• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.350-354
• /
• 1995

The Tension Leveller of Cold Rolling Mill In POSCO performs levelling the strip in high speed line. But minor variations in operating condition of driving machines such as motor, gear box, and support bearings, a small gap-variation of supporter and strip slip by poor roll revolutions can cause serious problems in the quality of strip. In this study, firstly, A condition monitoring standard for each sensor is made through with the detail analysis of vibration and strip slip. Secondly, An automatic monitoring and diagnosing system was developed to monitor the condition of Tension Leveller, and diagnose the cause of abnormal condition. Finally, A diagnosing algorithm for abnormal condition and man-machine interface (MMI) for easy operation are developed.

• Proceedings of the KIEE Conference
• /
• 1987.07a
• /
• pp.737-741
• /
• 1987

The induction motor is represented by nonlinear equations whose parameters are changing with respect to the slip-frequency, temperature, etc. The slip-frequency is effected by unknown load which is difficult to estimate on-line. Astable vector controller is designed with direct MRAC to improve the quality of the transient response. The unknown load is considered in this speed controller design, and tested by simulation. Also a flux controller is designed and tested to reduce the audible noise in this paper.

• Steel and Composite Structures
• /
• v.44 no.1
• /
• pp.1-15
• /
• 2022

The weld quality has always been an important factor affecting the development of exposed CFT column-base joint. In this paper, a new type of exposed RCFST column-base joint is proposed, in which the high strength steel bars (USD 685) are set through the column and reinforced concrete foundation without any base plate and anchor bolts. Three specimens, the varying axial force ratio (0, 0.25 and 0.5), were tested under cyclic loadings. In addition, the bending moment capacity, energy dissipation capacity and deformation capacity of column-base joints were clarified. The experimental results indicated that the axial force ratio increases the stiffness and the bending moment and improves the energy dissipation capacity of column-base joints. This is because a large axial force can limit the slip between steel tubular and infilled concrete effectively. The specimens show stable hysteresis behavior.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.6
• /
• pp.553-561
• /
• 2011

A theoretical approach is carried out to predict the quality factors of flexible modes of a microcantilever on a squeeze-film. The frequency response function of an inertially-excited microcantilever beam is derived using an Euler-Bernoulli beam theory. The external force due to squeeze-film phenomenon is developed from the Reynolds equation. Slip boundary conditions are employed at the interfaces between the fluid and the structure to consider the gas rarefaction effect, and pressure boundary condition at both ends of fluid analysis region is enhanced to increase the exactness of predicted quality factors. To the end, an approximate equation is derived for the first bending mode of the microcantilever. Using the approximate equation, the quality factors of the second and third bending modes are calculated and compared with experimental results of previously reported work. The comparison shows the feasibility of the current approach.

• Tunnel and Underground Space
• /
• v.32 no.5
• /
• pp.312-326
• /
• 2022

The generalized Hoek-Brown (GHB) criterion, which is recognized as one of the standard failure conditions for rock mass, is specialized for rock engineering applications and covers a wide range of rock mass conditions. Accordingly, many research efforts have been devoted to the incorporation of this criterion into the stability analysis of rock structures. In this study, the slip-line analysis method, which is a kind of elastoplastic analysis method, is combined with the GHB failure criterion to derive analytical equations that can easily calculate the plastic radius and stress distribution in the vicinity of the circular tunnel. In the process of derivation of related formulas, it is assumed that the behavior of rock mass after failure is perfectly plastic and the in-situ stress condition is hydrostatic. In the formulation, it is revealed that the plastic radius can be calculated analytically using the two respective tangential friction angles corresponding to the stress conditions at tunnel wall and elastic-plastic boundary. It is also shown that the plastic radius and stress distribution calculated using the derived analytical equations coincide with the results of Lee & Pietruszczak's numerical method published in 2008. In the latter part of this paper, the influence of the quality of the rock mass on the size of the plastic zone, the stress distribution, and the change of the tangential friction angle was investigated using the derived analytical equations.

• Journal of Korean Society of Steel Construction
• /
• v.15 no.6 s.67
• /
• pp.611-620
• /
• 2003

Shear studs with a diameter of 19mm or 22mm are typically used in steel-concrete composite bridge. For the simplification of details in steel bridges, the convenience of removing concrete slab, and the efficient distribution of shear pockets for precast decks, large studs can be an excellent alternative. Through push-out tests on large stud shear connectors that transcend the limitation of current design codes, static behavior was investigated and comparisons with design equations performed. The shear stiffness of the connectors in elastic range and trilinear load-slip curves were proposed after shear tests on 25mm, 27mm, and 30mm studs. The ultimate slip capacity and ultimate strength of large studs were also evaluated, with the test results revealing conservative values for the design shear strength in Eurocode-4. For 30mm stud shear connectors, the welding quality and bearing capacity of concrete slab should be improved.

• Journal of Biosystems Engineering
• /
• v.28 no.5
• /
• pp.395-402
• /
• 2003

Standard ginseng seedling, selected after one year's rearing in the seedling bed has been conventionally transplanted in Korea. Recently, the direct seeding areas have been increasing to product high quality ginsengs for red-ginseng processing. Reciprocating push-rod brush, holed-roller and vacuum suction seeders, planting with 30 ${\times}$ 30mm spacings and adjustable to the folds were designed and theirs performances were evaluated. The developed three types of seeders reliably performed at the success rate over 95% with less than 10% in slip rate, and could be used a seeder for the greater spacings by adjusting metering parts. The research concluded that the vacuum suction seeder was the most feasible and practical with the greatest metering success and the least slip among three type seeders of the reciprocating push-rod brush, holed-roller and vacuum suction seeders. The vacuum suction seeder holds a seed with each needle nozzle using the negative pressure created by a vacuum pump. The capacity was 24.5 times greater than a man power at the speed of 5 m/min.

• Journal of The Korean Digital Architecture Interior Association
• /
• v.12 no.4
• /
• pp.39-48
• /
• 2012

Generally, rural housing in Korea have had target of people who are in good physical health rather than the disabled. Therefore, it is difficult to offer high quality residential environment for the elderly and the disabled. The purpose of this study is to present the remodeling of rural house for the disabled. this study divides the a rural house into 7 sectors : a passage to entrance, an entrance hall, a livingroom, a bedroom, a bathroom, a kitchen, and etc. this study propose the following renovation plan that rural housing to be barrier free space. First, in passage to entrance of the house, people with disabilities should not experience difficulties in walking, so installing ramps to remove the stepped slope grade without slip so that the floor finish should be. Second, install grab handle on the wall inside the housing so that the disabled can lean on the handle. Third, placing the furniture in the bedroom that wheelchair can be rotated, and make to lower the height of the switchs. Forth, install a non-slip floor tile to prevent accidents in the bathroom.

• Journal of Advanced Marine Engineering and Technology
• /
• v.41 no.4
• /
• pp.330-336
• /
• 2017

This study performs a root cause analysis of the sticking that occurs in the hydraulically actuated wet type multi-disc friction clutch in a ship's diesel engine propulsion system that uses rubber elastic coupling. The fishbone method was used to study the sticking through dismantling investigation of the reduction gear and clutch, investigation of the components, and onboard system tests including nondestructive testing. The friction plate sticking is caused by the slip due to friction heat resulting from the leakage of control oil through cracks in the assembled hollow shaft. The friction plate cooling oil also leaks simultaneously through the crack, and partial sticking occurs due to the hot spots in the friction plates. These are caused by insufficient amount of cooling oil due to oil leakage.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.31.3-31
• /
• 2001

In this paper, an automatic pipe-cutting machine that uses magnet to attach itself to pipe and performs unmanned cutting process is proposed. The machine uses magnetic force to prevent slip and to attach the machine to the pipe against gravity. The magnetic force is adjustable by changing the gap between the magnet and the pipe. During pipe cutting process, the gravity acting on the pipe-cutting machine widely varies nonlinearly where the gravity is function of climbing angle of the cutting machine along the pipe. The cutting quality is deteriorated with irregular cutting speed. It is necessary to maintain constant cutting speed to obtain good cutting quality ...