• Journal of the Korean Geotechnical Society
• /
• v.23 no.8
• /
• pp.17-33
• /
• 2007

Downhole seismic method is widely used for obtaining shear wave velocity profile of a site because it is simple and economical. Determining accurate travel time of shear wave is very important to obtain reliable result in downhole seismic method. In this paper, comparison study of various travel time determination methods was performed. Numerical study and model chamber test were performed for effective comparison study. Signal traces were acquired by performing downhole test at each numerical simulation and soil box test. Travel time data for each signal traces were determined by using six different methods and Vs profiles were evaluated. Comparing travel time data and Vs profiles with the reference value, the first arrival picking method proved to be ambiguous and unreliable. Other methods also did not always provide accurate results and the magnitude of error was dependent on the signal to noise ratio. Cross-correlation method proved to be the most adequate method for the field application and it was verified additionally with field data.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.3
• /
• pp.59-68
• /
• 2010

Systematic risk management is necessary in grand scaled urban construction because of the existence of complicated and various risk factors. Problems of obstructions, adjacent structures, safety, environment, traffic and geotechnical properties need to be solved because urban construction is progressed in limited space not as general earthwork. Therefore the establishment of special risk management system is necessary to manage not only geotechnical properties but also social and cultural uncertainties. This research presents the technique analysis by the current state of risk management technique. Risk factors were noticed and the importance of each factor was estimated through survey. The systemically categorized database was established. Risk extraction module, matrix and score module were developed based on the database. Expected construction budget and time distribution can be computed by Monte Carlo analysis of probabilities and influences. Construction budgets and time distributions of before and after response can be compared and analyzed 80 the risks are manageable for entire whole construction time. This system will be the foundation of standardization and integration. Procurement, efficiency improvement, effective time and resource management are available through integrated management technique development and application. Conclusively decrease in cost and time is expected by systemization of project management.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.1
• /
• pp.51-63
• /
• 2022

Convoy driving is one of the technologies of multi-vehicle cooperation driving along with platoon driving. All over the world, research on vehicle control mechanisms to maintain vehicle formation during convoy driving convoy driving has been actively conducted and in Europe's Autonet 2030 project has developed and demonstrated convoy driving services for highways. But, even the concept of convoy driving is still insufficient in Korea. Therefore, in this study, the concept of convoy driving service was established and scenarios and communication messages for service application on urban roads were developed. And its effectiveness was verified through simulation analysis. As a result of comparing and analyzing individual vehicle cooperative driving and convoy driving for the blind spot support service and dilemma zone safety support service, which are representative V2I cooperative driving services on urban roads, the number of conflicts(indicator of traffic safety) and delays and stops(indicator of traffic efficiency) are significantly improved in convoy driving compared to individual vehicle cooperative driving.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.26 no.12
• /
• pp.1846-1854
• /
• 2022

The sophistication and diversification of mission equipment for surveillance and reconnaissance is leading to a demand for large-capacity public data links. Overseas, a T4 class(274Mbps) common data link was applied to the Global hwak, a high-altitude unmanned aerial vehicle, and various research and development are being conducted in Korea. In this paper, we propose a structure in which pilot is additionally applied to improve SNR performance while minimizing data transmission rate loss in the DVB-S2 frame structure, which is a european satellite broadcasting standard, for high-capacity transmission of T4 class or higher in the common data link. For the performance evaluation of the proposed structure, the performance of the DVB-S2 was compared and analyzed by simulating the UAV data link channel environment. As a result of simulation, 0.15% of transmission rate loss occurred at T4 class transmission rate compared to DVB-S2 in the proposed structure, but improved SNR reception performance of 0.2~0.3dB was confirmed in the UAV channel environment.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.111-111
• /
• 2021

메콩지역은 최근 연 7%에 육박하는 경제성장률을 달성하며 아세안의 고성장을 지속 견인하고 있으나, 기후변화 및 급속한 도시화로 매년 가뭄·홍수 등 물 관련 재해 발생 빈도 및 강도 증가와 이에 따른 상·하류 국가간 물 분쟁 등으로 인해 메콩지역 지속가능 발전에 지장이 초래되고 있다. 이에 한국과 미국은 메콩우호국(Friends of the Lower Mekong, FLM) "메콩지역 수자원 데이터 관리 및 정보공유 강화에 관한 공동성명(2018년 8월)"을 계기로 메콩유역의 실시간 수자원 변동 모니터링 및 분석과 수자원 데이터 공동활용 역량을 강화하여 효율적이고 과학적인 수자원관리 지원과 함께 한국의 신남방정책과 미국의 인도-태평양 전략 시너지효과를 극대화하고자 메콩 주변국 재해경감 및 수자원 데이터 활용 역량강화를 위한 글로벌 위성기반 수문자료의 생산·활용 및 홍수·가뭄 등의 수재해 분석기술을 개발하고 있다. 여기에는 한국 K-water의 물관리 기술과 미국 NASA, USACE의 위성활용 및 수자원분석 기술을 접목하여 메콩지역의 체계적인 물관리 및 재해로부터 안전성 확보 기여에 목표를 두고 연구를 진행 중에 있다. 본 연구에서는 전 세계적으로 광범위하게 활용되고 있는 미공병단(USACE, U.S. Army Corps of Engineers)의 HEC software 프로그램을 메콩 시범지역(pilot area)에 적용하여 수리/수문모델 구축을 진행코자 한다. 구축되는 모형은 유역 상류 댐의 연계 모의운영 및 하류 홍수분석이 동시 가능한 HEC-RTS(Real-Time Simulation)로 이는 HEC-HMS, -ResSim, -RAS와 -FIA 모형이 순차적으로 결합된 수리/수문 모델링 시스템이다. 모형의 시범적용 지역은 현지 메콩위원회(MRC, Mekong River Comission)의 의견 등을 반영, 메콩강 하류지역(Lower Mekong) 본류 유역에 위성 자료 활용 및 준실시간(near real-time)으로 댐 모의운영 등을 고려할 수 있는 JingHong댐(중국 란창강 최하류)에서 라오스 Xayaburi댐(메콩강 최상류)까지의 구간을 선정하였다. 한편, 금번 연구에서는 HEC-RTS 중 HMS 모형 적용을 중심으로 가용한 위성자료(GPM IMERG)와 K-LIS 지표 모형 생산 자료를 활용하여 과거 홍수사상에 대한 모의를 고려하였다. 아울러, 연구에서 구축된 HMS 모형은 HEC-RTS에 포함되어 메콩 시범지역의 종합적 수리/수문분석에 적용될 예정이다.

• Journal of Korea Water Resources Association
• /
• v.56 no.1
• /
• pp.23-34
• /
• 2023

This study analyzed the bed load transport and channel change on the vegetation zone through laboratory experiments and numerical simulations. To examine the effect of vegetation zone in the laboratory experiment, artificial vegetation zones made of acrylic sticks were installed in the experimental channel, and discharge conditions were adjusted to examine the bed load transport and channel change in the vegetation zone. Next, numerical simulations were performed by applying the same conditions as those of the laboratory experiment to the Nays2D model, a two-dimensional numerical model, and the applicability of the numerical model was examined by comparing the results with the results of the laboratory experiment. Finally, by applying a numerical model, the bed load transport and channel change according to the change in vegetation density were examined. As a result of examining the bed load transport and channel change in the vegetation zone according to the discharge condition change by applying the laboratory experiment and the numerical model, the results of the two application methods were similar. As the discharge increased, bed load from the upper stream was deposited inside the vegetation zone. On the other hand, on the other side of the vegetation zone, the flow was concentrated and erosion occurred. Also, the range of erosion increased in the downstream direction. As a result of examining the bed load transport and channel change according to the change in vegetation density, as the vegetation density increased, the bed load from the upper stream was deposited inside the vegetation zone. On the other hand, due to the increase in vegetation density, the flow was concentrated to the opposite side of the vegetation zone, erosion occurred.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.2C
• /
• pp.133-142
• /
• 2006

Many methods have been tried to more correctly measure rock joint roughness. However, true roughness may be distorted and underestimated due to the sampling interval and measurement method. Thus, currently used measurement methods produce a dead zone and distort roughness profiles. The purpose of this study is to suggest new roughness measurement method by a camera-type 3D scanner as an alternative of currently used methods. First, the underestimation of artificial roughness is analyzed by using the current measurement method such as laser profilometry. Second, we replicate eight specimens from two rock joint surfaces, and digitize by a 3D scanner. Then, the roughness coefficient values obtained from eight numbers of 3D surface data and from three hundred twenty numbers of 2D profiles data are analyzed by using current and new measurement methods. The artificial simulation confirms that the sampling interval is one of main factors for the distortion of roughness and shows that inclination of waviness may not be considered any current methods. The experimental results show that the camera-type 3D scanner produces 10% larger roughness values than current methods. As the proposed new method is a fast, high precision and more accurate method for the roughness measurement, it should be a promising technique in this area.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.1D
• /
• pp.95-103
• /
• 2006

One of the main functions of the 4D system includes visualizing numerical schedule data in construction. The existing 4D tools have an excellent function for simulating building projects that all activities are progressed according to vertical work zone. However, it is not easy to implement all of it in the civil engineering project because the construction activities of highway and railway projects are progressed on the horizontal work zone and the 4D simulation for those projects should include earthwork objects that depend on the natural ground condition. This study suggests a new methodology for improving those limitations of 4D system for the civil engineering project and develops a new system by the suggested methodology. To verify the developed system, this study attempts to simulate 4D object for horizontal elements such as earthwork, paving work and tunneling work. The morphing and multi-texturing techniques developed in the study can be new approaches to simulate 4D object for the earthwork such as cutting and banking whose activities are progressed on the natural ground condition. The research results can be expected as a draft function for improving the application of 4D system in civil engineering projects.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.121-121
• /
• 2022

한국과 미국은 2018년 8월에 발표한 메콩우호국(Friends of the Lower Mekong, FLM) "메콩지역 수자원 데이터 관리 및 정보공유 강화에 관한 공동성명"을 계기로 메콩유역의 실시간 수자원 변동 모니터링 및 분석과 수자원 데이터 공동활용 역량을 강화하여 효율적이고 과학적인 수자원관리 지원과 함께 한국의 신남방정책과 미국의 인도-태평양 전략 시너지효과를 극대화하고자 메콩 주변국 재해경감 및 수자원 데이터 활용 역량강화를 위한 글로벌 위성기반 수문자료의 생산·활용 및 홍수·가뭄 등의 수재해 분석기술을 개발하고 있다. 여기에는 한국 K-water의 물관리 기술과 미국 NASA, USACE의 위성활용 및 수자원분석 기술을 접목하여 메콩지역의 체계적인 물관리 및 재해로부터 안전성 확보 기여에 목표를 두고 연구를 진행 중에 있다. 본 연구에서는 전 세계적으로 광범위하게 활용되고 있는 미공병단(USACE, U.S. Army Corps of Engineers)의 HEC software 프로그램을 메콩 시범지역(pilot area)에 적용하여 수리/수문모델 구축을 진행하고 있다. 구축되는 모형은 유역 상류 댐의 연계 모의운영 및 하류 홍수분석이 동시 가능한 HEC-RTS(Real-Time Simulation)로 이는 HEC-HMS, -ResSim, -RAS와 -FIA 모형이 순차적으로 결합된 수리/수문 모델링 시스템이다. 모형의 시범적용 지역은 현지 메콩위원회(MRC, Mekong River Comission)의 의견 등을 반영, 메콩강 하류지역(Lower Mekong) 본류 유역에 위성자료 활용 및 준실시간(near real-time)으로 댐 모의운영 등을 고려할 수 있는 JingHong댐(중국 란창강 최하류)에서 라오스 Xayaburi댐(메콩강 최상류)까지의 구간을 선정하였으며, 전년도에는HEC-RTS 중 HMS(Hydrologic Modeling System) 모형 적용을 중심으로 가용한 위성자료(GPM IMERG)를 활용하여 과거 홍수사상에 대한 모의를 고려한 강우-유출모형의 구축을 완료하였다. 이에 연속하여 금년도에는 동일유역 내 하천 단면 등이 확보된 Chiang Saen 지점에서 Xayaburi 댐까지의 구간에 대해 RAS(River Analysis System)을 구축할 예정으로 구축된 RAS 모형은 HEC-RTS에 포함되어 메콩 시범지역의 종합적 수리/수문분석에 적용될 예정이다.

• Steel and Composite Structures
• /
• v.49 no.5
• /
• pp.517-532
• /
• 2023

Tower structures have been widely used in communication and transmission engineering. The failure of joints is the leading cause of structure failure, which make it play a crucial role in tower structure engineering. In this study, the aluminum alloy three tube tower structure is taken as the prototype, and the middle joint of the tower was selected as the research object. Three different stainless steel-aluminum alloy composite joints (SACJs), denoted by TA, TB and TC, were designed. Finite element (FE) modeling analysis was used to compare and determine the TC joint as the best solution. Detail requirements of fasteners in the TC stainless steel-aluminum alloy composite joint (TC-SACJ) were designed and verified. In order to systematically and comprehensively study the mechanical properties of TC-SACJ under multi-directional loading conditions, the full-scale experiments and FE simulation models were all performed for mechanical response analysis. The failure modes, load-carrying capacities, and axial load versus displacement/stain testing curves of all full-scale specimens under tension/compression loading conditions were obtained. The results show that the maximum vertical displacement of aluminum alloy tube is 26.9mm, and the maximum lateral displacement of TC-SACJs is 1.0 mm. In general, the TC-SACJs are in an elastic state under the design load, which meet the design requirements and has a good safety reserve. This work can provide references for the design and engineering application of aluminum alloy tower structures.