• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.49 no.4
• /
• pp.492-499
• /
• 2013

The characteristics of abrasive wear of the rubber matrix composites filled with nano sized silica particles were investigated at ambient temperature by pin-on-disc friction test. The range of volume fraction of silica particles tested are between 11% to 25%. The cumulative wear volume and friction coefficient of these materials on particle volume fraction were determined experimentally. The major failure mechanisms were lapping layers, deformation of matrix, ploughing, deboding of particles and microcracking by scanning electric microscopy photograph of the tested surface. The cumulative wear volume showed a tendency to increase nonlinear with increase of sliding distance. As increasing the silica particles of these composites indicated higher friction coefficient.

• Bulletin of the Korean Chemical Society
• /
• v.29 no.11
• /
• pp.2281-2283
• /
• 2008

• Journal of Magnetics
• /
• v.20 no.3
• /
• pp.221-228
• /
• 2015

Colloidal particles consisted of individual nanosized magnetite grains on the surface of the silica cores were obtained by two-stage sol-gel technique. Size distribution and microstructure of the particles were analyzed using atomic force microscopy, X-ray diffraction and Nitrogen thermal desorption. Magnetic properties of the particles were studied by the method of the longitudinal nonlinear response. It has been shown that nanoparticles of magnetite have a size corresponding to a superparamagnetic state but exhibit hysteresis properties. The phenomenon was explained using the magnetostatic interaction model based on the hypothesis of iron oxide particles cluster aggregation on the silica surface.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.29 no.1
• /
• pp.69-79
• /
• 2013

The aim of this study was to evaluate the effect of surface conditioning on the shear bond strength of zirconium-oxide ceramic to resin cement. A total of 120 disk-shaped zirconium-oxide ceramic blocks(3-TZP, Kyoritsu, Tokyo, Japan) were treated as follows: (1) no treatment; (2) sandblasting with 110 ${\mu}m$ aluminum-oxide(Al2O3); (3) particles tribochemical silica coating(RocatecTM, 3M ESPE). Then zirconium-oxide ceramic blocks were divided into six groups(10 for each group) and bonded with resin cement(Rely X U-200, 3M ESPE). (1) No treatment / No treatment (2) No treatment / Sandblasting with 110 ${\mu}m$ aluminum-oxide particles (3) No treatment / Silica coating (4) Sandblasting with 110 ${\mu}m$ aluminum-oxide particles / Sandblasting with 110 ${\mu}m$ aluminum-oxide particles (5) Sandblasting with 110 ${\mu}m$ aluminum-oxide particles / Silica coating (6) Silica coating / Silica coating. Each group was tested in shear bond strengths by UTM. Data analysis included one-way analysis of variance(ANOVA) and the Tukey Honestly Significant Difference test (P=0.05). Group that bonded two silica coated specimen showed a highest bond strength(P<0.05). Two silica coated surface conditioning group and air-abrasion and silica coated surface conditioning group showed significantly difference with other groups(P<0.05). Other groups had no significantly difference each other. Within the limitation of this study, Surface conditioning with Rocatec treatment to each side of specimen provided the highest bond strength.

• Applied Chemistry for Engineering
• /
• v.18 no.2
• /
• pp.183-187
• /
• 2007

$SiO_2/TiO_2$ core-shell particles with controlled shell thickness were prepared using large silica particles. The thickness of titania coating layer was varied from 8 nm to 38 nm depending on the number of coating steps from 1 to 3 times. After titania coating, the core-shell particles showed textured surface due to the titania coating layer, resulting in 3~25 times increase of specific surface areas. The properties of titania coated silica particles were characterized by FE-SEM, Zeta potential meter, BET, and XRD.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1158-1161
• /
• 2006

The toner type paper-like display (PLD) has been developed with two polymer particles having opposite polarity which is composed of polymer, colorant and external additives (nano-sized silica). Nano-sized silica with triboelectric charge was used for the charge control agent (CCA) and influenced on the electrostatic properties of the silica-coated polymer particles. The PLD cell using silica-coated particles (200 seconds) had shown a good white appearance and low driving voltage. The result could be explained in terms of the surface morphology and the cohesiveness depending on the silica coating time.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.10
• /
• pp.2943-2948
• /
• 2010

Silica monolith powders were prepared by a new procedure where ground powders of proper size distribution were obtained without sieving. An initiator was attached to this ground monolith and polystyrene was bound by reversible addition-fragmentation chain transfer polymerization to give a new stationary phase. The separation efficiency of this phase was found better than that of the polystyrene bound phase based on conventional silica particles and that of the C18 bound silica monolith powders.

• Membrane Journal
• /
• v.20 no.2
• /
• pp.87-96
• /
• 2010

We prepared spherical silica particles by controlling various conditions of emulsion-gel procedure using a lab-scale membrane emulsification system equipped with SPG (Shirasu porous glass) membrane having pore size of 2.6 ${\mu}m$. We determined the effects of process parameters of membrane emulsification (dispersed phase pressure, stabilizer and emulsifier concentration in continuous phase, $H_2O$/TEOS ratio, ratio of dispersed phase to continuous phase) on the mean size and size distribution of silica particles. The increase of the dispersed phase pressure and ratio of dispersed phase to continuous phase led to the increase in the mean size of silica particles. On the contrary, the increase in stabilizer and emulsifier concentration and $H_2O$/TEOS ratio caused the reduction of the mean size of particles. Through controlling these parameters, monodisperse spherical silica particles with about 3 ${\mu}m$ of the mean size were finally prepared.

• Polymer(Korea)
• /
• v.30 no.1
• /
• pp.75-79
• /
• 2006

Silica nanoparticles for polymeric dental restorative composites were prepared by Stober method, and then the effects of surface treatment of silica particles with Lmethacrylofpropyltrimethofsilane $(\gamma-MPS)$ on the dispersity of the silica particles in the organic matrix was investigated. Particles having various average size were prepared by using controlled amounts of tetraethylorthosilicate(TEOS), water, and catalyst and by changing solvent used for reaction. The site of particles prepared by using methanol as solvent was smaller than that prepared by using ethanol as solvent. In addition, the size of particles was increased by decreasing amounts of water and by increasing amounts of TEOS and catalyst. Hydrophobic silica nanoparticles was prepared by reacting hydrophilic nanoparticles with $\gamma-MPS$ to improve interfacial properties with organic matrix. Amounts of $\gamma-MPS$ per unit mass of the particles was increased by decreasing particle size. even though the amount of $\gamma-MPS$ per specific surface area were nearly the same regardless of the particle size. The dispersity of the silica particles in the organic matrix was improved when the surface treated silica particles were used for preparing the polymeric dental restorative composites.

• Korean Chemical Engineering Research
• /
• v.54 no.6
• /
• pp.792-799
• /
• 2016

Monodisperse silica nanospheres were synthesized by Stober method using rotating cylinder systems with batch or continuous manner. The particle size could be controlled by adjusting the reactant compositions such as the amount of monomer, catalyst, and water in the reaction mixture. The size and monodispersity of the ceramic particles could be controlled by changing the reaction medium with different alcohols other than ethanol or changing the reaction temperature. The effect of Taylor number (Ta) on the average diameter and standard deviation of silica particles were also studied by adjusting the rotation speed of inner cylinder, and the maximum diameter of particles was observed at Ta ${\approx}3,000$.