• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.1
• /
• pp.99-104
• /
• 2009

In this paper, the drop characteristic of the small aircraft landing gear of SUAV has been analyzed and performed on orifice optimal design for shock absorption efficiency. The SUAV landing gear was simple oleo pneumatic type without metering pin. The landing gear was modelled by MSC ADAMS software. Drop test evaluation was conducted to confirm the analysis model. As a result of correlation between analysis and test results, it was verified that these results were coincided with very well. After confidence review of analysis model through the correlation between test and analysis results, design parametric study was performed by using confirmed analysis model. Optimal orifice size with best efficiency have been decided in this study.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.2
• /
• pp.67-73
• /
• 2012

Structural stability and shock absorption are important properties for corrugated board. In order to maintain structural stability, adhesive properties between top/bottom liners and corrugated medium are not only essential but also important for productivity and product quality. Borax has been an essential ingredient in corrugating adhesive solution. Borax increases viscosity, bonding between starchs and green adhesive bond. The objective of this research is to improving adhesive strength and viscosity stability by adding cross-linking agent instead of borax. Rheology and penetration of main starch gelatinization slurry were affected by borax addition level. Borax increased viscosity and decreased viscosity stability, while cross-linking additives increased viscosity stability and adhesive strength by anchoring effect.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.39 no.3
• /
• pp.419-432
• /
• 2015

This paper examines the protective clothing satisfaction rate of riot policemen. The protective clothing currently in use is the version that underwent enhancement and was distributed in 2009. This version underwent significant enhancements compared to the protective clothing introduced in 1996 in terms of safety and body fitness; however, there is room for further enhancement in terms of activity, thermal comfort and easiness. In this research, a questionnaire survey was conducted on 386 riot policemen working at the Seoul Riot Police Station to study their use of protective clothing and satisfaction rate. The survey questions included safety, activity and body fitness in terms of functionality and comfort as well as easiness and design in terms of wearing comfort. Activity scored the lowest (2.89) in terms of functionality as well as comfort (2.40) that scored the lowest in terms of wearing comfort. It is concluded that, in order to correct deficiencies, the weight of protective clothing must be reduced and design changes must be made to eliminate unnecessary areas in clothing and facilitate faster dressing/undressing. In addition, it is strongly recommended that shock absorption materials be inserted only in vital areas in order to enhance thermal comfort.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.2
• /
• pp.132-143
• /
• 2003

Viscoelastic components for vibration isolation or shock absorption in automobiles, machines and buildings are often subject to a high level of static deformation. From the dynamic design point of view, it is requisite to predict dynamic complex stiffness of viscoelastic components accurately and efficiently. To this end, a systematic procedure for complex modulus measurement of the viscoelastic material under large static deformation is often required in the industrial fields. In this paper, dynamic test conditions and procedures for the viscoelastic material under small oscillatory load superimposed on large static deformation are discussed. Various standard test methods are investigated in order to select an adequate test methodology. The influence of fixed boundary condition in the compression tests upon complex stiffness are investigated and an effective correction technique is proposed. Then the uniaxial tension and compression tests are performed and its results are compared with analysis results from conventional constitutive models.

• Journal of Welding and Joining
• /
• v.31 no.5
• /
• pp.59-63
• /
• 2013

A bendable electronic module has been developed for a mobile application by using a low-cost roll-to-roll manufacturing process. In flexible embedded electronic module, a thin silicon chip was embedded in a polymer-based encapsulating adhesive between flexible copper clad polyimide layers. To confirm reliability and durability of prototype bendable module, the following tests were conducted: Moisture sensitivity level, thermal shock test, high temperature & high humidity storage test, and pressure cooker tester. Those experiments to induce failure of the module due to temperature variations and moisture are the experiment to verify the reliability. Failure criterion was 20% increase in bump resistance from the initial value. The mechanism of the increase of the bump resistance was analyzed by using non-destructive X-ray analysis and scanning acoustic microscopy. During the pressure cooker test (PCT), delamination occurred at the various interfaces of the bendable embedded modules. To investigate the failure mechanism, moisture diffusion analysis was conducted to the pressure cooker's test. The hygroscopic characteristics of the encapsulating polymeric materials were experimentally determined. Analysis results have shown moisture saturation process of flexible module under high temperature/high humidity and high atmosphere conditions. Based on these results, stress factor and failure mechanism/mode of bendable embedded electronic module were obtained.

• Journal of Welding and Joining
• /
• v.32 no.2
• /
• pp.63-69
• /
• 2014

Dual laser heat sources were used for polymer based material joining. An infrared camera and thermocouple DAQ system were used to correlate the temperature distribution to computer simulation. A 50 degree tilted pre-heating laser source was acting as a heating source to promote the temperature to minimize thermal shock by the following a welding heat source. Based on the experimental result, the skin depth was empirically estimated for computer simulation. The offsets of 3mm, 5mm and 10mm split by weld and preheat were effectively used to control the temperature distribution for the optimal laser joining process. The closer offset resulted in an excessive melting or burning caused by sudden temperature rising. The laser power was split by 50%, 75% and 100% of the weld power, and the best results were found at 50% of preheating. To accurately simulate the physical laser beam absorption and joining optical properties were experimentally measured for the computer FEM simulation. The simulation results showed close correlation between theoretical and experimental results. The developed dual laser process is expected to increase productivity and minimize the cost for the final products.

• Steel and Composite Structures
• /
• v.6 no.4
• /
• pp.303-317
• /
• 2006

The connection with combined cross diaphragm is developed for the connection of square CFT column and steel beam and proposed to be used for the frame with asymmetric span length. The structural characteristics of this connection lie in the penetration of the beam flange in the direction of major axis through the column for the smooth flow of stress. The purpose of this study is to analyze the dynamic behavior and stress flow of suggested connection and to evaluate the resistance to shock of connection. Four T-type CFT column-to-beam specimens; two with combined cross diaphragm and the others with interior and through diaphragms, the existing connection types, were made for cyclic load test guided by the load program of ANSI/AISC SSPEC 2002. The results show that the proposed connection is more efficient than existing ones in terms of strength, stress flow and energy absorption and satisfies the seismic performance required in the region of weak/moderate earthquakes.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.8
• /
• pp.661-668
• /
• 2016

Oil deflector prevents oil leakage that occurs in thermoelectric power plant at operating lubricant facilities. Vibration of rotating rotor-induced wear of aluminum tooth in existing oil deflector leads to oil leakage as well as life shortening of the tooth. In this study, an advanced oil deflector was developed for shock absorption and prevention of wear by decreasing clearance (from 0.5 mm to 0.2 mm) between rotor and tooth to minimize oil leakage, and by replacing 2 aluminum teeth in outmost of the oil deflector with hi-performance seal made of engineering plastic. The CFD results were compared between advanced vs. existing oil deflector to determine the amount of oil loss. Structural safety was verified through impact analyses according to the three kinds of engineering plastics, considering cost efficiency, and optimal material of hi-performance seal was chosen.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.15 no.4
• /
• pp.519-526
• /
• 2012

Recently fuel cell is considered to be a new technology that can substitute the ICE(Internal Combustion Engine) as well as overcome environmental issues. In military applications, fuel cell has an unique advantages, which are quietness, namely, stealth. The environmental requirement such as shock and vibration in military application, however, is very severe comparing to civilian demand. Especially, the safety concerning hydrogen storage is the most important problem. Among the candidate methods to store hydrogen, the metal hydride storage is promising method owing to the storage mechanism of chemical absorption of hydrogen to metal hydrides. In this study, the new composition of Ti-Zr type metal hydride(A composition) was suggested and investigated to increase the hydrogen storage capacity. For comparison, the hydrogen charge-discharge properties were investigated with the commercialized Ti-Zr type metal hydride(B composition) using PCT(Pressure-Composition-Temperature) measurement. Also two hydrogen storage cylinders were loaded with each metal hydride and their hydrogen charging and discharging characteristics were investigated. As a result, it was found that the new Ti-Zr type metal hydride has a slightly higher hydrogen storage capacity compared to commercial Ti-Zr type metal hydride.

• Korean Journal of Applied Biomechanics
• /
• v.24 no.2
• /
• pp.131-138
• /
• 2014

The purpose of this study was to analyse the effect of the drop height on lower extremity and lower back kinematics and kinetics during drop landing with the use of raised heel insole. Furthermore we investigated the change that occurred in our body. Joint ROM, eccentric work and contribution to total work were calculated in 11 male college students performing drop landing with 8 motion analysis cameras and 1 forceplate. The result were as follows. First, the ROM and eccentric work were increased in all joints with the increase of the drop height. Second, the ankle ROM and eccentric work were decreased with the use of the insole. Third, the use of the lower back was increased as the use of the ankle decreased with the insole. Based on these results, we can infer that putting on the insole may contribute to chronic injury. We recommend not to use the insole during physical activity.