• Korean Journal of Materials Research
• /
• v.14 no.7
• /
• pp.522-528
• /
• 2004

Heat analysis of the plate type and wave type heat sink were carried out by using computational simulation. The heat resistance and air flow of two heat sink models were analysed according to natural and forced convection condition and positions of fan. When a fan was at the position of z-axis and y-axis in forced convection, the heat resistances of plate type heat sink were $0.17^{\circ}C/W$, and $0.28^{\circ}C/W$ respectively. In the case of wave type heat sink, they were $0.18^{\circ}C/W$ and $0.53^{\circ}C/W$. As the air flow velocities were averagely $0.386\;m/s\~3.269\;m/s$, air flow velocity of plate type heat sink was faster than that of wave type. In this experiment, it was observed that the plate type heat sink showed a good ability of heat radiation comparing with wave type one.

• Journal of Korea Multimedia Society
• /
• v.20 no.4
• /
• pp.640-648
• /
• 2017

Sensors have limited resources in sensor networks, so efficient use of energy is important. In order to use the energy of the sensor node efficiently, researches applying mobile sink to the sensor network have been actively carried out. The sink node moves the sensor network, collects data from each sensor node, which spread the energy concentrated around the sink node, thereby extending the entire life cycle of the network. But, when the sink node moves, it requires a reset of the data transmission path, which causes a lot of control messages and delays. In this paper, we propose a CMS(Cluster-based Mobile Sink) method to support the movement of mobile sink in a cluster sensor environment. The proposed scheme minimizes an amount of control messages without resetting the routing paths of entire sensor networks by supporting the sink mobility path using the neighbor cluster list. And, it simplifies the routing path setup process by setting a single hop path between clusters without a gateway. The experiment results show that the proposed scheme has superior energy efficiency in processing and network structure, compared with existing clustering and mesh routing protocols.

• Journal of the Korea Society for Simulation
• /
• v.15 no.4
• /
• pp.107-117
• /
• 2006

Wireless Sensor Network consists of sensor nodes and sink. A sink receives and processes signals created from sensor nodes. Many studies have been performed, since sensor network allows multiple nodes to run using a limited amount of energy, Most researches have focused on using fixed sink. However, in many cases, the sink has mobility effected by man, cars, and etc. This research proposes three methods for reducing the node's energy consumption which is applied the Grid method based on mobile sink. Most routing processes handled by the mobile sink and wireless sensor area is separated and operated respectively. So, this research allows decreasing the power costs. In addition, it also proposes methods using simulation to test the quality of the performance.

• Journal of the Semiconductor & Display Technology
• /
• v.15 no.3
• /
• pp.12-17
• /
• 2016

In this study, numerical simulations for the conjugate heat transfer of air with a heat-sink of CPU were conducted. The heat-sink consisted of many fins of cylinder shape and the effect of the number of fins on the cooling performance of the heat sink was investigated. Grid independent solutions were obtained to compare the maximum temperature of the heat-sink for various conditions. It was found that maximum temperature of the heat-sink asymptotically approached 310K as the number of fins went to infinity. The energy exchange of air with the heat-sink was found to be nearly independent on the number of fins.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.182-187
• /
• 2006

This research presented the heat resistance characteristics of heat sink which is newly designed through the experiment. For the same volume and base plate of heat sinks, the experiment of heat transfer characteristics was conducted for forced convection of layered type heat sink. The heat transfer and pressure drop characteristics of the layered type heat sink were compared for the various kinds of fin pitches, fin heights and heights of heat sink. The results show that thermal resistance is decreased as the height of heat sink increases and the fin height and fin pitch decrease, From the experimental data of layered type heat sink, the correlation equation of Nusselt number was obtained as follows ; $$Nu=0.845{\cdot}Re^{0.393}{\cdot}(\frac{f_h}{D_h})^{0.160}{\cdot}(\frac{f_p}{D_h})^{0.372}{\cdot}(\frac{H_{hs}}{D_h})^{-0.942}$$

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.6
• /
• pp.1490-1500
• /
• 1995

Compression molding of SMC (Sheet Molding Compound) in a thin plaque with substructures like a rib is involved with the formation of surface defect along the centerline over the rib area called by sink mark depending on process parameters. The surface quality of the external panels in automotive manufacturing is so critical that this kind of defect should be eliminated during manufacturing stages. The effect of process parameters on sink mark formation and the distribution of chopped fiberglasses in the compression molded thin plaque with a rib was experimentally investigated in the present study. In order to estimate the effect of the molding parameters such as molding temperature, mold closing speed, depth of the rib, corner radius of the rib, and final molded part thickness of flat portion on the depth of sink mark and the distribution of fiberglasses in the molded SMC part with the rib under the present experimental conditions, the molding parameters used in experiments were non-dimensionalized equation for predicting the depth of sink mark was determined through dimensional analysis based on the experimental data. The orientation and distribution of fiberglasses and fillers which directly affect the formation and depth of sink mark were investigated by taking the photographs of the cross-sectional area of the molded specimen using scanning electron microscope. The experimental results proposed from this investigation are useful in understanding the formation of sink mark and predicting the depth of sink mark in compression molding of SMC with substructures.

• Journal of Korean Society for Atmospheric Environment
• /
• v.31 no.1
• /
• pp.72-82
• /
• 2015

We constructed greenhouse gas (GHG) and air pollution (AP) integrated sink/emission inventories and evaluated the environmental value for the vegetation sector in Seoul during year 2010. The data of vegetation, classified into four sectors of cultivated land, forest land, park and street tree, were obtained from Statistics Korea and Seoul City. Based on the previous studies, only $CO_2$ was chosen as GHG sink by vegetation. $NO_2$ and $SO_2$ were chosen as AP sink by vegetation, while isoprene, monoterpene, other VOC (OVOC) and NH3 were chosen as AP emission from vegetation. Estimation methodology and sink/emission factors were gathered from reports and published literatures. Estimated GHG sink by vegetation during year 2010 was 12,987,173 $tonCO_{2eq}$, of which approximately 1/4 was from pure vegetation and the remaining 3/4 from vegetation soil. AP sink and emission were estimated to be 23,309 tonAP and 2,629,797 tonAP, respectively. The analysis by administrative districts in Seoul revealed that among 25 districts, Seocho-gu, Nowon-gu, Eunpyeong-gu, Gwanak-gu and Gangbuk-gu were the major districts in GHG and AP sink/emission inventories for vegetation sector. Environmental value of vegetation as a function of GHG and AP sink, was estimated as 800 billion won, corresponding to 5% of the total cost of the forest land in Korea evaluated as a public function.

• Journal of KIISE:Information Networking
• /
• v.37 no.3
• /
• pp.204-216
• /
• 2010

Since Sensor nodes around a fixed sink have huge concentrated network traffic, the battery consumption of them is increased extremely. Therefore the lifetime of sensor networks is limited because of huge battery consumption. To address this problem, a mobile sink has been studied for load distribution among sensor nodes. Since a mobile sink changes its location in sensor networks continuously, the mobile sink has time limits to communicate with each sensor node and unstable signal strength from each sensor node. Therefore, a fair and stable data collection method between a mobile sink and sensor nodes is necessary in this environment. When some sensor nodes are not able to send data to the mobile sink, a real-time application in sensor networks cannot be provided. In this paper, the new scheduling method, FQMS (Fair Queuing for Mobile Sink), is proposed for fair and stable data collection for mobile sinks in sensor networks. The FQMS guarantees balanced data collecting between sensor nodes for a mobile sink. In out experiments, the FQMS receives more packets from sensor nodes than legacy scheduling methods and provides fair data collection, because moving speed of a mobile sink, distance between a mobile sink and sensor nodes and the number of sensor nodes are considered.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.217-220
• /
• 2007

The quality of product depends on a lots of injection molding conditions at each operation stage and mainly was effected by pressure and temperature. The objective of this study was to investigate the relationship between the product quality and the distribution of pressure in a cavity with operation condition change. Specimen having some ribs was designed and the mold was prepared and temperature and pressure sensors were installed in the mold. PP was used and pressure distribution was measured with operation condition change. The relationship between the sink mark and the pressure in a cavity was investigated by measurement of the level of sink mark. The level of sink mark was decreased at the cross of plane and rib by increasing of pressure in a cavity, so the pressure should be controlled properly in order to get the required quality.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.05b
• /
• pp.155-158
• /
• 2005

수자원 분야에서 DEM은 유역을 분할하고 하천망을 생성하며 유역 범위 내에서 지형인자를 계산하는 과정에서 광범위하게 이용되고 있다. 그러나 수치지도의 등고선이나 영상으로부터 추출된 DEM은 sink나 flat area와 같은 오류를 다수 포함하고 있으며, 이러한 오류들을 합리적인 방법으로 제거하는 과정이 필요하다. 본 연구에서는 DEM에서의 sink를 제거하기 위하여 breaching 알고리즘(Grabercht와 Martz, 1996)을 포함하는 filling method(Jenson과 Domingue, 1988; Martz와 Jong, 1988)를 이용하였으며, flat area를 처리하기 위해서는 combined gradient method(Grabercht와 Martz, 1996)를 이용하였다. 또한 흐름방향을 결정하기 위해서는 8방향법(O'Callaghan과 Mark, 1984)을 이용하였다. 이러한 방법을 통하여 보정된 DEM을 이용하여 흐름방향과 흐름누적수를 계산한 후 하천망을 추출하였다. 추출된 하천망은 ArcView 3.2a와 TOPAZ v3.1을 적용한 WMS v6.1에서의 결과와 비교하였으며, DEM의 오류수정을 위한 알고리즘이 적절히 구현된 것을 확인 할 수 있었다. 따라서 본 연구에서 개발한 DEM 보정기술은 DEM을 수자원 분야에 이용하기 위해 필요한 sink와 flat area 처리를 효과적으로 수행할 수 있는 것으로 나타났다.