• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.12
• /
• pp.3235-3245
• /
• 1996

A DDFS(Direct Digital Frequency Synthesizer) used in spread spectrum communication systems must need fast switching speed, high resolution(the step size of the synthesizer), small size and low power. The chip has been designed with four parallel sine look-up table to achieve four times throughput of a single DDFS. To achieve a high processing speed DDFS chip, a 24-bit pipelined CMOS technique has been applied to the phase accumulator design. To reduce the size of the ROM, each sine ROM of the DDFS is stored 0-.pi./2 sine wave data by taking advantage of the fact that only one quadrant of the sine needs to be stored, since the sine the sine has symmetric property. And the 8 bit of phase accumulator's output are used as ROM addresses, and the 2 MSBs control the quadrants to synthesis the sine wave. To compensate the spectrum purity ty phase truncation, the DDFS use a noise shaper that structure like a phase accumlator. The system input clock is divided clock, 1/2*clock, and 1/4*clock. and the system use a low frequency(1/4*clock) except MUX block, so reduce the power consumption. A 107MHz DDFS(Direct Digital Frequency Synthesizer) implemented using 0.8.mu.m CMOS gate array technologies is presented. The synthesizer covers a bandwidth from DC to 26.5MHz in steps of 1.48Hz with a switching speed of 0.5.mu.s and a turing latency of 55 clock cycles. The DDFS synthesizes 10 bit sine waveforms with a spectral purity of -65dBc. Power consumption is 276.5mW at 40MHz and 5V.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.6
• /
• pp.60-67
• /
• 2008

A low-power 2.4GHz fractional-N frequency synthesizer has been designed for 2.4GHz ISM band applications such as Bluetooth, Zigbee, and WLAN. To achieve low-power characteristic, the design has been focused on the power optimization of power-hungry blocks such as VCO, prescaler, and ${\Sigma}-{\Delta}$ modulator. An NP-core type VCO is adopted to optimize both phase noise and power consumption. Dynamic D-F/Fs with no static DC current are employed in designing the low-power prescaler circuit. The ${\Sigma}-{\Delta}$ modulator is designed using a modulus mapping circuit for reducing hardware complexity and power consumption. The designed frequency synthesizer which was fabricated using a $0.18{\mu}m$ CMOS process consumes 7.9mA from a single 1.8V supply voltage. The experimental results show that a phase noise of -118dBc/Hz at 1MHz offset, the reference spur of -70dBc at 25MHz offset, and the channel switching time of $15{\mu}s$ over 25MHz transition have been achieved. The designed chip occupies an area of $1.16mm^2$ including pads where the core area is only $0.64mm^2$.

• Journal of Broadcast Engineering
• /
• v.17 no.5
• /
• pp.742-755
• /
• 2012

In this paper, we propose a parallel deblocking algorithm to resolve workload imbalance when the deblocking filter of high efficiency video coding (HEVC) decoder is parallelized. In HEVC, the deblocking filter which is one of the in-loop filters conducts two-step filtering on vertical edges first and horizontal edges later. The deblocking filtering can be conducted with high-speed through data-level parallelism because there is no dependency between adjacent edges for deblocking filtering processes. However, workloads would be imbalanced among regions even though the same amount of data for each region is allocated, which causes performance loss of decoder parallelization. In this paper, we solve the problem for workload imbalance by predicting the complexity of deblocking filtering with coding unit (CU) depth information at a coding tree block (CTB) and by allocating the same amount of workload to each core. Experimental results show that the proposed method achieves average time saving (ATS) by 64.3%, compared to single core-based deblocking filtering and also achieves ATS by 6.7% on average and 13.5% on maximum, compared to the conventional uniform data-level parallelism.

• The Journal of Internal Korean Medicine
• /
• v.41 no.2
• /
• pp.194-203
• /
• 2020

Objectives: This study aimed to compare the gait patterns of cerebellar infarction patients with those of corticospinal tract stroke patients through a follow-up of patients with ataxic gait due to cerebellar infarction and corticospinal tract stroke. Methods: We investigated two cases of patients with cerebellar infarction and two cases each of acute or chronic corticospinal tract stroke who were hospitalized at Wonkwang University Gawangju Medical Center from September 1, 2017 to February 15, 2020 based on medical records and gait analyses. The spatiotemporal gait parameters of each patient were measured three times at 2-week intervals except those of the chronic corticospinal tract stroke patients, which were measured twice at a 1-month interval. Results: Spatiotemporal gait parameters, which include velocity, cadence, step length, stride length, and single support, were consistently increased in the cerebellar infarction patients in comparison to the corticospinal tract stroke patients. The stance phase was decreased in all the patients. Conclusions: The cerebellar infarction patients' gait spatiotemporal parameters were found to consistently improve. Moreover, gait analysis can be used to effectively measure improvement of ataxic gait.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.9
• /
• pp.825-837
• /
• 2017

This paper describes a novel type of a walking rehabilitation robot that applies robot technologies to crutches used by patients with walking difficulties in the lower body. The primary features of the developed robot are divided into three parts. First, the developed robot is worn on the patient's chest, as opposed to the conventional elbow crutch that is attached to the forearm; hence, it can effectively disperse the patient's weight throughout the width of the chest, and eliminate the concentrated load at the elbow. Furthermore, it allows free arm motion during walking. Second, the developed robot can recognize the walking intention of the patient from the magnitude and direction of the ground reactive forces. This is done using three-axis force sensors attached to the feet of the robot. Third, the robot can perform a stair walking function, which can change vertical movement trajectories in order to step up and down a single stair according to the floor height. Consequently, we experimentally showed that the developed robot can effectively perform walking rehabilitation assistance by perceiving the walking intention of the patient. Moreover we quantitatively verified muscle power assistance by measuring the electromyography (EMG) signals of the muscles of the lower limb.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.36S no.8
• /
• pp.88-100
• /
• 1999

Detecting human face and facial landmarks automatically in an image is as essential step to a fully automatic face recognition system. In this paper, we present a new approach to detect automatically face and its eyes of input image with scale and rotation variations of faces by using an intensity based template matching with a single log-polar face template. In a template-based matching it is necessary to normalize the scale changes and rotations of an input image to a template ones. The log-polar mapping which simulates space-variant human visual system converts scale changes and rotations of input image into constant horizontal and cyclic vertical shifts in the output plane. Intelligent use of this property allows us to shift of the candidate log-polar faces mapped at various fixation points of an input image to be matched to a template over the log-polar plane. Thus, the proposed method eliminates the need of adapting multitemplate and multiresolution schemes, which inevitably give rise to intensive computation involved to cope with scale and rotation variations of faces. Through this scale and rotation involved to cope with scale and method can lead to detecting face and its eyes simultaneously. Experimental results on a database of 795 images show over 98% detection rate.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.5
• /
• pp.62-70
• /
• 2007

In this paper, the boost Power Factor Correction(PFC) technique for Direct Torque Control(DTC) of brushless DC motor drive in the constant torque region is implemented on a TMS320F2812DSP. Unlike conventional six-step PWM current control, by properly selecting the inverter voltage space vectors of the two-phase conduction mode from a simple look-up table at a predefined sampling time, the desired quasi-square wave current is obtained, therefore a much faster torque response is achieved compared to conventional current control. Furthermore, to eliminate the low-frequency torque oscillations caused by the non-ideal trapezoidal shape of the actual back-EMF waveform of the BLDC motor, a pre-stored back-EMF versus position look-up table is designed. The duty cycle of the boost converter is determined by a control algorithm based on the input voltage, output voltage which is the dc-link of the BLDC motor drive, and inductor current using average current control method with input voltage feed-forward compensation during each sampling period of the drive system. With the emergence of high-speed digital signal processors(DSPs), both PFC and simple DTC algorithms can be executed during a single sampling period of the BLDC motor drive. In the proposed method, since no PWM algorithm is required for DTC or BLDC motor drive, only one PWM output for the boost converter with 80 kHz switching frequency is used in a TMS320F2812 DSP. The validity and effectiveness of the proposed DTC of BLDC motor drive scheme with PFC are verified through the experimental results. The test results verify that the proposed PFC for DTC of BLDC motor drive improves power factor considerably from 0.77 to as close as 0.9997 with and without load conditions.

• Management & Information Systems Review
• /
• v.23
• /
• pp.25-40
• /
• 2007

In the highly competitive and divers world of financial market, customer is the single most important factor to company's survival. Especially, creating a relationship with valued customers is a key to success. CRM provides the mean to retain high value customers. It takes a prospect of what customers expect. Utilizing those knowledge can help the products and service meet the customers' needs, thereby maximizing customer satisfaction and company's profit. In this report, I am going to suggest a few ways to develop successful CRM in the life insurance industry. First, CRM should innovate the way of communication to keep pace with Web 2.0 era. In other words, the customer's needs should be caught by real-time communication than traditional off-line market research. Thus, the functionality and specification of products can be decided by customer's direct choice so that the customers are able to purchase the understanding and experience of the products. Second, CRM project should consider whether the initial strategy plan can promise the stable growth of customer at the first step. When planning strategy, the project needs to identify what customer wants and how to fulfill the needs with stable growth of the customer. In addition, the CRM should be developed by realizing that customer centric benefits ultimately guarantee the growth of the organization. Third, CRM systems should enhance the organization's ability to take the customer's insight in a 360 degree view and to capture the voice of the customer directly. In order to develop the best matched product package, more precise customer segmentation should be ahead of market segmentation strategy. Forth, the biggest reward from CRM will be a customer royalty program. Many successful banks are already planning and practicing customer royalty strategy. A comprehensive analysis of customers and their behavior allow organization to identify high value potential customers' needs and determine a strategy required to meet those needs. Even life insurance companies such as Prudential Korea are developing products designed for royal customers. Fifth, understanding and managing the experience of customer called Customer Experience Management also can increase customer satisfaction. Measuring only customers' experience and adapting it to marketing strategy make products position in the gap between the customers' expectation and experience not required by market. A key component of CEM is its application across all organizational functions. At last, the direction of change and development of CRM can be defined from the conceptualization of information technology represented by Ubiquitous and Web 2.0. Instead of just managing customer information, companies should take the initiative in personalized system with customer oriented strategy. Furthermore, with the regular communication between CRM stakeholders (Sales-Marketing-IT), customer's demand should be directly reflected to enterprise strategy in real time.

• Korean Journal of Plant Tissue Culture
• /
• v.27 no.6
• /
• pp.453-459
• /
• 2000

Three rice (Oryza sativa L. var Dong-Jin) mutants (DTR1, DTR2, DTR3) resistant to S-methyltryptophan (5MT) were selected by mutagenized M3 seeds. The frequency of chlorophyll mutations induced by the EMS (0.2%) treatment performed 2 hours after flowering is clearly higher than that induced by other treatments in M1 generation. Progeny obtained from the self-pollinating of 5MT-resistant lines segregated with 3 : 1 of resistant to sensitive ratio. Furthermore, the ratio of homozygote to heterozygote in 5MT-resistant plants of the M4 generation was 1：2. These results show that 5MT resistance was inherited as a single dominant nuclear gene. The resistance was also expressed in callus derived from seeds. Total free amino acid content in homozygous seeds of DTR1 and DTR2 showed about 1.7 fold-increased compared to the wild-type seeds. In particular, the levels of phenylalanine and Iysine were, respectively, 6.2 and 3.2 times higher than those in the wild-type seeds. However, seeds of DTR3 had lower levels of free amino acid than the wild-type seeds. This result indicate that these mutants as a significant step towards the production of new rice with balanced amino acid content.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.363-363
• /
• 2014

Ruthenium (Ru) has attractive material properties due to its promising characteristics such as a low resistivity ($7.1{\mu}{\Omega}{\cdot}cm$ in the bulk), a high work function of 4.7 eV, and feasibility for the dry etch process. These properties make Ru films appropriate for various applications in the state-of-art semiconductor device technologies. Thus, it has been widely investigated as an electrode for capacitor in the dynamic random access memory (DRAM), a metal gate for metal-oxide semiconductor field effect transistor (MOSFET), and a seed layer for Cu metallization. Due to the continuous shrinkage of microelectronic devices, better deposition processes for Ru thin films are critically required with excellent step coverages in high aspect ratio (AR) structures. In these respects, atomic layer deposition (ALD) is a viable solution for preparing Ru thin films because it enables atomic-scale control of the film thickness with excellent conformality. A recent investigation reported that the nucleation of ALD-Ru film was enhanced considerably by using a zero-valent metallorganic precursor, compared to the utilization of precursors with higher metal valences. In this study, we will present our research results on the synthesis and characterization of novel ruthenium complexes. The ruthenium compounds were easy synthesized by the reaction of ruthenium halide with appropriate organic ligands in protic solvent, and characterized by NMR, elemental analysis and thermogravimetric analysis. The molecular structures of the complexes were studied by single crystal diffraction. ALD of Ru film was demonstrated using the new Ru metallorganic precursor and O2 as the Ru source and reactant, respectively, at the deposition temperatures of $300-350^{\circ}C$. Self-limited reaction behavior was observed as increasing Ru precursor and O2 pulse time, suggesting that newly developed Ru precursor is applicable for ALD process. Detailed discussions on the chemical and structural properties of Ru thin films as well as its growth behavior using new Ru precursor will be also presented.