• Proceedings of the KIEE Conference
• /
• 1987.11a
• /
• pp.41-44
• /
• 1987

This paper is studied on the improvement of an efficiency and power factor for the single-phase induction motor with non-symmetrical cores. Since the motor construction having non-symmetrical core has the effect of reluctance torque and the rearrangement of revolving field, if core and winding design were optimized, the simple and economical permanent-capacitor-motor will be design. The most significant design variables are the degree of dissymmetry, the location of windings, and the turn-ratio between the main and auxiliary winding.

• Nuclear Engineering and Technology
• /
• v.53 no.4
• /
• pp.1109-1118
• /
• 2021

The construction of STELLA-2 facility is on-going to demonstrate the safety system of PGSFR and to provide comprehensive understanding of transient behavior under DBEs. Considering that most events are single-phase natural circulation flow with slow transient, STELLA-2 was designed with reduced-height of 1/5 length scale. The ratio of volume to surface area in the vessel can relatively increase resulting in excessive heat transfer. Therefore, a steady-state thermal-hydraulic analysis was performed and the effect of design change to reduce the heat transfer through redan was investigated. The heat transfer through single wall redan in STELLA-2 was 3% of the core power, comparable to 1% of the core power in PGSFR. By applying the insulated redan, about 70% of decrease effect was observed. The effect on transient behavior was also evaluated. The conclusion of this study was directly applied to the STELLA-2 design and the modified version is under construction.

• Current Optics and Photonics
• /
• v.6 no.2
• /
• pp.129-136
• /
• 2022

We propose a photonic crystal fiber (PCF) with a slotted porous core and elliptical-hole cladding, for high birefringence in the terahertz regime. Asymmetry in the guided mode is obtained mainly by using arrays of elliptical air holes in the TOPAS^® polymer cladding. We investigate the tradeoff between several structural parameters and find optimized values that can have a high birefringence while satisfying the single-mode condition. The optical properties in the terahertz regime are thoroughly analyzed in numerical simulations, using a full-vector finite-element method with the perfectly-matched-layer condition. In an optimal design, the proposed photonic crystal fiber shows a high birefringence of 8.80 × 10^-2 and an effective material loss of 0.07 cm^-1 at a frequency of 1 THz, satisfying the single-mode-guidance condition at the same time. The proposed PCF would be useful for various polarization-management applications in the terahertz range.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.3
• /
• pp.9-13
• /
• 2012

In order to overcome the complexity and power problems of superscalar processors, the multi-core architecture has been prevalent recently. Although the execution-driven simulation is wide spread, the trace-driven simulation has speed advantages over the execution-driven simulation. We present a methodology to simulate multi-core architecture using trace-driven simulator. Using SPEC 2000 benchmarks as input, the trace-driven simulation has been performed for the cores ranging from 2 to 16 extensively. As a result, the 16-core processor resulted in 4.1 IPC and 13.3 times speed up over single-core processor on the average.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.11
• /
• pp.54-63
• /
• 1997

The 1-D finite-element mehtod is applied for designing double-clad otpical fibers with dispersion-compensation capability. design parameters allowing only a $LP_{01}$ single mode are treated and macro-bending loss are taken into consideration. Design parameters are extracted to have the compensation ratio $(L_{SMF}/L_{DCF})$ of 6.2 for core structure with step-index profile, and of 5.2 for core with triangular-index profile.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2004.10a
• /
• pp.115-116
• /
• 2004

• Proceedings of the Korean Nuclear Society Conference
• /
• 2004.10a
• /
• pp.285-286
• /
• 2004

• Proceedings of the Korean Nuclear Society Conference
• /
• 2005.05a
• /
• pp.97-98
• /
• 2005

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 2004.11a
• /
• pp.323-328
• /
• 2004

• Progress in Superconductivity
• /
• v.5 no.2
• /
• pp.149-152
• /
• 2004

The design and the fabrication of a 1 MVA single-phase HTS transformer are presented in this paper, The rated voltages are 22.9 ㎸ for primary and 6.6 ㎸ for secondary, and the rated currents are 44 A and 152 A respectively. The transformer has HTS double pancake type windings. This type of winding has many advantages such as ease of fabrication and maintenance, good distribution of surge voltage and insulation of windings. Single HTS wire was used for primary winding and four HTS parallel wires were used for secondary winding. These windings are arranged reciprocally with the shell type iron core. An FRP cryostat with room temperature bore was fabricated to isolate the iron core from the coolant. The winding will be cooled down to 65 K with sub-cooled liquid nitrogen using a GM-cryocooler. The sub-cooled liquid nitrogen has advantages of good insulation because of no bubbles as well as increased current capacity of HTS wire.