• Journal of Chest Surgery
• /
• 제28권10호
• /
• pp.911-916
• /
• 1995

Thirteen patients with lung cancer have undergone bronchoplastic procedures from January 1991 to July 1994 in Kyung Hee univ. Hospital.Among them,twelve patients were male and one patient was female from 33 to 76 years of age.[ mean 56.6 11.5 years of age The pathologic diagnoses were squamous cell carcinoma in twelve patients and adenoid cystic carcinoma in one patient.The bronchoplastic procedures consisted of seven right upper sleeve lobectomies, one right middle sleeve lobectomy, one left lower sleeve lobectomy and four sleeve pneumonectomies. In these sleeve pneumonectomies, right sleeve pneumonectomy was done in three patients and the other was left sleeve pneumonectomy. Including the four sleeve pneumonectomies, carinoplasty was performed in seven patients. Postoperatively, we carried out bronchoscopic suction of intrabronchial secretions in necessary for the prevention of postoperative complication. All except one were discharged without any complication and have been in good condition. Postoperative mortality was in one patient who expired 25days after right middle sleeve lobectomy with respiratory failure.

• 한국의상디자인학회지
• /
• 제13권1호
• /
• pp.59-71
• /
• 2011

As an exaggerated-shoulder becomes a growing trend women's clothing, the crescent shaped sleeve with parallel style lines in the arm hole is a highly used women's sleeve pattern. This study develops and provides an applicable method for making the crescent shaped power shoulder sleeve. An efficient basic method for making the 2 piece crescent shaped sleeve was developed and the sensory appearance test was carried out with experimental clothes. There are two principles for making the crescent shaped sleeve: having a style line in the sleeve and pasting part of the cut arm hole of the bodice to the sleeve. The latter would be more convenient for a 2 piece sleeve, mostly used for jackets. The crescent shaped sleeve used in power shoulder jackets should set the shoulder angle as you wish to extend and raise the shoulder point of the bodice and sleeve to the same height. For a stronger power shoulder image, a 3 piece sleeve has a better appearance. Also, the height of the shoulder has to be enhanced with a shoulder pad for a more stable sleeve.

• Structural Engineering and Mechanics
• /
• 제13권1호
• /
• pp.1-16
• /
• 2002

This paper presents the findings of an investigation carried out to determine the most appropriate connections, in terms of rotational stiffness, to use for the optimum design of cold-formed Zed section sleeve joint purlin system. Experiments and parametric studies were conducted to investigate the effects of geometric variables on the behavior of the sleeve-purlin and cleat-purlin connections of the sleeve joint purlin system. The variables considered were purlin size and thickness, sleeve size, thickness, length and bolt position. The test results were used to verify the empirical expressions, developed herein, employed to determine the rotational stiffness of connections. With the predicted connection stiffness, the most suitable sleeve-purlin and cleat-purlin connections can be selected so as to produce an optimum condition for the sleeve joint purlin system.

• 한국의상디자인학회지
• /
• 제10권2호
• /
• pp.105-115
• /
• 2008

Men's outer wear, such as jackets and coats appeared since the 16th century. They have been changed from doublets, coats, justaucorps, tail-coats, frock coats and morning coats to contemporary men's suits. Since the early 17th century, sleeve patterns of men's outer jackets had been mostly two-pieces close fitted patterns. The purpose of this article is to compare sleeve patterns of various jackets, which appear in various historic costume books. Armhole measurements, sleeve head measurements, amounts of ease, armhole depths, armhole widths, crown heights, sleeve width and sleeve angle had been compared to find out the differences among patterns of different times and styles. Coming to the present, the difference between top sleeve and under sleeve became more obvious, and the sleeve angle became less curvy. Another interesting point is that there had been considerable amounts of ease, which is the difference between sleeve head measurements and corresponding armhole measurements. It is because the sleeve has been attached to the armhole not by seam but by string. It is believed that the present sleeves have more natural curve and shape compared to the past.

• Structural Engineering and Mechanics
• /
• 제41권3호
• /
• pp.379-393
• /
• 2012

Of the various methods of splicing reinforcing bar in reinforced concrete structure, mortar-filled sleeve reinforcement splice offers diverse benefits, not only in terms of structural performance but also for the construction process. Consequently, after the mortar-filled sleeve splices have been developed in recent years, research and development on these splices has been actively carried out, in order to evaluate its macro structural performance, such as its strength and stiffness, with the aim of enabling this system to be applied to construction in the field as early as possible. However, to make a proper evaluation on the overall structural performance of the mortar-filled sleeve reinforcing bar splice, it is of critical importance to understand the lateral confining action of the sleeve, which is known to affect the bond strength between the embedded bar and mortar in the sleeve. Accordingly, in this study, an experiment of monotonic loading and cyclic loading was conducted with a full-sized mortar-filled sleeve splice attaching strain gauges on the sleeve surface with experimental variables such as development length of bar, etc. Based on the test results, the effect of the lateral confining action of the sleeve was analyzed and considered in terms of the bond strength between the bar and mortar in this splice.

• 한국지역사회생활과학회지
• /
• 제24권4호
• /
• pp.457-469
• /
• 2013

The purpose of this study is to quantitatively analyze the impacts of the distribution of easing contraction of the sleeve on the external appearance of bodice and sleeve through virtual clothing simulation. Virtual clothing is conducted by differentiating the sleeve easing in accordance with the experimental condition of bodice and sleeve that are followed by draping. And then the evaluation is carried out. As a result of an analysis of the similarity between the virtual garment and the actual clothing, the whole external appearance of the bodice and sleeve was expressed similarly. The external appearance according to the distribution of easing contraction got better as the easing contraction of sleeve was concentrated on sleeve cap in front while the appearance was better at the back as it was more gently distributed than in the front. In a comparison of armhole form, the clothing of which the top of it was most similar to S0 was S4 in which the gap between the armhole and the arm was the least and the front and rear silhouette fell relatively well. In a comparison between the position of bust circumference line and that of the sleeve base line, the front of the sleeve matched the bust circumference line as the easing contraction was distributed close to the center of the sleeve cap while in the back, the sleeve base line and the bust circumference line matched when some easing contraction ratio was added close to the armpit point. The cross section figures of garment space of the shoulder, the margin was evenly distributed in S4 or S5 with differing distributions of easing contraction in the front and the back. This study is significant in that it supplies the objective baseline data which makes a novice more able to make a good external appearance of the sleeve.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.461-461
• /
• 2008

According to previous report, aged sleeves for old transmission lines have various defect such as biased installation or corrosion of steel sleeve. These defects occupied almost 50 percent of investigated aged sleeves. The defects have been limited power capacity of transmission line. And it can cause serious problems such as rapid increasing of sag or falling out of overhead conductor from sleeve. This paper study on thermal behavior of sleeve with various defect model. The detailed results were presented in the text.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.502-505
• /
• 2008

Due to continuous difficulty of human power supply, it is necessary to develop an equipment which is good to saving cost and time at a construction site. A quick pipe coupling method is the kind of mechanical joint system using split-sleeve and sealing-pad at pipe groove without welding. In hence, it provides restrained pipe joint which is simple, safe, and dependable without environmental pollutions. It is more useful scheme than the other ones. The purpose of this study is to find out the main design factors and the optimum shape of split-sleeve. The stress analyses were carried out under various shapes of pipe groove configuration, materials and internal pressures with a commercial software, ANSYS workbench which uses FEM(finite element method). Results are graphically depicted with various parameters.

• 한국자동차공학회논문집
• /
• 제9권2호
• /
• pp.210-215
• /
• 2001

The pole antenna of vehicles for AM/FM radio broadcasting receptions has many probems, such as damageable mechanical system and noise etc. It is considered that noise is composed of the structural vibration noise and the air flow induced aerodynamic noise. Also we find out that the setting process of a printed on-glass automobile antenna has many difficulties. Recently, the above mentioned problems can be reduced by employing enhanced wiper antenna which utilizes the windshied wiper arm. The new system is a passive antenna. In this study, experiments for the characteristics of a wiper antenna by measuring the SWR, radiation pattern and received powe have been carried out. The experimental results show that the efficiency of the wiper antenna has better performance than any other antenna.

• 대한가정학회지
• /
• 제48권2호
• /
• pp.85-94
• /
• 2010

Comparative analysis of marker efficiency in blouse patterns, based on different sleeve designs, was carried out. Sleeve designs used included set-in-sleeve, laglan sleeve, and epaulet sleeve. The two types of epaulet sleeves, A and B, are based on pattern arrangement methods of center back. Cloth and production conditions are the width of cloth, the number of marking pieces, and the direction for marking deployment. A blouse pattern saved to the PAD CAD System was graded with different sizes and arranged for industrial purpose to calculate the marker efficiency in different conditions. The results were as follows. On the whole, the marker efficiency of small pattern sized set-insleeve was higher than laglan and epaulet sleeve designs. It was also established that marker efficiency is dependent on cloth and production conditions. For small number of marking pieces, efficiency was higher in the condition of 110cm cloth widths compared with that condition of 150cm cloth widths. However the efficiency of large number of marking pieces was higher in the condition of 150cm cloth widths.