• Progress in Superconductivity and Cryogenics
• /
• v.4 no.2
• /
• pp.16-20
• /
• 2002

Bi-axially textured Ni tapes for YBCO coated conductors were Prepared by cold rolling and heat treatment of Ni Powder compacts. The Ni powder used in this study was 5 urn in particle size and 99.99 % in purity. The process of this study consists of filling of hi powder into a rubber mold, cold-isostatically Pressing and sintering of the powder compacts at 110$0^{\circ}C$ for 6h in 96 % Ar - 4 % H$_2$ atmosphere. The sintered compacts were cold rolled with a 5 % step reduction ratio into a 100 micron-thick tapes and then heat-treated at 100$0^{\circ}C$ for various time periods. The (200) texture of Ni tape was successfully developed through the recrystallization heat treatment of the cold rolled Ni tapes. At 100$0^{\circ}C$, the degree of texture of the heat-treated Ni tapes seems not to be significantly affected by the heat-treatment time. The short heat treatment of S min was sufficient to develop the complete (200) cube texture. The degree of in-Plane and out-of-plane texture of the prepared Ni tapes was 8-10$^{\circ}$. The heat treated Ni tapes consisted of equiaxed grains with a size 50-70 microns. and the AFM sol-face roughness was as smooth as 3 nm.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.14 no.3
• /
• pp.25-31
• /
• 1977

Fe V spinels were prepared by sintering the well-ground stoichiometric mixtures of Fe O and V O at 1,10$0^{\circ}C$ under H -CO atmosphere. The activation energy for electrical conduction decreases with increasing amount of iron. The tendency of activation energy depending on the amount of iron contained clarifies that the electrical condction of the spinel is mainly due to electron hopping between Fe and Fe ions at B sites. In the experiment for negative resistance characteristics, the threshold voltage (Vth) for the samples is related to ambient temperature, thickness and raising rate of applied voltage. Vth decreases as temperature increases while Vth increases linearly with thickness and Vth increases linearly with the raising rate of applied voltage in semi-logarithmic scale. These results lead to a conclusion that current paths mainly formed by thermal breakdown are ascribed to the negative resistance phenomena. Applying this property, these vanadium iron spinels may be used for switching elements.

• Journal of the Korean Ceramic Society
• /
• v.40 no.3
• /
• pp.301-308
• /
• 2003

Glass-infiltrated alumina, which can be used as an all-ceramic dental crown, was prepared. The glasses in the system of SiO$_2$-B$_2$O$_3$-Al$_2$O$_3$-CaO-La$_2$O$_3$with various amount of $Al_2$O$_3$infiltrated into a porous sintered alumina. The effect of $Al_2$O$_3$on the infiltration characteristics and its mechanical strength were studied. The corrosion of the sintered alumina by infiltrated glasses was prevented by increasing the amount of $Al_2$O$_3$in the glass batches, this increased the bending strength of the glass infiltrated alumina composite. The crack like voids in the sintered alumina was a cause of the deteriorating the mechanical strength of the composite, and this can be eliminated by sintering the alumina at 130$0^{\circ}C$. Glass infiltration under the vacuum atmosphere enhanced the hording strength of the composite up to 453$\pm$31 MPa.

• Transactions on Electrical and Electronic Materials
• /
• v.3 no.3
• /
• pp.21-24
• /
• 2002

Two kinds of $Nd_{1+X}Ba_{2-X}Cu_3O_{7-{\delta}}$, the sintering samples and zone melting samples, were heat-treated under pure Ar at 950$^{circ}C$. The substitution of Nd ion for Ba ion in the $Nd_{1+X}Ba_{2-X}Cu_3O_{7-{\delta}}$ before and after the heat treatment was investigated by XRD. In order to confirm the effects of the heat treatment, the Tc and Jc of samples with/without the heat treatment under Ar were comparatively studied. $Nd_{1+X}Ba_{2-X}Cu_3O_{7-{\delta}}$ samples were oxygenated under pure oxygen at $300^{circ}C$. From the XRD pattern it was found that the sample with x<0.4 was transferred from tetragonal phase to orthorhombic phase after the oxygenation, while the sample with x>0.4 did not show the phase transition even after a long time oxygenation. Therefore, the low oxygen partial pressure (Ar+1 % O$_2$) was used for the ambient atmosphere of the zone-melting samples, which could reduce the melting temperature and depress the substitution of Nd for Ba. After the improvement in the zone-melting process, the Jc value was increased to 2 x $10^4$A/$cm^2$ (0 T, 78 K). The particle orientation and the structure of zone-melted NdBaCuO were studied by the XRD and SEM analysis.

• The Journal of Engineering Research
• /
• v.5 no.1
• /
• pp.63-72
• /
• 2004

The properties of electrical resistance of Mn-Co-Ni-Fe oxide-based thermistor with various Fe contents in sintering process at $1200^{\circ}$ to $1400^{\circ}C$ for 4 hours in air atmosphere for fabricating thermistor materials were investigated. The results were as follows: all samples showed single cubic spinel crystal structures in all region. The electrical conductivity is the highest thermistor sintered at $1300^{\circ}C$ for 4 hours. In general when the Fe content is increased except F-2, the resistivity increases and relatively the conductivity decreases. Particularly F-2 composition exhibited the highest electrical conductivity (1.4${\times}$$10^-3$${\textohm}cm) and relatively low B constant(2906K)

• Korean Journal of Materials Research
• /
• v.2 no.5
• /
• pp.360-365
• /
• 1992

Ga-doped polycrystalline ZnO films on glass substrates were prepared by sputtering the targets, which had been prepared by sintering discs consisting of ZnO powder and various amounts of G$a_2O_3$, to investigate the effects of gallium doping and sputtering conditions on electrical properties. Optimizing the RF power density, argon gas pressure and gallium content, transparent Ga-doped ZnO films with resistivity less than 1$0^{-3}$ohm-cm are obtained. Electron concentration of undoped and Ga-doped ZnO films are order of $10^{18}$, $10^{21}$/c$m^2$respectively. After heat treatment in air and $N_2atmosphere, $ the resistivity of Ga-doped ZnO films increases by about two orders of magnitude. The optical transmission is above 80% in the visible range and the optical band widens as the Ga content increases.

• Korean Journal of Materials Research
• /
• v.17 no.10
• /
• pp.560-566
• /
• 2007

AlN plates were fabricated by hot pressing at $1700-1900^{\circ}C$ using yttria and alumina (3 and $10\;{\mu}m$ particle size) powders as additives and characterized: density, thermal conductivity, transverse rupture strength, and grain size measurement by SEM and EDS. Density values of $3.31-3.34\;g/cm^3$ are largely attributed to hot pressing of powder mixtures in carbon mold under $N_2$ atmosphere which caused effective degree of oxygen removal from yttrium-aluminate phase expected to form at $1100^{\circ}C$. The grain size of hot pressed AlN was almost homogeneous, with size approximately from 3.2 to $4.0\;{\mu}m$ after hot pressing. $Al_2O_3$ powder of $3\;{\mu}m$ particle size resulted in better transverse rupture strength and finer grain size compared to $10\;{\mu}m$ $Al_2O_3$ powder. The thermal conductivity of AlN ranged between $83-92.7\;W/m{\cdot}K$ and decreased with $Al_2O_3$ addition. Fine grain size is preferred for better mechanical properties and thermal conductivity.

• Journal of Electrochemical Science and Technology
• /
• v.15 no.1
• /
• pp.168-177
• /
• 2024

Ni-rich cathode is one of the promising candidates for high-energy lithium-ion battery applications. Due to its specific capacity, easy industrialization, and good circulation ability, Ni-rich cathode materials have been widely used for lithium-ion batteries. However, due to the limitation of the co-precipitation method, including sewage pollution, and the instability of the long production cycles, developing a new efficient and environmentally friendly synthetic approach is critical. In this study, the Ni_0.91Co_0.06Mn_0.03CO₃ precursor powder was successfully synthesized by an efficient spray-drying method using carbonate compounds as a raw material. This Ni_0.91Co_0.06Mn_0.03CO₃ precursor was calcined by mixing with LiOH·H₂O (5 wt% excess) at 480℃ for 5 hours and then sintered at two different temperatures (780℃/800℃) for 15 hours under an oxygen atmosphere to complete the cathode active material preparation, which is a key component of lithium-ion batteries. As a result, LiNi_0.91Co_0.06Mn_0.03O₂ cathode active material powders were obtained successfully via a simple sintering process on the Ni_0.91Co_0.06Mn_0.03CO₃ precursor powder. Furthermore, the obtained LiNi_0.91Co_0.06Mn_0.03O₂ cathode active material powders were characterized. Overall, the material sintered at 780℃ shows superior electrochemical performance by delivering a discharge capacity of 190.76 mAh/g at 1^st cycle (0.1 C) and excellent capacity retention of 66.80% even after 50 cycles.

• Economic and Environmental Geology
• /
• v.37 no.3
• /
• pp.303-309
• /
• 2004

Pyrochlores were known as promising materials for the immobilization of radioactive actinide. Accordingly, we synthesized pyrochlores with Gd$_2$Ti$_2$$O_7$ and Gd$_2$Zr$_2$$O_7$compositions by sintering method, and studied its properties and phase relations in Gd-Ti-O and Gd-Zr-O system. The mixed powders were pressed into pellets under 200-400 kgf/cm$^2$ at room temperature. and then sintered at 1000-1$600^{\circ}C$ for 0.5-40 hours. The synthesized samples were analyzed and were identified with XRD and SEM/EDS analyses. The optimal synthetic conditions of pyrochlores with Gd$_2$Ti$_2$$O_7$composition were at 140$0^{\circ}C$/0.5hrs, 130$0^{\circ}C$/3hrs and 120$0^{\circ}C$/20hrs. Its chemical composition was $Gd_{2.0-2.1}$$Ti_{1.9-2.0}$$O_7$ and similar to the stoichiometric composition without any relationship in temperature and atmosphere. The optimal synthetic conditions of pyrochlores with $Gd_{2}$$Zr_{2}$$O_7$composition were at 155$0^{\circ}C$/40hrs and 1$600^{\circ}C$/30hrs. The compositions of pyrochlore synthesized from these optimal conditions were irregular with $Gd_{1.5-2.4}$$Zr_{1.7-2.4}$$O_7$. Such heterogeneity indicates that the reaction rate of pyrochlore with Gd$_2$Zr$_2$$O_7$composition is very low, and then its equilibrium state could not be attained even for 40 hours which was the longest sintering time in this research.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.6
• /
• pp.317-328
• /
• 2019

In this work, we investigated clay and raw materials from China (black clay, red clay, white clay) and Korea (Cheonan clay, Obu clay) used for the manufacture of porcelain products. According to chemical analysis results, feldspar components containing CaO, K₂O, Na₂O and quartz are found in clay materials besides primary clay such as kaollinte, for the clay materials from Korea, which is found more in clay materials from Korea than from China. For the Fe₂O₃ content, governing whiteness of porcelain products, more iron oxide (> 5 %) is found in Korean clays (Cheonan clay, obu clay, red clay) compared to those form China (black, white clay). Through X-ray diffraction analysis, kaolinite and Halloysite are found to be main phases for all the raw materials and second phases such as quartz and pyrophyllite are found. Using these clay materials, raw materials for porcelain products were produced, and the physicochemical properties were investigated for sintered samples. Absorption rate is in order of Baekja-A < Baekja-B < Yeonbuncheong < Jinbuncheong < Cheongja, and the sample, sintered at 1250℃ in reductive atmosphere, exhibits the lowest absorption rate. Comparing the color of the sintered samples, the samples sintered in oxidative atmosphere (L^* value: 86~95 %) show higher whiteness value than those sintered in reductive atmosphere (L^* value: 81~93 %). For the Cheongja and Buncheong, the samples sintered in reductive atmosphre shows higher whiteness, L^* values, and low a^*/b^* value, which is due to reduction of iron oxide (Fe₂O₃).