restriction in its utilization. In this study, a revised exact method is developed for the analysis of continuous beams up to four spans, and a new approximate method is proposed for the multi-span continuous beams. This approximate procedure is very simple in its application and provides very satisfactory results which converge closely on the exact ones. These methods can also be used conveniently especially for drawing influence lines for the support moments of continuous beams, and their value is fully appreciated because of notable simpleness as compared with the conventional method which is mainly based on the Muller-Breslau principle.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.13 no.1
• /
• pp.25-35
• /
• 2000

The superstructure of general bridge like slab bridge and slab on girder bridge is composed of elastically supported isotropic plate. The objective of this study is to develop the new analysis method for elastically supported plate with general edge beam or girder(boundaries) under arbitrary out of plane loading. The displacement solutions for the macro-element of plate and beam are obtained by solving for the unknown interactive forces and moments at the beam or nodal line locations after satisfying equilibrium equation along the nodal line. The displacement functions for macro-elements ate proposed in single Fourier series using harmonic analysis, and the equilibrium equations of nodal line are composed by using slope-deflection method. The proposed analysis method is programmed by MS-Fortran and can be applied to all types of isotropic decks with bridge-type boundaries. Numerical examples involving elastically supported plates with various aspect ratio, loading cases, and bridge-type boundary conditions are presented to demonstrate the accuracy of this program. The major advantage of this new analysis method is the development of a simple solution algorithm, leads to obtain rapidly responses of bridge deck system. This proposed method can be used in parametric study of behavior of bridge decks.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.6
• /
• pp.113-119
• /
• 2016

In this study, the method to predict the lateral response by using strain data is presented on the steel moment frame. For this, the reliability of the proposed method by applying the example of five-story frame structure were verified. Using the strain value of columns, it predicted the lateral response of structure. It is assumed that all of four strain sensors for one column set up and the strain responses of both end of the column are utilized. The lateral response of member is calculated by using the slope deflection method. Also, using the acceleration response of the one layer, the stiffness of the rotation spring located in the supporting point is predicted. As a result, it was effective to understand the lateral displacement and acceleration responses and to predict local damage and location.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.10 no.2
• /
• pp.180-187
• /
• 2018

Corrugated bulkhead has been adopted for cargo tank bulkheads of commercial vessels such as bulk carriers, product oil carriers and chemical tankers. It is considered that corrugated bulkhead is a preferred structural solution, compared to the flat stiffened bulkhead, due to several advantages such as lower mass, easier maintenance and smaller corrosion problems. Many researches to find the optimum shape of corrugated bulkhead have been mostly carried out for bulk carriers. Compared to corrugated bulkheads of bulk carriers, ones of chemical tankers are more complicated since they are composed of transverse and longitudinal bulkheads, and they are made of higher priced materials. The purpose of this study is the development of minimum weight design method for corrugated bulkhead of chemical tankers. Evolution strategy is applied as an optimization technique. It has been verified from many researches that evolution strategy searches global optimum point prominently by using multi-individual searching technique. Multi-individual searching methods need excessive time if they connect to 3-D finite element model for repetitive structural analyses. In order to resolve this issue, 2-D beam element connected to deck and lower stool is substituted for a corrugated structure in this study. To verify the reliability of the structural responses by idealized 2-D beam model, they have been compared with ones by 3-D finite element model. In this study, optimum design for corrugated bulkhead of 30 K chemical tanker has been carried out, and the results by developed optimum design program have been compared with design data of existing ship. It is found out that optimum design is about 9% lighter than one of existing ship.