• 한국농공학회지
• /
• 제26권1호
• /
• pp.52-72
• /
• 1984

This study was performed to obtain the basic data which can be applied to the use of epoxy resin mortars. The data was based on the properties of epoxy resin mortars depending upon various mixing ratios to compare those of cement mortar. The resin which was used at this experiment was Epi-Bis type epoxy resin which is extensively being used as concrete structures. In the case of epoxy resin mortar, mixing ratios of resin to fine aggregate were 1: 2, 1: 4, 1: 6, 1: 8, 1:10, 1 :12 and 1:14, but the ratio of cement to fine aggregate in cement mortar was 1 : 2.5. The results obtained are summarized as follows; 1.When the mixing ratio was 1: 6, the highest density was 2.01 g/cm$^3$, being lower than 2.13 g/cm$^3$ of that of cement mortar. 2.According to the water absorption and water permeability test, the watertightness was shown very high at the mixing ratios of 1: 2, 1: 4 and 1: 6. But then the mixing ratio was less than 1 : 6, the watertightness considerably decreased. By this result, it was regarded that optimum mixing ratio of epoxy resin mortar for watertight structures should be richer mixing ratio than 1: 6. 3.The hardening shrinkage was large as the mixing ratio became leaner, but the values were remarkably small as compared with cement mortar. And the influence of dryness and moisture was exerted little at richer mixing ratio than 1: 6, but its effect was obvious at the lean mixing ratio, 1: 8, 1:10,1:12 and 1:14. It was confirmed that the optimum mixing ratio for concrete structures which would be influenced by the repeated dryness and moisture should be rich mixing ratio higher than 1: 6. 4.The compressive, bending and splitting tensile strenghs were observed very high, even the value at the mixing ratio of 1:14 was higher than that of cement mortar. It showed that epoxy resin mortar especially was to have high strength in bending and splitting tensile strength. Also, the initial strength within 24 hours gave rise to high value. Thus it was clear that epoxy resin was rapid hardening material. The multiple regression equations of strength were computed depending on a function of mixing ratios and curing times. 5.The elastic moduli derived from the compressive stress-strain curve were slightly smaller than the value of cement mortar, and the toughness of epoxy resin mortar was larger than that of cement mortar. 6.The impact resistance was strong compared with cement mortar at all mixing ratios. Especially, bending impact strength by the square pillar specimens was higher than the impact resistance of flat specimens or cylinderic specimens. 7.The Brinell hardness was relatively larger than that of cement mortar, but it gradually decreased with the decline of mixing ratio, and Brinell hardness at mixing ratio of 1 :14 was much the same as cement mortar. 8.The abrasion rate of epoxy resin mortar at all mixing ratio, when Losangeles abation testing machine revolved 500 times, was very low. Even mixing ratio of 1 :14 was no more than 31.41%, which was less than critical abrasion rate 40% of coarse aggregate for cement concrete. Consequently, the abrasion rate of epoxy resin mortar was superior to cement mortar, and the relation between abrasion rate and Brinell hardness was highly significant as exponential curve. 9.The highest bond strength of epoxy resin mortar was 12.9 kg/cm$^2$ at the mixing ratio of 1:2. The failure of bonded flat steel specimens occurred on the part of epoxy resin mortar at the mixing ratio of 1: 2 and 1: 4, and that of bonded cement concrete specimens was fond on the part of combained concrete at the mixing ratio of 1 : 2 ,1: 4 and 1: 6. It was confirmed that the optimum mixing ratio for bonding of steel plate, and of cement concrete should be rich mixing ratio above 1 : 4 and 1 : 6 respectively. 10.The variations of color tone by heating began to take place at about 60˚C, and the ultimate change occurred at 120˚C. The compressive, bending and splitting tensile strengths increased with rising temperature up to 80˚ C, but these rapidly decreased when temperature was above 800 C. Accordingly, it was evident that the resistance temperature of epoxy resin mortar was about 80˚C which was generally considered lower than that of the other concrete materials. But it is likely that there is no problem in epoxy resin mortar when used for unnecessary materials of high temperature resistance. The multiple regression equations of strength were computed depending on a function of mixing ratios and heating temperatures. 11.The susceptibility to chemical attack of cement mortar was easily affected by inorganic and organic acid. and that of epoxy resin mortar with mixing ratio of 1: 4 was of great resistance. On the other hand, when mixing ratio was lower than 1 : 8 epoxy resin mortar had very poor resistance, especially being poor resistant to organicacid. Therefore, for the structures requiring chemical resistance optimum mixing of epoxy resin mortar should be rich mixing ratio higher than 1: 4.

• Clinical and Experimental Reproductive Medicine
• /
• 제37권1호
• /
• pp.57-64
• /
• 2010

목 적: 배양 환경과 동결 기술이 발달함에 따라 동결 포배의 해동-이식의 빈도가 증가하고 있으며, 신선 주기와 마찬가지로 해동-이식 주기에서도 질 좋은 배아를 선별하는 것은 임신 성공 여부를 결정하는 아주 중요한 과제이다. 본 연구는 동결 당시 포배로의 발달 속도가 임신 결과에 미치는 영향을 알아보기 위하여, 수정 후 5일 및 6일째 동결한 포배의 해동-이식 후 임신율을 비교 분석하였다. 연구방법: 2006년 1월부터 12월까지 5일째 또는 6일째 동결한 포배를 해동하여 2007년 6월까지 융해 이식한 87명, 93주기를 대상으로 하였다. 동결법은 ethylene glycol과 DMSO를 이용한 유리화 동결법을 이용하였으며, 팽창 포배는 인위적인 수축을 시행 후 동결하였다. 해동 과정은 이식 전날 시행하여 15~18시간 배양액에서 배양 후 재팽창 여부를 확인하였다. 결 과: 5일째 동결한 포배를 해동-이식한 52주기와 6일째 동결한 포배를 해동-이식한 41주기에서 환자의 나이, 이식한 배아의 수, 해동 배아의 생존율 등 임신 결과에 영향을 미칠만한 요인들의 차이는 없었다. 그러나 생화학적 임신율, 임상적 임신율, 진행 임신율, 착상율 등은 5일째 동결한 포배를 해동-이식한 주기에서 높게 나타났다. 결 론: 5일째 동결한 포배를 해동-이식했을 때의 임신율은 6일째 동결한 포배를 해동-이식했을 때의 임신율보다 2배 이상 높았으며, 이는 신선 주기와 마찬가지로 해동-이식 주기에서도 동결 전 배아의 발달 속도의 차이를 임신 성공 예측의 중요한 지표로 사용할 수 있음을 시사한다.

• 헤리티지:역사와 과학
• /
• 제50권4호
• /
• pp.148-165
• /
• 2017

고분 내부에 그려진 벽화는 온 습도 등 환경변화에 매우 민감하며, 특히 고분벽화의 마감층은 사용된 재료 특성과 습도 조건에 따라 보존성에 각기 다른 양상을 나타낸다. 본 연구에서는 토양을 사용하여 마감층을 제작한 송산리 6호분 벽화를 대상으로, 마감층의 재료 특성에 따라 건조로 인해 발생될 수 있는 물리적 변화 양상을 파악하였다. 입도분석 결과 송산리 6호분 벽화 마감층은 실트 이하가 약 85.0wt%, 그 안의 점토가 약 14.0wt%로 대부분이 실트와 점토이하로 이루어진 것으로 나타났다. 의사시료에 대한 물성평가 결과 표면 변화율은 벤토나이트 마감층 재현 시료가 15.5%로 가장 큰 변화를 나타냈으며, 그 다음으로 청자토 마감층 재현 시료 7.8%, 황토 마감층 재현 시료 6.3% 그리고 백토 마감층 재현 시료 6.2%의 순으로 확인되었고, 태토별 시료에서도 같은 순서의 변화 양상을 보였다. 또한 수축률 및 팽창률 측정 결과에서도 유사한 경향의 표면 변화율을 나타냈으며, 벤토나이트 조건이 가장 큰 변화를 보였다. 실험결과, 토양으로 구성된 마감층은 미분부 함량으로 인한 입자간의 응집도와 함께 점토광물의 종류에 따른 팽창성 등의 영향으로 인한 응력과의 관계 등이 물리적 변화에 영향을 미치는 것으로 판단된다. 따라서 송산리 6호분 벽화 마감층에 발생된 물리적 손상은 토양이 갖는 재료적 특성과 고습한 고분 내부에서 발생되는 환경변화 등의 요인과 연관성이 있을 것으로 판단된다.

• Journal of the Korean Wood Science and Technology
• /
• 제6권2호
• /
• pp.3-19
• /
• 1978

우리나라에서 아직 이용개발(利用開發)되고 있지 아니한 구상나무, 구실잣밤나무, 후박나무, 때죽나무 및 북가시나무등(等) 5수종(樹種)에 대(對)한 해부학적성질(解剖學的性質), 물리적성질(物理的性質), 기계적성질(機械的性質), 접착성능(接着性能), 목리(木理) 무늬정미성(精緻性), 가공성(加工性), 건조특성(乾燥特性), 프로링제작성(製作性), 목재(木材)의 조성분(組成分), 펄프화특성(化特性) 및 박피성등(剝皮性等)을 조사(調査)한 결과(結果)를 요약(要約)하면 다음과 같다. 1. 원료목재(原料木材)의 형질(形質)은 구상나무가 통직(通直)하나 옹이가 과다(過多)하였고, 잣밤나무와 때쭉나무는 굽음이 심(甚)하였다. 2. 섬유장(纖維長)은 구상나무가 2.97mm로 가장 컷으며, 때죽나무가 1.49mm였으며, 기타(其他) 수종(樹種)도 1.07~1.19mm에 속하였다. 섬유폭(纖維幅)은 구상나무가 39.3${\mu}$으로 가장 컸고, 때죽나무가 18.4${\mu}$으로 최소(最小)였으며 기타(其他) 수종(樹種)들은 23~29${\mu}$의 범위(範圍)에 속하나 대체(大體)로 타활엽수(他闊葉樹)에 비(比)해 섬유폭(纖維幅)이 컸다. 3. 북가시나무의 전건비중(全乾比重)은 0.74${\pm}$0.03으로서 한국산(韓國産) 참나무류(類)의 비중(比重)과 유사(類似)하였으며 구상나무는 0.34${\pm}$0.02로 최소(最小)였으며 기타(其他) 수종(樹種)은 0.47~0.51의 범위(範圍)에 있었다. 4. 흡수량(吸水量)은 대체(大體)로 비중(比重)에 역비례(逆比例)하여 감소(減少)되나 흡습량(吸濕量)은 비중(比重) 증가(增加)에 따라서 증가(增加)하는 경향(傾向)을 나타냈다. 또한 횡단면(橫斷面)의 흡수량(吸水量)은 경단면(經斷面) 접선단면(接線斷面)의 그것들에 비(比)해 2배(倍) 이상(以上)에 달(達)하나, 후박나무는 1.7배(倍)였으며, 경단면(經斷面)과 접선단면(接線斷面)의 흡수량(吸水量)은 수종(樹種)에 따라서 달랐다. 5. 전건수축율(全乾收縮率)은 접선방향(接線方向)에서 5.36~10.24%, 반경방향(半徑方向)에서 2.83~6.13%에 범위(範圍)에 속하며 구상나무가 가장 적고, 북가시나무가 가장 컸다. 수축율(收縮率)은 비중(比重)이 큰 수종(樹種)일수록 컸다. 6. 공시수종(供試樹種)의 제강도(諸强度)는 북가시나무의 경우 강원도산(江原道産) 신갈나무와 유사(類似)하였으며, 구실잣밤나무, 후박나무 구상나무는 비중(比重)이 유사(類似)한 한국산수종(韓國産樹種)의 재질(材質)들과 유사(類似)하였으나, 때쭉나무는 일반적(一般的)으로 비중(比重)에 비(比)해 높은 강도치(强度値)를 기록(記錄)하였다. 7. 요소수지(尿素樹脂) 및 석탄산수지(石炭酸樹脂)에 대(對)한 접착(接着)은 후박나무와 구실잣밤나무가 최대치(最大値)를 기록(記錄)하였으나, 비중(比重)이 큰 북가시나무와 비중(比重)이 작은 구상나무는 그렇지 못하였다. 8. 목리(木理)와 무늬정치성(精緻性)은 후박나무는 파상(波狀)으로 굴곡(屈曲)되어 목재공예적(木材工藝的)으로 진용(珍用)될 수 있으며 기타(其他) 수종(樹種)들은 건축(建築) 및 가구용재(家具用材)로서 적합(適合)한 무늬였다. 6. 가공성(加工性)은 북가시나무를 제외(除外)하곤 기타 수종(樹種)은 양호(良好)할 것으로 판단(判斷)된다. 10. 비중(比重)이 큰 수종(樹種)일수록 건조(乾燥)의 곤란성(困難性)을 노정(露呈)하였으나, 후박나무는 비중(比重)에 비(比)해 건조(乾燥)가 용이(容易)치 않고, 심(甚)한 트위스팅 및 커핑 등(等) 건조결함(乾燥缺陷)을 발생(發生)하였다. 11. 구상나무를 제외(除外)한 모든 공시수종(供試樹種)은 플로링제작(製作)에 적합(適合)한 것으로 판단(判斷)된다. 12. 화학적(化學的) 조성분(組成分)은 5수종(樹種) 공(共)히 펜토산 함량(含量)이 많았고 북가시나무는 추출물(抽出物)의 함량(含量)이 최대(最大)였다. 13. 크라프트 펄프화(化)는 5수종(樹種) 공(共)히 경제수율(經濟收率)인 45% 이상(以上)을 기록(記錄)하였다. 14. 박피(剝皮)는 구상나무와 후박나무가 용이(容易)하였으며, 5수종(樹種) 모두 자비(煮沸)한 후(後) 박피(剝皮)한 것이 가장 능율적(能率的)이었다.

• Journal of Korean Neurosurgical Society
• /
• 제30권11호
• /
• pp.1263-1270
• /
• 2001

Objective : To analyze the radiosurgical results of intracranial meningiomas after Gamma Knife radiosurgery (GKS) and to assess the possible factors related to the outcome and complications in treating meningiomas. Patients and Methods : We retrospectively reviewed the clinical and radiological data in 179 patients(194 lesions) treated with GKS for intracranial meningiomas between May 1992 and October 2000. Radiosurgical responses were categorized as shrinkage, stasis and enlargement, and we defined the shrunken and static group as a radio-logical control. A Cox proportional hazards model was used to evaluate the correlation between the radiosurgical outcomes and various factors such as location and size of tumor, age and gender of patients, relation to venous sinus, pre-GKS degree of edema, treatment modality, radiosurgical parameters, and pathologic findings. Results : Patients were grouped into skull base meningiomas(57.7%), non-skull base tumor including convexity, parasagittal, and falx meningiomas(37.1%), and others(5.2%) according to the location of tumors. The mean maximum dose and the margin dose of tumor was 30.0Gy(19-45Gy) and 15.1Gy(9.5-24.5Gy), respectively. The mean volume of the tumors was 9.4cc(0.003-45.0cc). The radiologic control rate was 97.1%. The radiation induced imaging change with or without neurologic deficit was the most common complication(23.6%). There were seen mostly in convexity, parasagittal, and falx meningiomas which were deeply embedded in cortex. Conclusion : GKS for intracranial meningioma seems to be safe and effective treatments. However, GKS should be considered very cautiously in non-skull base tumor such as convexity, parasagittal, or falx meningiomas with regards to patient's age and general condition, size and location of tumor, pattern of embedding into cortex, presenting symptoms and patient's preference.

• 한국발생생물학회지:발생과생식
• /
• 제20권3호
• /
• pp.219-225
• /
• 2016

Most of the commercial devices for vitrification are directly immersed into the warming solution (WS) for increasing of warming rate. However, the previous modified cut standard straw (MCS) which has reported is difficult to immerse into the WS. The aim of this study was to investigate whether the long cut straw (LCS) could be useful as a stable tool for vitrified-warmed human blastocysts. A total of 138 vitrified-warmed cycles were performed between November 2013 and November 2014 (exclusion criteria: women ${\geq}38$ years old, poor responder, surgical retrieval sperm, and severe male factor). The artificial shrinkage was conducted using 29-gauge needles. Ethylene glycol and dimethyl sulfoxide (7.5% and 15% (v/v)) were used as cryoprotectants. Freezing and warming were conducted using the LCS tool. The cap of LCS was removed using the forceps in the liquid nitrogen ($LN_2$) and then directly immersed into the first WS for 1 min at $37^{\circ}C$ (1 M sucrose). Only re-expanded blastocysts were transferred after it was cultured in sequential media for 18-20 h. A total of 294 blastocysts were warmed, and all were recovered (100%). Two hundred eighty-five embryos were survived (96.9%). The vitrified-warmed blastocysts of all patients were transferred without any cancellation. We were able to achieve a reasonable implantation (24.2%), following by clinical pregnancy (36.2%), which then continued to ongoing pregnancy (36.2%), and live birth (31.2%). Using LCS is achieved the acceptable rates of survival, pregnancy and live birth. Therefore, the LCS could be considered as a stable and simple tool for human embryo vitrificaton.

• 한국식품과학회지
• /
• 제24권4호
• /
• pp.376-381
• /
• 1992

버섯의 유통기간을 연장하기 위한 방법으로 환경가스조절(modified atmosphere, MA) 저장의 효과를 조사하기 위하여 표고버섯과 느타리버섯을 두께가 $50\;{\mu}m$인 폴리에틸렌 필름으로 포장한 후 $0.5^{\circ}C$에서 저장하였다. 재래식 골판지 상자에 4kg씩 포장된 대조구 버섯은 수분증발, 외관수축, 변색 및 균사발생으로 인하여 유통기간이 $5{\sim}6$일에 불과하였다. MA 저장구의 버섯은 저장 4주 후에도 중량감소가 $1.6{\sim}1.7%$로 낮아 갓 안쪽 주름의 변형이 없었고 갓이 퍼지지도 않았으며 변색도 거의 없었는데 이는 포장내 습도가 포화상태로 유지되고 포장내 산소가 $1.0{\sim}1.3%$, 이산화탄소가 10% 이상으로 유지되어 버섯의 호흡이 억제되었기 때문으로 생각된다. MA 저장 느타리버섯은 조직연화가 품질을 결정하는 가장 중요한 요인이었으며 이를 기준으로 판단한 유통기간은 15일 정도였으며 MA 저장 표고버섯은 갓의 황변이 품질저하의 가장 중요한 요인이었으며 이를 기준으로 판단한 동고의 유통기간은 15일, 화고의 유통기간은 30일 이상이었다.

• Journal of Korean Neurosurgical Society
• /
• 제30권5호
• /
• pp.567-574
• /
• 2001

Objective : As for growth hormone(GH) secreting pituitary adenoma, it's remission should be declared on the basis of satisfactory controlling of the tumor, normalization of hormonal level, and symptomatic improvement of the patient. Several modalities of treatment have been applied and administered, and yet, this disease still remains as inveterate one to be fully treated. The purpose of this study is to evaluate the outcome of gamma knife radiosurgery(GKRS) for GH secreting pituitary adenoma, and to identify various factors affecting the outcome of the treatment. Method : A group of 24 out of 35 patients, treated by Leksell gamma knife unit during the period of March of 1992 through October of 1997, had been observed for more than two years. The mean target volume of microadenoma was $449.3mm^3(range 216-880mm^3)$, and that of macroadenoma was $3183.1mm^3(range 1456-13125mm^3)$. The tumor margin was covered with 50% isodose profile, and mean marginal dose was 25.2Gy(range 15-32.4Gy). The mean number of isocenter was 4.3(range 1-6). The exposed dose to the optic apparatus was less than 8Gy. The mean follow-up period was 37.8months(range 24-102months). Result : No patients showed any increase in the tumor volume during the follow-up period. And definite shrinkage of tumor volume(tumor volume reduction rate, TVRR : more than 50%) was obtained in 10 patients(41.7%). Twenty one patients(87.5%) had reduced hormonal level compared than pre-treatment level. Among them, normalization of the hormonal level was achieved in 12 patients(50%). Clinicoendocrinological remission was seen in 3 patients (12.5%). According to the results of statistical analysis, tumor volume(p=0.016),duration of symptoms(p=0.046), initial GH level(p=0.017), and the invasion of cavernous sinus(p=0.036) were significantly favorable to post-radiosurgical outcome. The TVRR was significantly related to post-radiosurgical reduction of serum GH level. Permanent complication was not seen. Conclusion : The authors concluded that GKRS is a safe and effective treatment modality for acromegaly. To otain the better outcome of GKRS in GH secreting pituitary adenoma, more careful and sophisticated treatment-planning is recommended.

• Journal of Korean Neurosurgical Society
• /
• 제50권4호
• /
• pp.299-303
• /
• 2011

Objective : Brainstem metastases are rarely operable and generally unresponsive to conventional radiation therapy or chemotherapy. Recently, Gamma Knife Radiosurgery (GKRS) was used as feasible treatment option for brainstem metastasis. The present study evaluated our experience of brainstem metastasis which was treated with GKRS. Methods : Between November 1992 and June 2010, 32 patients (23 men and 9 women, mean age 56.1 years, range 39-73) were treated with GKRS for brainstem metastases. There were metastatic lesions in pons in 23, the midbrain in 6, and the medulla oblongata in 3 patients, respectively. The primary tumor site was lung in 21, breast in 3, kidney in 2 and other locations in 6 patients. The mean tumor volume was $1,517mm^3$ (range, 9-6,000), and the mean marginal dose was 15.9 Gy (range, 6-23). Magnetic Resonance Imaging (MRI) was obtained every 2-3 months following GKRS. Follow-up MRI was possible in 24 patients at a mean follow-up duration of 12.0 months (range, 1-45). Kaplan-Meier survival analysis was used to evaluate the prognostic factors. Results : Follow-up MRI showed tumor disappearance in 6, tumor shrinkage in 14, no change in tumor size in 1, and tumor growth in 3 patients, which translated into a local tumor control rate of 87.5% (21 of 24 tumors). The mean progression free survival was 12.2 months (range, 2-45) after GKRS. Nine patients were alive at the completion of the study, and the overall mean survival time after GKRS was 7.7 months (range, 1-22). One patient with metastatic melanoma experienced intratumoral hemorrhage during the follow-up period. Survival was found to be associated with score of more than 70 on Karnofsky performance status and low recursive partitioning analysis class (class 1 or 2), in terms of favorable prognostic factors. Conclusion : GKRS was found to be safe and effective for management of brainstem metastasis. The integral clinical status of patient seems to be important in determining the overall survival time.

• 콘크리트학회논문집
• /
• 제20권3호
• /
• pp.405-412
• /
• 2008

친환경 콘크리트 개발의 의미와 한계를 파악하기 위해 알칼리 활성 경량콘크리트 6배합이 실험되었다. 무시멘트 친환경 결합재를 생산하기 위해 고로슬래그와 분말형 규산나트륨이 각각 모재와 활성화제로 이용되었다. 최대직경 13 mm의 경량골재가 굵은골재로 이용되었으며, 최대직경 5 mm의 경량골재가 천연모래의 용적비로 0, 15, 30, 50, 75 및 100% 치환되었다. 굳지 않은 콘크리트에서는 시간경과에 따른 슬럼프 변화가 측정되었으며, 굳은 콘크리트에서는 재령에 따른 압축강도 발현속도, 할렬인장강도, 파괴계수, 탄성계수, 응력-변형률 관계, 부착강도 및 건조수축 변형률이 측정되었다. 실험된 알칼리 활성 경량콘크리트의 압축강도는 경량 잔골재 치환율이 30% 이상일 때 급격히 감소하였다. 특히 사용된 경량골재의 불연속 입도분포는 콘크리트의 역학적 특성들을 나쁘게 만들었다. 알칼리 활성 경량콘크리트의 역학적 특성들은 보통포틀랜드시멘트 경량콘크리트를 위해 제시된 ACI 318-05 및 EC 2 설계기준 또는 Slate 등의 제안모델들과 비교되었다. 또한 측정된 응력-변형률 관계는 보통포틀랜드시멘트 경량콘크리트의 실험 결과에 근거하여 제시된 Tasnimi의 모델과 비교되었다. 실험 결과와 각 제안 모델들과의 비교는 잘 일치하지 않았다.