• The Journal of the Korean dental association
• /
• v.13 no.2
• /
• pp.133-136
• /
• 1975

The autor studied skin reactions and their incidences among 130 dental students and dentists to 2% Iidocaine HCI, 2% procaine HCI, direct resin, plaster of paris, zinc oxide-eugenol cement, and adhesive plaster by Patch test. The results of the studies are as follows: 1. Eighteen cases out of 130 revealed slight positive reaction toa 1 or 2 allergens. 2. Lidocaine HCL showed 1 case, procaine HCL 4 cases, direct resin 4 cases, Z.O.E. cement 1 case, adhesive plaster 13 case, and plaster of paris showed none. 3. Two delayed reaction were detected after 48 hours, one of which reacted both lidocaine HCL and direct resin, and the other one was a case of adhesive plaster.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.2
• /
• pp.296-304
• /
• 2014

For this research, prepared polyurethane dispersion of hard segment type and polyethylene emulsion wax. Use these resin, this article has been analyzed about mechanical properties variation by increasing amount of polyethylene emulsion wax on Lam skin leather and dried film. According to measure data for solvent resistance, PUD had good property. As known in the results, increase of polyethylene wax constant did not influence to big variation of hybrid resin properties. As test of tensile strength, PUD had good tensile characteristic($1.235kg_f/mm^2$) and PUD-EW4 had lowest tensile characteristic($1.022kg_f/mm^2$). As same as tensile characteristic, abrasion test determined PUD(52.225 mg.loss) had highest properties. In elongation case, PUD showed 698 % modulus which was best properties in this experiment.

• Composites Research
• /
• v.28 no.6
• /
• pp.372-377
• /
• 2015

In this study, we analyzed process numerically when a bogie frame skin is manufactured by applying resin transfer molding process using composite material instead of steel. Processing time was compared based on the various thickness of bogie frame skin and the weight variation of a skin was also considered. As a result, RTM processing time decreases and the weight of a bogie reduces as the thickness of frame skin increases with the assumption that fiber volume is constant inside the skin. By considering these results as the information to estimate the production cost, trade-off between two fields, processing time and structural properties, can be performed in design optimization to produce bogie frame.

• Tribology and Lubricants
• /
• v.32 no.6
• /
• pp.201-206
• /
• 2016

In this study, we attempt to produce a semi-elliptical riblet with a shark skin-like surface using wire electrical discharge machining (WEDM) and micro molding techniques. Our design for the production of the semi-elliptical mold includes an electrode, a winding roller, and a guide on the WEDM system. A replication mold with negative riblets is machined using WEDM, and a shark skin inspired surface with positive riblets is fabricated using a micro molding technique. For a comparison with the original shark skin, a shark skin replica is also produced using the micro molding technique directly from a shark skin template. Droplet contact angles on a flat surface, the shark skin replica, and the epoxy resin-based micro riblet shark skin-like surface are evaluated. The effect of a Teflon coating on the contact angles for the three different surfaces is also investigated. The results show the micro riblet with a shark skin-like surface has a similar contact angle as the shark skin replica, which means that the simplified riblet shark skin surface strongly influences the performance of wettability. This study confirms the effectiveness of using the WEDM method to prepare hydrophobic surfaces with diverse surface patterns.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.1
• /
• pp.83-90
• /
• 2017

The polyurethane resin used for the garment skin leather surface coating was synthesized by varying the content of polyethylene glycol (PEG) in [NCO] / [OH] mole % ratio. The mechanical properties of the synthesized polyurethane resin were analyzed by SEM, FT-IR, UTM. As the [NCO] / [OH] mole % ratio of nonionic poly ethylene glycol (PEG) increased, there was no change in flexural resistance (dry, wet) and abrasion resistance and tensile strength measurement value were lowered. In contrast, the elongation property values were increased. The result of viscosity measurement showed that the viscosity became thinner with increasing [NCO] / [OH] mole % of PEG.

• Proceedings of the SCSK Conference
• /
• 2003.09a
• /
• pp.417-430
• /
• 2003

A new method was developed to prepare microcapsules involving hydrophobic components. A totally new "silicone-resin-polypeptide" was used as the wall materials. The polypeptide was made by hydrolysis of collagen and silk protein and so on, and that was combined with silicone. This microcapsule was easily prepared from silicone-resin-polypeptide in water solution. The ratio of encapsulation in the microcapsule was not only high level as 90％, which had never been reached, but also the particle size could be controlled to obtain very small size (average particle size: 2${\mu}{\textrm}{m}$). Moreover, these microcapsules were resistant to high shearing forces and were stable over a long time period. This stable microcapsule was not crushed in pressure with finger spreading, so the core materials hardly touch the skin directly. Application in cosmetics by using microcapsule involving UV absorbents (2-ethylhexy1-4-methoxycinnamate (OMC) and 4-tert-butyl-4' -methoxydibenzoyl-methane (BMDBM)) was examined. It was possible to apply organic UV absorbents in water-rich formulations without any surfactant by using this microcapsule. This formulation demonstrated a good moisturizing and soft skin feel. Therefore, the microcapsule was applied to hair care products. As a result, the sunscreen hair lotion with microcapsule was able to prevent from damaging and decoloring of hair color by UV rays. As just, it was suggested that this microcapsules were be widely applied in cosmetics.cosmetics.

• Archives of Pharmacal Research
• /
• v.18 no.4
• /
• pp.224-230
• /
• 1995

Recently, many attempts have been made to use hydrogels of various polymers as delivery systems of various drugs and bioactive materials to prolong and control their phamacological activities. In this study, we have evaluated the physico-chemical properties of methacrylic acid-methyacrylic acid methyl ester copolymer 9Eudispert mv)m a acrylic resin hydorgel, and its application to transdermal delivery system. In the dissolution tests, the release rate of salicylic acid (SA) and sodium salicylate (SOd. SA) were faster than lidocain (LD) and lidocain-HCl(LD-HCl). As the concentration of Eudispert mv polymer increased, the extensibility of Eudispert mu hydrogel decreased, whereas the swelling ratio increased. The more NaOH and polymer concentration increased, the more osmotic pressure linearly increased. The skin permeation of Sod. SA, an acidic model drug, was remarkably enhanced by Eudispert mv hydrogel. All fatty acids, except for Sod. glycolate, dramatically increased the skin permeation flux in Eudispert mu hydrogel containing LD-Hcl, a basic model drug. Consequently, it is suggested that Eudispert mv hydrogel may be used as potential transdermal delivery vehicle.

• Journal of Adhesion and Interface
• /
• v.19 no.1
• /
• pp.5-12
• /
• 2018

The purpose of this study is to evaluate the adhesive properties of polyurethane mixed aqueous dispersions by omitting the primer, dealing with the preparation of skins for synthetic leather with excellent adhesion by omitting the pre-treatment process. The two-component mixed polyurethane water dispersion was prepared by synthesizing an ester-based polyurethane resin (PU-T) and a carbonate-based polyurethane resin (PU-C) to obtain the final resin. As a result of measuring the peel strength of the adhesive specimens omitting the pre-treatment agent, it was confirmed that the state adhesive strength (ethylene vinyl acetate (middle): $4.2kg_f/cm$ and rubber (outsole): $4.4kg_f/cm$) there was. This makes it possible to omit the pre-treatment process which has been indispensably used in the shoe manufacturing process, thereby reducing the process time and reducing the amount of volatile organic compounds (VOCs) generated in the pre-treatment product, resulting in environmentally advantageous.

• Fashion & Textile Research Journal
• /
• v.7 no.1
• /
• pp.81-84
• /
• 2005

Skin patch test and antibacterial properties of the reaction products between poly(hexamethyl biguanide) hydrochloride and trimethylol melamine on textile fabrics were examined. Antibacterial activities of anti-microbial agent treated samples are very good. The reduction ratios against four kinds of colonies are 99.9 % after repeated laundering ten times. Skin patch test results for anti-microbial agent treated samples are almost-negative by Hi-scope judgement and macroscopical judgement.

• Restorative Dentistry and Endodontics
• /
• v.34 no.1
• /
• pp.38-41
• /
• 2009

When we use the total-etch dentin adhesive system for composite resin restorations, gel or liquid acid etchant such as 37% phosphoric acid is commonly used. Thirty seven percentage phosphoric acid is very powerful erosive agent, and can cause severe harmful effects when it contacts with an oral mucosa and facial skin. This case describes iatrogenic chemical burn on facial skin caused by phosphoric acid which was happened during composite resin restorative procedure. Chemical burn by acid etchant can be evoked by careless handling of remnant and syringe. In order to prevent these iatrogenic injuries, we should check the complete removal of the etching agent both in intra and extra-oral environments after etching and rinsing procedure and it is necessary to use of the rubber dam or isolation instruments. If accidental burn were occurred. immediate wash with copious water. And bring the patient to the dermatologist as soon as possible.