• Journal of Mechanical Science and Technology
• /
• v.17 no.5
• /
• pp.629-636
• /
• 2003

This paper introduces the developed geometry PIG (Pipeline Inspection Gauge), one of several ILI (In-Line Inspection) tools, which provide a full picture of the pipeline from only single pass, and has compact size of the electronic device with not only low power consumption but also rapid response of sensors such as calipers, IMU and odometer. This tool is equipped with the several sensor systems. Caliper sensors measure the pipeline internal diameter, ovality and dent size and shape with high accuracy. The IMU (Inertial Measurement Unit) measures the precise trajectory of the PIG during its traverse of the pipeline. The IMU also provide three-dimensional coordination in space from measurement of inertial acceleration and angular rate. Three odometers mounted on the PIG body provide the distance moved along the line and instantaneous velocity during the PIG run. The datum measured by the sensor systems are stored in on-board solid state memory and magnetic tape devices. There is an electromagnetic transmitter at the back end of the tool, the transmitter enables the inspection operators to keep tracking the tool while it travels through the pipeline. An experiment was fulfilled in pull-rig facility and was adopted from Incheon LT (LNG Terminal) to Namdong GS (Governor Station) line, 13 km length.

• The KIPS Transactions:PartA
• /
• v.8A no.2
• /
• pp.157-166
• /
• 2001

A simulation package has been developed as an event-driven system that can handle the hardware configuration of STC104 and algorithm proposed in the sister paper of ‘Study on High Speed Routers(II).’After various STC104 topology of meshes, torus, and hypercubes are constructed using up to 512 switches, the performance of each topology has been analyzed under different message generation rate in terms of throughputs, latency, and packet blocking time. Modified multicast algorithms for STC104 have been proposed for STC104 after U-mesh and U-torus in order to overcome the multicasting difficulty because of the point-to-point communication method found in STC104. The performance of the multicast algorithms have been analyzed over meshes and torus configuration. Throughput gets higher in the order of mesh, torus, and hypercube. Throughput difference among topology were distinctive in the zone of high message generation rate. Latency and blocking time increased in the order of hypercube, torus, and mesh. U-mesh and U-torus of software multicast showed similar throughput, however, U-mesh peformed slightly better result. These algorithms showed eight to ten times better results compared to individual message pass for 90 destination nodes. Multi-link environment also showed better performance than single-link environment because multi-link network used the extra links for communication.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.12 no.6
• /
• pp.621-633
• /
• 1987

In this paper, for the purpose of constructing LAN(Local Area Network) with Token ring type Star-wired ring method, we implemented an in board network adapter and a concentrator using microprocessor. Using cconcentrato's communication controlling function, the concentator prevents a break of communication by by-passing the fault network adapter. Because, in the data transfer period, a concentrator recognized the network adapter at transmit and receiving side to construct single by -pass line and reduces ring latency time at both sides, this method can keep a high throughput in high and low load. Being considered the result of performance evaluation for the method our study employed, high throughput can be obtained.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.11 no.1
• /
• pp.53-60
• /
• 2015

This study was investigated to develop process technology of laser cladding with austenite stainless steel for Weld Inlay repair of dissimilar metal weld in reactor vessel in/outlet nozzles. Weld Inlay experiments were performed by laser cladding repair system consisting of common manipulator, laser apparatus and welding process scheduler, etc. Single pass welding experiments were conducted in order to obtain the optimum welding process parameters for filler wires of ER309L and Alloy 52M before multi-layer laser cladding. Based on the above obtained results, multi-layer laser cladding experiments were carried out, and welding qualities for weld specimens were estimated by PT, OM, SEM and EDS analysis. Consequently, it was revealed that multi-layer laser cladding on austenite stainless steel using filler wires of ER309L and Alloy 52M could be possible to meet ASME Code standard without any weld defect.

• Journal of Biomedical Engineering Research
• /
• v.23 no.6
• /
• pp.477-484
• /
• 2002

A pacemaker autosense algorithm with dual thresholds. one for noise or tachyarrhythmia detection (noise threshold, NT) and the other for intrinsic beat detection (sensing threshold. ST), was developed to improve the sensing performance in single pass VDD electrograms. unipolar electrograms, or atrial fibrillation detection. When a deflection in an electrogram exceeds the NT (defined as 50% of 57), the autosense algorithm with dual thresholds checks if the deflection also exceeds the ST. If it does, the autosense algorithm calculates the signal to noise ratio (SNR) of the deflection to the highest deflection detected by NT but lower than ST during the last cardiac cycle. If the SNR 2, the autosense algorithm declares an intrinsic beat detection and calculates the next ST based on the three most recent intrinsic peaks. If the SNR $\geq$2, the autosense algorithm checks the number of deflections detected by NT during the last cardiac cycle in order to determine if it is a noise detection or tachyarrhythmia detection. Usually the autosense algorithm tries to set the 57 at 37.5% of the average of the three intrinsic beats, although it changes the percentage according to event classifications. The autosense algorithm was tested through computer simulation of atrial electrograms from 5 patients obtained during EP study, to simulate a worst sensing situation. The result showed that the ST levels for autosense algorithm tracked the electrogram amplitudes properly, providing more noise immunity whenever necessary. Also, the autosense algorithm with dual thresholds achieved sensing performance as good as the conventional fixed sensitivity method that was optimized retrospectively.

• Transactions of Materials Processing
• /
• v.18 no.5
• /
• pp.410-415
• /
• 2009

Experimental and numerical studies were performed to examine the effect of material temperature and reduction ratio on friction coefficient during hot flat rolling. We carried out a single pass pilot hot flat rolling test at the temperatures range of $900{\sim}1200^{\circ}C$ and measured the spread of deformed material while reduction ratio varied from 20% to 40%. Materials used in this study were a high carbon steel and two alloy steels. The dimension of specimen used in hot rolling experiment was $50mm{\times}50mm{\times}300mm$. We performed a series of finite element simulation of the hot rolling process to compute the friction coefficient change in terms of steel grade and reduction ratio. Results showed that temperature dependency of friction coefficient is not noteworthy but the effect of reduction ratio on friction coefficient is quite large. For high carbon steel, friction coefficient at reduction ratio of 30% is lower than that at that of 20%. Meanwhile friction coefficient at reduction ratio of 40% was one and half times large compared with that at that of 20%. The effect of steel grade on friction coefficient was significant when reduction ration was large, e.g., 40%.

• Journal of Chest Surgery
• /
• v.19 no.4
• /
• pp.627-632
• /
• 1986

This report describes our 17-years experience with intracardiac repair in 123 patients older than 15 years with tetralogy of Fallot. Major clinical manifestation was cyanosis and clubbing [102 Pts], but other minor associated manifestation were infective endocarditis, pulmonary tuberculosis, brain abscess, congestive heart failure, nephrotic syndrome, and tuberculous spondylitis. Prior palliative shunts had been performed in 10 patients. Preoperative hemoglobin ranged from 9.7 gm/dl to 25 gm/dl [mean 19 gm/dl]. The type of ventricular septal defect were typical perimembranous type, and total canal defect [13%]. The right ventricular outflow tract obstruction was due to combined [58.5%], infundibular [35%], and valvular stenosis [6.5%]. Transannular patch was used in 17% of patients. Hospital mortality was 9.8% in overall, but decreased to 1.7% since 1982. There was two late death [12 year actuarial survival [97%] due to fulminant hepatitis, residual abnormalities [PS, VSD]. Ninety two percent of survivors at follow-up are asymptomatic and leading an active normal life. Residual ventricular septal defect was detected with radionuclide single pass study in 15.3% of patients but almost cases were Qp/Qs less than 1.5, and only two patients had been candidates for reoperation.

• Journal of Embryo Transfer
• /
• v.32 no.4
• /
• pp.305-310
• /
• 2017

Miniature pig (minipig) has been considered as an important laboratory animal in the developmental biotechnology researches with respect to xenotransplantation, stem cell, somatic cell nuclear transfer and embryo transfer. Given that the laboratory minipigs are normally housed at an indoor facility, they pass the time with lying or sleeping unless it is feeding time. Therefore, it is necessary to provide environmental enrichments to satisfy their innate needs and to lessen atypical behaviors caused by stress, on the purpose of welfare. We quantitatively investigated the type of preferable enrichment for the laboratory minipigs as well as its effect on their daily life. They presented a great interest to the pliable pail but a rapid loss of attraction to non-preferable enrichments. When the daily life of the single housed minipigs was quantified based on duration of playing or resting, they were more actively engaged in lively activities in the presence of enrichments. In addition, the provision of enrichments could effectively alleviate the conflicts during group housing when new pen mate was introduced, resulting in reduction of wound cases. We believe the considerations of animal welfare are essential to the conduct of better research because animals in the non-stressful environment will be more physiologically stable and provide more reliable results in the animal experiments.

• Korean Journal of Optics and Photonics
• /
• v.9 no.4
• /
• pp.264-269
• /
• 1998

The Measurement of concentration patterns for $C_2$, CH and OH radicals in the premixed propane-air flame could be managed through an image processing technique. This technique was applied to the three kinds of flames on a bunsen burner-mixtures of fuel to be lean, optimum and excessive respectively. The image processing system was complished by treating single wavelength flame images around the eac radical luminescence band, which was obtained by using a set of narrow band pass filters, an image intensifier, CCD and PC. It was possible to observe and predict the reaction zone and the concentration distribution of the radicals, Spatial distribution of each radicals in the raaction zone gave us enough informations to analyze the reaction mechanisms in $C_mH_n$ combustion process. According to this informations, the image of $C_2$ radical exists at front zone, following the images of CH and OH radicals at downstream.

• Transactions of Materials Processing
• /
• v.20 no.6
• /
• pp.439-449
• /
• 2011

The temperature distribution and subsequent permanent deformation of SS400 carbon steel plate subjected to an induction-based line heating process were studied by a numerical method involving coupled 3-D electromagnetic-thermal-structural analysis. The numerical study revealed that the amount of permanent deformation is strongly related to the Joule loss caused by such process conditions as input power and moving speed of the heat source. To validate the numerical analysis results, line heating experiments were carried out with a high frequency(HF) induction heating(IH) equipment capable of bending thick plate with the moving accuracy of ${\pm}0.1mm$ in heating coil position. The amount of permanent deformation increased with decreasing moving speed and increasing input power.