• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.2B no.3
• /
• pp.115-124
• /
• 2002

This paper presents an active auxiliary edge-resonant DC link snubber with a ringing surge damper and a three-phase voltage source type zero voltage soft-switching inverter with the resonat snubber treated here for the AC servo motor driver applications. The operation of the active auxiliary edge-resonant DC link snubber circuit with PWM voltage is described, together with the practical design method to select its circuit parameters. The three-phase voltage source type soft-switching inverter with a single edge-resonant DC link snubber treated here is evaluated and discussed for the small-scale permanent magnet (PM) type-AC servo motor driver from an experimental point of view. In addition to these, the AC motor stator current and its motor speed response for the proposed three-phase soft-switching inverter employing Intelligent Power Module(IPM) based on IGBTS are compared with those of the conventional three-phase hard-switching inverter using IPM. The practical effectiveness of the three-phase soft-switching inverter-fed permanent magnet type AC motor speed tracking servo driver is proven on the basis of the common mode current in a novel type three-phase soft-switching inverter-fed AC motor side and the conductive noise on the mains terminal interface voltage as compared with those of the conventional three-phase hard-switching inverter-fed permanent magnet type AC servo motor driver for the speed tracking applications.

• Journal of the Korean Vacuum Society
• /
• v.19 no.5
• /
• pp.377-384
• /
• 2010

Many routes have been developed for the synthesis of signle-walled carbon nanotubes (SWCNTs). We spun fibers of SWCNTs directly from vertical furnace using a liquid source of carbon and an iron-contained molecule. The solution was prepared by ethanol as a carbon source, in which ferrocene as a catalyst, thiophene were dissolved. It was then injected from the top of the furnace into hot zone with hydrogen as a carrier gas. We successfully synthesized high-quality SWCNTs by adjusting the various experimental conditions, such as concentration of ferrocene, solution injection rate, concentration of thiophene, and hydrogen flow rate. Measurement of Raman spectroscopy, scanning electron microscopy, and transmission electron microscopy were carried out to find the optimized conditions. The synthesized SWCNTs (1.16~1.64 nm) appeared a bundle structure and well-aligned parallel to the direction of furnace. These results also provide an simple way for high-quality SWCNTs mass production and fabricating direct spining SWCNTs fiber. It will allow one-step production of SWCNTs fiber with potentially excellent properties and wide-range applications.

• Horticultural Science & Technology
• /
• v.30 no.6
• /
• pp.686-693
• /
• 2012

To develop a technique for mass-propagation of virus-free sweet potato [Ipomoea batatas (L.) Lam.] plant using nutrient film technique (NFT), the growth characteristics of 4 cultivars as affected by nutrient solution composition and cutting size were investigated. 72 cells (35 mL/cell) plug trays filled with vermiculite and perlite (1:1, v/v) were used. Vine length, fresh and dry weights of virus-free plants were the greatest in the nutrient solution recommended by National Horticultural Research Station in Japan, followed by that recommended by National Institute of Horticultural & Herbal Science in Korea, and Yamazaki's nutrient solution for lettuce. The growth of uppershoot cuttings was the best among 4 subsections of cutting. Vine length, and fresh and dry weights increased in the longer cutting treatments, and were better in 'Shinzami' and 'Yeonhwangmi' than those in 'Mannami' and 'Shincheonmi'. Vine diameter and length of the longest root were not significantly affected by the cutting size and cutting source. The growth characteristics of the single node cutting were not significantly different from those in 2-node cutting. The efficiency of rapid mass-propagation could be promoted with single node cuttings and uppershoot cuttings grown in NFT system.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.7
• /
• pp.102-108
• /
• 2013

In manufacturing of solution-processed organic electronic devices, a spin coating method is frequently used, but which has a big problem. Solvent in a solution has a decisive effect such as physical and chemical damage for successive solution-based film deposition. Such a severe damage by solvent restricts for fabricating building blocks of multi-layered films from solutions. In this work, it will be shown that a proper combination of well-known solvents gives a chance to fabricate multi-layered film, also this new method was applied to make organic field effect transistor. Two types of bottom gate, bottom contact transistors were fabricated, one of which is fabricated by conventional single spin coating method, the other fabricated by double spin coating method. Compared with the electrical characteristics in a single spin coated transistor, the leakage current between source and gate electrode was decreased, ON state current was increased, and the extracted saturation mobility was multiplied more than 2.7 time for double spin coated transistors. It is suggested that the multiple coated gate dielectric structure is more desirable for high performance organic ferroelectric field effect transistors.

• IE interfaces
• /
• v.13 no.3
• /
• pp.378-387
• /
• 2000

As the globalization of manufacturing companies continues, the scope of dependence between these companies and distributors, and other suppliers are growing very rapidly since no one company manufactures or distributes the whole product by themselves. And, the need to increase the efficiency of the whole supply chain is increasing. This paper deals with a multi-plant lot-sizing problem(MPLSP) which happens in a decentralized manufacturing system of a supply chain. In this study, we assume that the whole supply chain is driven by a single source of independent demand and many levels of dependent demands among manufacturing systems in the supply chain. We consider setup cost, transportation cost and time, and inventory holding cost as a decision factor in the MPLSP. The MPLSP is decomposed into two sub-problems: a planning problem of the whole supply chain and a lot-sizing problem of each manufacturing system. The supply chain planning problem becomes a pure linear programming problem and a Generalized Goal Decomposition method is used to solve the problem. Its result is used as a goal of the lot-sizing problem. The lot-sizing problem is solved using the CPLEX package, and then the coefficients of the planning problem are updated reflecting the lot-sizing solution. This procedure is repeated until termination criteria are met. The whole solution process is similar to Lagrangian relaxation method in the sense that the solutions are approaching the optimum in a recursive manner. Through experiments, the proposed closed-loop hierarchical planning and traditional hierarchical planning are compared to optimal solution, and it is shown that the proposed method is a very viable alternative for solving production planning problems of decentralized manufacturing systems and in other areas.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.26 no.5
• /
• pp.191-202
• /
• 2022

Markov envelope as a theoretical solution of the parabolic wave equation with Markov approximation for the von Kármán type random medium is studied and approximated with the convolution of two probability density functions (pdf) of normal and gamma distributions considering the previous studies on the applications of Radiative Transfer Theory (RTT) and the analysis results of earthquake records. Through the approximation with gamma pdf, the constant shape parameter of 2 was determined regardless of the source distance r_o. This finding means that the scattering process has the property of an inhomogeneous single-scattering Poisson process, unlike the previous studies, which resulted in a homogeneous multiple-scattering Poisson process. Approximated Markov envelope can be treated as the normalized mean square (MS) envelope for ground acceleration because of the flat source Fourier spectrum. Based on such characteristics, the path duration is estimated from the approximated MS envelope and compared to the empirical formula derived by Boore and Thompson. The results clearly show that the path duration increases proportionately to r_o^1/2-r_o², and the peak value of the RMS envelope is attenuated by exp (-0.0033r_o), excluding the geometrical attenuation. The attenuation slope for r_o≤100 km is quite similar to that of effective attenuation for shallow crustal earthquakes, and it may be difficult to distinguish the contribution of intrinsic attenuation from effective attenuation. Slowly varying dispersive delay, also called the medium effect, represented by regular pdf, governs the path duration for the source distance shorter than 100 km. Moreover, the diffraction term, also called the distance effect because of scattering, fully controls the path duration beyond the source distance of 300 km and has a steep gradient compared to the medium effect. Source distance 100-300 km is a transition range of the path duration governing effect from random medium to distance. This means that the scattering may not be the prime cause of peak attenuation and envelope broadening for the source distance of less than 200 km. Furthermore, it is also shown that normal distribution is appropriate for the probability distribution of phase difference, as asserted in the previous studies.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.48 no.2
• /
• pp.28-34
• /
• 2011

In previous reports, we investigated a selective assembly method of fabricating single-walled carbon nanotubes (SWCNTs) on a silicon-dioxide ($SiO_2$) surface by using only a photolithographic process. In this paper, we have fabricated field effect transistors (FETs) with SWCNT channels by using the technique mentioned above. Also, we have electrically measured gating effects of these FETs under different source-drain voltages ($V_{SD}$). These FETs have been fabricated for sensor applications. Photoresist (PR) patterns have been made on a $SiO_2$-grown silicon (Si) substrate by using a photolithographic process. This PR-patterned substrate have been dipped into a SWCNT solution dispersed in dichlorobenzene (DCB). These PR patterns have been removed by using aceton. As a result, a selectively-assembled SWCNT channels in FET arrays have been obtained between source and drain electrodes. Finally, we have successfully fabricated 4 FET arrays based on SWCNT-channels by using our simple self-assembly technique.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.31.1-31.1
• /
• 2009

Carbon nanotubes (CNTs) are attractive material because of their superior electrical, mechanical, and chemical properties. Furthermore, their geometric features such as a large aspect ratio and a small radius of curvature at tip make them ideal for low-voltage field emission devices including backlight units of liquid crystal display, lighting lamps, X-ray source, microwave amplifiers, electron microscopes, etc. In field emission devices for display applications, the phosphor anode is positioned against the CNT emitters. In most case, light generated from the phosphor by electron bombardment passes through the anode front plate to reach observers. However, light is produced in a narrow depth of the surface of the phosphor layer because phosphor particles are big as much as several micrometers, which means that it is necessary to transmit through the phosphor layer. Hence, a drop of light intensity is unavoidable during this process. In this study, we fabricated a transparent cathode back plate by depositing an ultra-thin film of single walled CNTs (SWCNTs) on an indium tin oxide (ITO)-coated glass substrate. Two types of phosphor anode plates were employed to our transparent cathode back plate: One is an ITO glass substrate with a phosphor layer and the other is a Cr-coated glass substrate with phosphor layer. For the former case, light was radiated from both the front and the back sides, where luminance on the back was ~30% higher than that on the front in our experiments. For the other case, however, light was emitted only from the cathode back side as the Cr layer on the anode glass rolled as a reflecting mirror, improving the light luminance as much as ~60% compared with that on the front of one. This study seems to be discussed about the morphologies and field emission characteristics of CNT emitters according to the experimental parameters in fabricating the lamps emitting light on the both sides or only on the cathode back side. The experimental procedures are as follows. First, a CNT aqueous solution was prepared by ultrasonically dispersing purified SWCNTs in deionized water with sodium dodecyl sulfate (SDS). A milliliter or even several tens of micro-liters of CNT solution was deposited onto a porous alumina membrane through vacuum filtration. Thereafter, the alumina membrane was solvated with the 3 M NaOH solution and the floating CNT film was easily transferred to an ITO glass substrate. It is required for CNT film to make standing CNTs up to serve as electron emitter through an adhesive roller activation.

• Horticulture, Environment, and Biotechnology : HEB
• /
• v.59 no.6
• /
• pp.805-813
• /
• 2018

Vanda is an aerial tropical orchid native to Thailand and nitrogen (N) fertilizer is mainly used to promote its growth and quality. However, little is known about the characteristics of N absorption and assimilation in Vanda. The objective of this study was to determine the appropriate source of N for Vanda cultivation. In this experiment, shoots and roots of Vanda 'Ratchaburi Fuchs-Katsura' were sprayed weekly with 100 ml of $^{15}N$ tracer solution (1) 10 mM of $^{15}NO_3{^-}$, (2) 5 mM of $^{15}NO_3{^-}$ plus 5 mM of $NH_4{^+}$, (3) 5 mM of $NO_3{^-}$ plus 5 mM of $^{15}NH_4{^+}$ and (4) 10 mM of $^{15}NH_4{^+}$. The results indicated that plants fed with a combined N fertilizer gave the highest of $^{15}N$ use efficiency ( $^{15}NUE$) of about 21.8%, 30 days after the first feeding (DAF), compared with those fed sole sources of $^{15}NO_3{^-}$ (21.0%) and $^{15}NH_4{^+}$ (16.6%). However, a sole nitrate fertilizer or combination fertilizer did not significantly affect the total N and labelled N content. Alanine was a major amino acid found in leaves and roots at 7 DAF, whereas glutamine was mainly found in stems. At 30 DAF, tyrosine and alanine became major components in the leaves, and glutamine decreased in stems when plants were fed with a single $^{15}NH_4{^+}$ source.

• 한국연소학회:학술대회논문집
• /
• 1997.06a
• /
• pp.61-68
• /
• 1997

The morphology and size distribution of chromium oxides and the concentration measurement of atomic arsenic have been studied in laminar diffusion flames. Nitrogen was added to vary flame temperatures in hydrogen flames. Ethene flames were used in order to investigate the potential for interaction between the soot aerosol that is formed in these flames and the chromium aerosol. Two sources of chromium compounds were introduced: chromium nitrate and chromium hexacarbonyl. A detailed investigation of the morphology was carried out by scanning electron microscopy (SEM). The amounts of Cr(VI) and total Cr were determined by a spectrophotometric method and by X-ray fluorescence spectrometry, respectively. Also, LIF was used for the measurement of atomic arsenic, which was excited at 197.2 nm and was detected at 249.6 nm. Results showed that the morphology of the particles varied with the flame temperature and with the chromium source. The particles were characterized by porous structures, cenospheres and agglomerated dense particles when chromium nitrate solution was added to the flames. At low to moderate temperatures, porous sintered cenospheric structures were formed, in some cases with a blow hole. At higher temperatures, an agglomerated cluster which was composed of loosely sintered submicron particles was observed. It was also found that the emission of Cr(VI) from the undiluted $H_2$ flame was more than 10 times larger than in the 50% $H_2$ / 50% $N_2$ flame on a mass basis. Single point LIF measurement of atomic arsenic indicated that arsenic exist only in the low temperature, fuel rich region.