• Computers and Concrete
• /
• 제19권4호
• /
• pp.375-385
• /
• 2017

In the present paper experimental and numerical analysis of hook-ended steel fiber reinforced concrete is carried out. The experimental tests are performed on notched beams loaded in 3-point bending using fiber volume fractions up to 1.5%. The numerical analysis of fiber reinforced concrete beams is performed at meso scale. The concrete is discretized with 3D solid finite elements and microplane model is used as a constitutive law. The fibers are modelled by randomly generated 1D truss finite elements, which are connected with concrete matrix by discrete bond-slip relationship. It is demonstrated that the presented approach, which is based on the modelling of concrete matrix using microplane model, able to realistically replicate experimental results. In all investigated cases failure is due to the pull-out of fibers. It is shown that with increase of volume content of fibers the effective bond strength and slip capacity of fibers decreases.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 1998년도 추계 학술발표회 논문집 Proceedings of EESK Conference-Spring 1998
• /
• pp.57-64
• /
• 1998

This paper presents the cyclic seismic performance of slip-critically designed, high-strength bolted-beam splice in steel moment frame. Before the moment connection reaching its plastic strength, unexpected premature slippage occurred at the slip-critically designed beam splice during the test. The experimentally observed frictional coefficients were as low as about 50% to 60% of nominal (code) value. Nevertheless, the bearing type behavior mobilized after the slippage transferred the increasing cyclic loads successfully, i.e., the consequence of slippage into bearing was not catastrophic to the connection behavior. The test result seems to indicate that the traditional beam splice design basing upon (bolt-hole deducted) effective flange area criterion may not be sufficient in developing the plastic strength of moment connections under severe earthquake loading. New procedure for achieving slip-critical beam splice design is proposed based on capacity design concept.

• 대한기계학회논문집
• /
• 제13권5호
• /
• pp.847-854
• /
• 1989

본 연구에서는 V-벨트 CVT의 핵심인 변속비-부하토오크-축력에 대한 이론적 연구에 이어 실험적 연구를 통하여 전 연구에서 구한 이론식과 비교 검토하고 V-벨트 CVT의 기초 설계자료를 얻고자한다.

• 한국공간구조학회논문집
• /
• 제19권1호
• /
• pp.65-73
• /
• 2019

This paper assesses the structural performance (force-slip response, slip modulus, and failure modes) of a CLT-concrete composite by conducting fifteen push-out test specimens. In addition, non-linear 3D finite element analysis was also developed to simulate the load-slip behavior of the CLT-concrete specimens under shear load. All 15 test specimens simulating the effect of concrete thickness, connection angle and penetration depth with four different shear connector types were built and tested to evaluate the flexural performance. Experimental results show that the maximum shear capacity for the composite action is obtained when the fixing angle is $90^{\circ}$ and the penetration depth of 95mm for SC normal screw was used to achieve ductile failure compared to other shear connectors.

• Steel and Composite Structures
• /
• 제13권3호
• /
• pp.239-258
• /
• 2012

In this paper, experimental investigations on high strength steel (HSS) stud connected steel-concrete composite (SCC) girders to understand the effect of shear connector density on their flexural behaviour is presented. SCC girder specimens were designed for three different shear capacities (100%, 85%, and 70%), by varying the number of stud connectors in the shear span. Three SCC girder specimens were tested under monotonic/quasi-static loading, while three similar girder specimens were subjected to non-reversal cyclic loading under simply supported end conditions. Details of casting the specimens, experimental set-up, and method of testing, instrumentation for the measurement of deflection, interface-slip and strain are discussed. It is found that SCC girder specimen designed for full shear capacity exhibits interface slip for loads beyond 25% of the ultimate load capacity. Specimens with lesser degree of shear connection show lower values of load at initiation of slip. Very good ductility is exhibited by all the HSS stud connected SCC girder specimens. It is observed that the ultimate moment of resistance as well as ductility gets reduced for HSS stud connected SCC girder with reduction in stud shear connector density. Efficiency factor indicating the effectiveness of high strength stud connectors in resisting interface forces is estimated to be 0.8 from the analysis. Failure mode is primarily flexure with fracturing of stud connectors and characterised by flexural cracking and crushing of concrete at top in the pure bending region. Local buckling in the top flange of steel beam was also observed at the loads near to failure, which is influenced by spacing of studs and top flange thickness of rolled steel section. One of the recommendations is that the ultimate load capacity can be limited to 1.5 times the plastic moment capacity of the section such that the post peak load reduction is kept within limits. Load-deflection behaviour for monotonic tests compared well with the envelope of load-deflection curves for cyclic tests. It is concluded from the experimental investigations that use of HSS studs will reduce their numbers for given loading, which is advantageous in case of long spans. Buckling of top flange of rolled section is observed at failure stage. Provision of lips in the top flange is suggested to avoid this buckling. This is possible in case of longer spans, where normally built-up sections are used.

• Steel and Composite Structures
• /
• 제29권1호
• /
• pp.107-123
• /
• 2018

The conception and experimental assessment of a removable friction-based shear connector (FBSC) for precast steel-concrete composite bridges is presented. The FBSC uses pre-tensioned high-strength steel bolts that pass through countersunk holes drilled on the top flange of the steel beam. Pre-tensioning of the bolts provides the FBSC with significant frictional resistance that essentially prevents relative slip displacement of the concrete slab with respect to the steel beam under service loading. The countersunk holes are grouted to prevent sudden slip of the FBSC when friction resistance is exceeded. Moreover, the FBSC promotes accelerated bridge construction by fully exploiting prefabrication, does not raise issues relevant to precast construction tolerances, and allows rapid bridge disassembly to drastically reduce the time needed to replace any deteriorating structural component (e.g., the bridge deck). A series of 11 push-out tests highlight why the novel structural details of the FBSC result in superior shear load-slip displacement behavior compared to welded shear studs. The paper also quantifies the effects of bolt diameter and bolt preload and presents a design equation to predict the shear resistance of the FBSC.

• KEPCO Journal on Electric Power and Energy
• /
• 제2권1호
• /
• pp.33-41
• /
• 2016

To verify that the friction damper used to high buildings as a kind of control technology of wind vibration can reduce dynamic behaviors of PTTs effectively, slip dampers in this paper are proposed to absorb the energy through relatively frictional movement of slip dampers applied to main post of a PTT (Power Transmission Tower) when dynamic displacement of a PTT occurs. The result of dynamic analysis is presented to determine the capacity of the damper system by controlling damping ratio on the resonance condition. It is observed that by installing slip dampers at a PTT the strain amplitudes of the main post caused by wind load are effectively reduced. Therefore it is shown that the proposed damper satisfies the strengthened wind-load design standards, and its efficacy was also validated experimentally by field testing.

• 한국산학기술학회논문지
• /
• 제10권8호
• /
• pp.2055-2061
• /
• 2009

고장력볼트 마찰이음에서 모재 및 덮개판을 과대공 제작하였을 경우 연결부의 내하력에 다소의 변화가 발생 될 수 있다. 본 논문에서는 고장력볼트 마찰이음에서 표준공과 과대공에 따라 미끄럼하중과 미끄럼계수의 변화를 파악하기 위하여 정적인장시험을 실시하였다. 정적인장시험결과 모재 및 덮개판의 과대공 제작에 따라 미끄럼계수의 변화가 다소 발생하였으나 이를 정형화시키기에는 다소 무리가 따랐으며, 미끄럼강도는 표준공 제작시의 값과 과대공제작시의 값이 최대 26%의 차이를 나타내었다. 그러나 이는 설계미끄럼강도를 초과하기 때문에 사용하중하에서 연결부의 사용성에 미치는 영향이 미약하므로 강부재 제작시 부득이하게 발생할 수 있는 과대공에 따른 규정을 보다 유연하게 적용시킨다면 구조물의 설계 및 시공시 효율성과 경제성 증대의 효과가 기대된다고 판단되었다.

• Steel and Composite Structures
• /
• 제34권1호
• /
• pp.91-105
• /
• 2020

Steel-concrete composite beam with profiled steel sheet has gained its popularity in the last two decades. Due to the ageing of these structures, retrofitting in terms of flexural strength is necessary to ensure that the aged structures can carry the increased traffic load throughout their design life. The steel ribs, which presented in the profiled steel deck, limit the use of shear connectors. This leads to a poor degree of composite action between the concrete slab and steel beam compared to the solid slab situation. As a result, the shear connectors that connects the slab and beam will be subjected to higher shear stress which may also require strengthening to increase the load carrying capacity of an existing composite structure. While most of the available studies focus on the strengthening of longitudinal shear and flexural strength separately, the present work investigates the effect of both flexural and longitudinal shear strengthening of steel-concrete composite beam with composite slab in terms of failure modes, ultimate load carrying capacity, ductility, end-slip, strain profile and interface differential strain. The flexural strengthening was conducted using carbon fibre reinforced polymer (CFRP) or steel plate on the soffit of the steel I-beam, while longitudinal shear capacity was enhanced using post-installed high strength bolts. Moreover, a combination of both the longitudinal shear and flexural strengthening techniques was also implemented (hybrid strengthening). It is concluded that hybrid strengthening improved the ultimate load carrying capacity and reduce slip and interface differential strain that lead to improved composite action. However, hybrid strengthening resulted in brittle failure mode that decreased ductility of the beam.

• 대한토목학회논문집
• /
• 제26권2A호
• /
• pp.327-338
• /
• 2006

강구조물의 대표적인 현장이음방식인 고장력볼트 마찰이음은 볼트 축력의 관리가 엄격하기 때문에 많은 노동력과 시간을 필요로 하며, 미끄러짐 하중을 기준으로 설계가 이루어져 볼트의 높은 전단강도를 유효하게 이용하지 못하고, 그 결과 소요 볼트수가 많아지는 단점이 있다. 따라서 고장력볼트 마찰이음의 단점을 보완하고, 지압이음의 장점을 살린 전단링을 사용한 새로운 이음방식을 개발하여 기존의 고장력볼트 마찰이음과 비교실험을 실시하고 해석적 연구를 실시하였다. 그 결과 전단링을 이용한 새로운 이음방식은 전단링의 높은 전단강도로 저항하기 때문에 기존의 마찰이음보다 이음부의 내력이 크게 향상되는 것을 실험적으로 확인할 수 있었다. 한편 전단이음의 응력집중을 최소화하면서 최대의 연결강도를 유도하기 위해서는 전단링의 깊이 등의 설계 변수에 대한 추가적인 연구가 필요할 것으로 판단된다.