• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.6
• /
• pp.573-578
• /
• 2013

In the case of the Back EMF voltage contains the harmonics, the motor torque ripple and vibration is occurred by the current pulsation, because IPMSM control algorithm is the model which is assumed that it contains a sinusoidal Back EMF voltage. To improve ride quality, in the case of IPMSM for EV, improving the torque control characteristics is necessary. Therefore, there is a need to minimize the influence of the harmonics. In this paper, the investigation to decrease the current distortion factor has been performed for improving torque control characteristics by applying the non-sinusoidal Back EMF to IPMSM model.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.1
• /
• pp.59-65
• /
• 2014

To obtain an elliptical trajectory at the cutting edge during elliptical vibration cutting, sinusoidal voltage excitations of two piezoelectric actuators have commonly been used. In this study, PWM excitation, which is relatively simple to generate, was employed and its characteristics were investigated. In experimental and analytical analyses, we found that for PWM excitation, the integer-multiple frequencies of the excitation voltage distorted the shape of the elliptical trajectory, whereas at a duty ratio(DR) of 50%, the distortion of the elliptical trajectory was minimized due to disappearance of the first overtone. When the magnitude of the maximum excitation voltage was maintained at the same level for both PWM and sinusoidal excitation, PWM (DR=50%) excitation produced a greater vibration amplitude than sinusoidal excitation but resulted in more rapid saturation of a high-frequency power amplifier.

• 전기의세계
• /
• v.21 no.2
• /
• pp.25-33
• /
• 1972

The main focus of this paper is on the study of voltage-current characteristics in disk-type siliconcarbide resistors. For each of the 15 different sintering and other process conditions, 10 samples were prepared. Experiments performed with each sample consist of supplying sinusoidal AC current of a few miliamperes after conditioning-shots with 400ma. Experimental data were examined with regard to the relationship between the process conditions and the nonlinear resistivity. The examination suggests several possibilities of improving the nonlinlinear characteristics of siliconcarbide resistors while maintaining low resitance. One of those possible conditions is to sinter the powdered SiC and the binding materials approximately 2 hours in nitrogen. In addition to describing the nonlinear characteristics of siliconcarbide resistors, this paper also presents the distortion characteristics of current waves vs. the nonlinear exponent, n. Photographical results show that the more nonlinear characteristics samples have, the more distorted current waves are.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.62 no.1
• /
• pp.45-49
• /
• 2013

High frequency system has been used for the purpose of skin care and obesity treatment, by high-frequency energy is applied to the human body generates deep heat. Conventional high frequency system could not selection control by depending on the body load fluctuations. Such as burns and side effects have been reported by system instability and then therapeutic effect is insufficient. During treatment, objective information about the status of the patient was no. Because of treatment methods are subjective, and so tailored treatments were impossible. In this paper, high frequency medical system with sinusoidal frequency characteristics without distortion of the Push pull switching scheme for pain relief therapy was designed. And control circuit that was designed by feedback using the output changes according to the body-load fluctuation. Last, power circuit for efficient control the heat generated from the hardware was proposed.

• Journal of IKEEE
• /
• v.11 no.3
• /
• pp.122-128
• /
• 2007

Sinusoidal voltage-controlled oscillators (VCOs) based on Colpitts and Hartley oscillators are presented. They consist of a LC parallel-tuned circuit connected in a negative-feedback loop with an OTA-R amplifier and two diode limiters, where the inductor is simulated one realized with temperature-stable linear operational transconductance amplifiers (OTAs) and a grounded capacitor. Prototype VCOs are built with discrete components. The Colpitts VCO exhibits less than 1% nonlinearity in its current-to-frequency transfer characteristic from 4.2 to 21.7 MHz and ${\pm}$95 ppm/$^{\circ}C$ temperature drift of frequency over 0 to $70^{\circ}C$. The total harmonic distortion (THD) is as low as 2.92% with a peak-to-peak amplitude of 0.7 V for a frequency-tuning range of 10.8-32 MHz. The Hartley VCO has the temperature drift and THD of two times higher than those of the Colpitts VCO.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.876-881
• /
• 1998

The compensation strategy of shunt active power filters is one of the most important link that determine its compensation characteristics. In this paper, a new interpretation of the instantaneous reactive power theory in three-phase circuits was proposed. A compensation strategy (ip, iq mode) was introduced on the basis of the new interpretation. This compensation strategy was compared with other two compensation strategies(P, q mode and UPF mode). When source voltage is distorted, a sinusoidal, the three compensation strategies are equivalent to each other. When source voltage is distorted, a sinusoidal source current may result only by using ip, iq mode. This is the advantage of ip, iq mode. The result is verified by simulation.

• Proceedings of the KOSOMBE Conference
• /
• v.1991 no.11
• /
• pp.103-106
• /
• 1991

A three-dimensional finite element model of a ligamentous two motion segments (L4-S1) was developed to investigate its dynamic response. A number of parameters like the intradiscal pressure, forces in ligaments. and across facet joints in response to a sinusoidal axial compression force (-360 N to -440 N at 5 Hz) were predicted. The increase in the parameters varied from 12% to as high as 50% in comparison to response for a static load of 400 N. The predicted parameters also revealed a distortion and a phase shift in comparison to the applied sinusoidal signal. These changes may lead to degenerative changes seen clinically in persons exposed to a chronic vibration environment over time.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.7
• /
• pp.80-85
• /
• 1996

A sinusoidal tuned VCO based on linear OTA's has been designed for instrumentation and measurement applications. It consists of a noniverting amplifier, a hard limiter, and a current controlable LC-tuned circuit which is realized vy two linear OTA's and two grounded capacitors. A prototype circuit has been built with discrete components. The experimental results show that the proposed VCO has a linearity error of less than 6.5 percent and a temperature coefficient of less than 200ppm/$^{\circ}C$ over a bias current range form 5$\mu$A to 100 $\mu$A(or an oscillation frequency range form 775.5 Hz to 20.371 kHz). A total harmonic distortion of 0.6 percent was measured for a peak-to-peak amplitude of 5V.

• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.58-60
• /
• 1998

The precise measurement of consumed power during the given time is very important in the energy management aspect. Up to days, induction watthour meter has been designed for use in the alternating circuits in which the voltage and current are essentially sinusoidal. The use of switching elements in power system causes the current or voltage involving harmonics. Therefore the registration error is caused by harmonics in the equipment for measuring power. This paper presents the registration error of the induction watthour meter in the presence of harmonic distortion. The accuracy of a watthour meter on loads in which the input source is not sinusoidal is investigated. And the effects of individual harmonic are reported by experiment.

• Proceedings of the KIPE Conference
• /
• 2002.11a
• /
• pp.137-139
• /
• 2002

This paper proposes a four times DC-link voltage PWM power converter, which is constructed by four cascade connected power switching devices. such as IGBT. These four switching devices are controlled by a sinusoidal PWM method to obtain a DC-link voltage. which is higher than 4 times the peak supply voltage, and to suppress input current harmonic components. achieving a sinusoidal current waveform with less than $3[\%]$ distortion. Which is also constructed by four cascade connected IGBT. by the simulation result.