• The Journal of Advanced Prosthodontics
• /
• v.9 no.2
• /
• pp.130-137
• /
• 2017

PURPOSE. The purpose of this study was to evaluate the effect of nano-structured alumina surface coating on shear bond strength between Y-TZP ceramic and various dual-cured resin cements. MATERIALS AND METHODS. A total of 90 disk-shaped zirconia specimens (HASS CO., Gangneung, Korea) were divided into three groups by surface treatment method: (1) airborne particle abrasion, (2) tribochemicalsilica coating, and (3) nano-structured alumina coating. Each group was categorized into three subgroups of ten specimens and bonded with three different types of dual-cured resin cements. After thermocycling, shear bond strength was measured and failure modes were observed through FE-SEM. Two-way ANOVA and the Tukey's HSD test were performed to determine the effects of surface treatment method and type of cement on bond strength (P<.05). To confirm the correlation of surface treatment and failure mode, the Chi-square test was used. RESULTS. Groups treated with the nano-structured alumina coating showed significantly higher shear bond strength compared to other groups treated with airborne particle abrasion or tribochemical silica coating. Clearfil SA Luting showed a significantly higher shear bond strength compared to RelyX ARC and RelyX Unicem. The cohesive failure mode was observed to be dominant in the groups treated with nano-structured alumina coating, while the adhesive failure mode was prevalent in the groups treated with either airborne particle abrasion or tribochemical silica coating. CONCLUSION. Nano-structured alumina coating is an effective zirconia surface treatment method for enhancing the bond strength between Y-TZP ceramic and various dual-cured resin cements.

• Advances in concrete construction
• /
• v.11 no.2
• /
• pp.127-140
• /
• 2021

In this study, twenty-five geopolymer (GP) mixes were prepared by varying the alkaline solids to Metakaolin (MK) and sodium silicate to NaOH ratios from 0.1 to 0.5 and 0.2 to 1.0, respectively, thus giving a wide range of molar ratios of silica to alumina, sodium oxide to alumina and water to sodium oxide. The compressive strength of these GP mixes was determined for four curing schemes involving oven curing at 100℃ for 24 h and three ambient curing with the curing ages of 3, 14, and 28 days. The test results revealed that for the manufacture of GP binder for structural applications of strength up to 90 MPa, the molar ratio of silica to alumina should be greater than 2.3, sodium oxide to alumina should be between 0.6 to 1.2, and water to sodium oxide should not exceed 12. The compressive strength of ambient cured GP mortar gets stabilized at 28 days of ambient curing. Experimental findings were also corroborated by GP microstructure analysis. The embodied energy of MK-based GP mortars, especially of high strength, is significantly less than the cement mortar of equivalent strength.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.8
• /
• pp.134-140
• /
• 2002

Chemical mechanical polishing of aluminum and photoresist using colloidal silica-based slurry was experimented. The effects of slurry pH, silica concentration, and oxidizer ($H_2O_2$) concentration on surface roughness and removal rate were studied. The optimum slurry conditions for reduction of micro-scratch were investigated. The optimum chemical mechanical polishing with the colloidal silica-based slurry was compared with conventional chemical mechanical polishing with alumina-based slurry. Chemical mechanical polishing of the aluminum with the colloidal silica-based slurry showed improved result but chemical mechanical polishing of the photoresist did not. The improved result was comparative with that of chemical mechanical polishing with filtered alumina-based slurry which one of desirable methods to reduce the micro-scratch.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1992.05b
• /
• pp.125-125
• /
• 1992

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1997.10a
• /
• pp.169-169
• /
• 1997

• Bulletin of the Korean Chemical Society
• /
• v.11 no.6
• /
• pp.568-570
• /
• 1990

• The Journal of Advanced Prosthodontics
• /
• v.10 no.1
• /
• pp.43-49
• /
• 2018

PURPOSE. The purpose of this in vitro study is to examine the effects of a nano-structured alumina coating on the adhesion between resin cements and zirconia ceramics using a four-point bending test. MATERIALS AND METHODS. 100 pairs of zirconium bar specimens were prepared with dimensions of $25mm{\times}2mm{\times}5mm$ and cementation surfaces of $5mm{\times}2mm$. The samples were divided into 5 groups of 20 pairs each. The groups are as follows: Group I (C) - Control with no surface modification, Group II (APA) - airborne-particle-abrasion with $110{\mu}m$ high-purity aluminum oxide ($Al_2O_3$) particles, Group III (ROC) - airborne-particle-abrasion with $110{\mu}m$ silica modified aluminum oxide ($Al_2O_3+SiO_2$) particles, Group IV (TCS) - tribochemical silica coated with $Al_2O_3$ particles, and Group V (AlC) - nano alumina coating. The surface modifications were assessed on two samples selected from each group by atomic force microscopy and scanning electron microscopy. The samples were cemented with two different self-adhesive resin cements. The bending bond strength was evaluated by mechanical testing. RESULTS. According to the ANOVA results, surface treatments, different cement types, and their interactions were statistically significant (P<.05). The highest flexural bond strengths were obtained in nano-structured alumina coated zirconia surfaces (50.4 MPa) and the lowest values were obtained in the control group (12.00 MPa), both of which were cemented using a self-adhesive resin cement. CONCLUSION. The surface modifications tested in the current study affected the surface roughness and flexural bond strength of zirconia. The nano alumina coating method significantly increased the flexural bond strength of zirconia ceramics.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.3 no.3
• /
• pp.199-205
• /
• 2015

The mechanical and thermal properties of high temperature aluminate cementitious thermal storage materials were investigated in this paper. Alumina cement was used as basic binder and the effect of the replacement of fly ash, silica fume, calcium sulfo-aluminate and graphite for alumina cement was investigated. Experiments were performed to measure mechanical properties including compressive strength before and after thermal cycling, and split tensile strength, and to measure thermal properties including thermal conductivity and specific heat. Test results show that the residual compressive strengths of mixtures with alumina cement only, or alumina cement and silica fume were greater than those of the others. Additionally, the specific heat of mixture with graphite was largest in all the mixtures used in the study. The results of this study could be used to provide realistic information for material properties in thermal energy storage concrete in the future.

• Journal of the Korean institute of surface engineering
• /
• v.33 no.5
• /
• pp.381-386
• /
• 2000

It was found that colloidal silica sprayed to the galvanized steel sheet apparently made the molten zinc layer solidified to be the randomly oriented fine grains. Its spraying effect was also little affected by steel temperature that had been considered as one of the major operating factors in this process. From the results of surface analysis, it is considered that aluminum dissolved in coating layer reduces silica to silicon by the oxidation-reduction reaction, and that the reduced silicon acts as a more effective nucleus in solidification reaction than phosphate salt, siica and alumina.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.3
• /
• pp.421-427
• /
• 2016

Nanosized hollow silica was prepared by $St{\ddot{o}}ber$ method in the presence of aluminum isopropoxide. The mixture of polyelectrolytes such as poly(sodium 4-styrene sulfonate)(PSS) and polyacrylic acid(PAA) were used as templates. Tetraethylorthosilicate(TEOS) and aluminum isopropoxide were used as precursors for silica and alumina, respectively. The function of aluminum isopropoxide is to increase the porosity of silica shell. The characterizations of hollow silica were examined by TEM(transmission electron microscopy), TGA(thermogravimetric analysis), BET(Brunauer Emmett Teller), Energy-dispersive X-ray spectroscopy(EDS), and FT-IR spectrum. It was found that the shell thickness of hollow silica was around 8 nm and the core diameter was around 20 nm by TEM.