• Radiation Oncology Journal
• /
• v.20 no.2
• /
• pp.186-192
• /
• 2002

Purpose : Measurement of transmission dose is useful for in vivo dosimetry. In this study, previous algorithm for estimation of transmission dose was modified for use in cases with tissue deficit. Materials and Methods : The beam data was measured with flat solid phantom in various conditions of tissue deficit. New algorithm for correction of transmission dose for tissue deficit was developed by physical reasoning. The algorithm was tested in experimental settings with irregular contours mimicking breast cancer patients using multiple sheets of solid phantoms. Results : The correction algorithm for tissue deficit could accurately reflect the effect of tissue deficit with errors within ${\pm}1.0\%$ in most situations and within ${\pm}3.0\%$ in experimental settings with irregular contours mimicking breast cancer treatment set-up. Conclusion : Developed algorithm could accurately reflect the effect of tissue deficit and irregularly shaped body contour on transmission dosimetry.

• Journal of Radiation Protection and Research
• /
• v.36 no.2
• /
• pp.93-98
• /
• 2011

We induced the activation of melanocytes in the epidermis of C57BL/6 mice by ultraviolet-B (UV-B) irradiation, and observed the effect of an herbal preparation (HemoHIM, HH) on the formation, and decrease of UV-B-induced epidermal melanocytes. C57BL/6 mice were irradiated by UV-B $80\;mJ{\cdot}cm^{-2}$ ($0.5\;mW{\cdot}sec^{-1}$) daily for 7 days, and HH was intraperitoneally, orally or topically applied pre- or post-irradiation. For the estimation of change of epidermal melanocytes, light microscopic observation with dihydroxyphenylalanine (DOPA) stain was performed. Split epidermal sheets prepared from the ear of untreated mice exhibited 13~15 melanocytes${\cdot}mm^{-2}$, and one week after UV irradiation, the applied areas showed an increased number of strongly DOPA-positive melanocytes with stout dendrites. But intraperitoneal, oral or topical treatment with HH before each irradiation interrupted UV-B-induced pigmentation and resulted in a marked reduction in the number of epidermal melanocytes as compared to the number found in UV-B-irradiated, untreated control skin. The number and size of DOPA-positive epidermal melanocytes were also significantly decreased in intraperitoneally injected or topically applicated group after irradiation with HH at 3rd and 6th weeks after irradiation. The present study suggests the HH as inhibitor of UV-B-induced pigmentation, and depigmenting agent.

• Journal of Bio-Environment Control
• /
• v.22 no.2
• /
• pp.87-90
• /
• 2013

The average annual and winter ambient air temperatures in Korea have risen by $0.7^{\circ}C$ and $1.4^{\circ}C$, respectively, during the last 30 years. Due to climate change, the occurrence of abnormal weather conditions has become more frequent, causing damage to vegetable crops grown in Korea. Hot pepper, chinese cabbage and radish, the three most popular vegetables in Korea, are produced more in the field than in the greenhouse. It has been a trend that the time for field transplanting of seedlings is getting earlier and earlier as the spring temperatures keep rising. Seedlings transplanted too early in the spring take a longer time to resume the normal growth, because they are exposed to suboptimal temperature conditions. This experiment was carried out to figure out the change of cellular tissue of chinese cabbage under the condition of low temperature to provide the information regarding the coming climatic change, on the performance of 'Chunkwang' chinese cabbage during the spring growing season. In our study, plant height, number of leaf, chlorophyll and leaf area was lower at the open field cultivation than heating house treatment after transplanting 50 days. Especially in fresh weight, compared with heating treatment, open field and not heated treatment were notably low with the 1/3 level. Of damage symptoms due to low temperature cabbage leaves about 10 sheets when $-3.0^{\circ}C$ conditions in chinese cabbage was a little bit of water soaking symptoms on the leaves. $-7.4^{\circ}C$ under increasingly severe water soaking symptoms of leaf turns yellow was dry. Microscopy results showed symptoms of $-3.0^{\circ}C$ when the mesophyll cell of palisade tissue and spongy tissue collapse, $-7.4^{\circ}C$ palisade tissue and spongy tissue was completely collapsed. The result of this study suggests that the growers should be cautioned not to transplant their chinese cabbage seedlings too early into the field, and should be re-transplanting or transplanting other plants if chinese cabbage are exposed to suboptimal temperature conditions ($-3.0^{\circ}C$ or $-7.4^{\circ}C$).

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.3 no.2
• /
• pp.1-15
• /
• 1983

This paper has concentrated on estimating the possibility and mathematical analysis for the application of BFB to the treatment of nightsoil with low dilution rate. The experiment for the study of this purpose was conducted by continuous type reactor at $20^{\circ}C$, varying F/M ratio from 0.12 to 0.37 and dilution ratio from 2 to 10, and in it provided matted reticulated polypropylene sheets for the solid supports. The obtained results showed that the application of BFB to the treatment of nightsoil would be more effective than any other biological treatment process. Also, it has observed that the optimum dilution ratio was about 5 times and the optimum HRT was about 17 hours, and then it was estimated that the reactor volume and the quantity of weak water could be reduced to the extent of 70 percent and 80 percent. The experimental results of BFB could be analysed by the mathematical models applied to complete mixing activated sludge process. The substrate removal rates which were obtained by McKinney's($K_m$) and EcKenfelder's($K_e$) equation was 1.784/hr and $2.0{\times}10l/mg{\cdot}day$, and substrate was removed very rapidly compared to those of conventional type biological treatment processes. The biomass yield coefficient($a_5$), the endogeneous respiration rate(b), the synthesis oxygen demand rate($a{_5}^{\prime}$), and the endogeneous respiration oxygen demand rate(b') were 0.349, 0.0237/day, 0.495 and 0.0336, respectively.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2000.04a
• /
• pp.9-10
• /
• 2000

An important business-field of world-wide steel-industry is the coating of thin metal-sheets with zinc, zinc-aluminum and aluminum based materials. These products mostly go into automotive industry. in particular for the car-body. into building and construction industry as well as household appliances. Due to mass-production, the processing is done in large continuously operating plants where the mostly cold-rolled metal-strip as the substrate is handled in coils up to 40 tons unwind before and rolled up again after passing the processing plant which includes cleaning, annealing, hot-dip galvanizing / aluminizing and chemical treatment. In the liquid Zn, Zn-AI, AI-Zn and AI-Si bathes a combined action of corrosion and wear under high temperature and high stress onto the transfer components (rolls) accounts for major economic losses. Most critical here are the bearing systems of these rolls operating in the liquid system. Rolls in liquid system can not be avoided as they are needed to transfer the steel-strip into and out of the crucible. Since several years, ceramic roller bearings are tested here [1.2], however, in particular due to uncontrollable Slag-impurities within the hot bath [3], slide bearings are still expected to be of a higher potential [4]. The today's state of the art is the application of slide bearings based on Stellite\ulcorneragainst Stellite which is in general a 50-60 wt% Co-matrix with incorporated Cr- and W-carbides and other composites. Indeed Stellite is used as the bearing-material as of it's chemical properties (does not go into solution), the physical properties in particular with poor lubricating properties are not satisfying at all. To increase the Sliding behavior in the bearing system, about 0.15-0.2 wt% of lead has been added into the hot-bath in the past. Due to environmental regulations. this had to be reduced dramatically_ This together with the heavily increasing production rates expressed by increased velocity of the substrate-steel-band up to 200 m/min and increased tractate power up to 10 tons in modern plants. leads to life times of the bearings of a few up to several days only. To improve this situation. the Mechanical Alloying (MA) TeChnique [5.6.7.8] is used to prOduce advanced Stellite-based bearing materials. A lubricating phase is introduced into Stellite-powder-material by MA, the composite-powder-particles are coated by High Energy Milling (HEM) in order to produce bearing-bushes of approximately 12 kg by Sintering, Liquid Phase Sintering (LPS) and Hot Isostatic Pressing (HIP). The chemical and physical behavior of samples as well as the bearing systems in the hot galvanizing / aluminizing plant are discussed. DependenCies like lubricant material and composite, LPS-binder and composite, particle shape and PM-route with respect to achievable density. (temperature--) shock-reSistibility and corrosive-wear behavior will be described. The materials are characterized by particle size analysis (laser diffraction), scanning electron microscopy and X-ray diffraction. corrosive-wear behavior is determined using a special cylinder-in-bush apparatus (CIBA) as well as field-test in real production condition. Part I of this work describes the initial testing phase where different sample materials are produced, characterized, consolidated and tested in the CIBA under a common AI-Zn-system. The results are discussed and the material-system for the large components to be produced for the field test in real production condition is decided. Outlook: Part II of this work will describe the field test in a hot-dip-galvanizing/aluminizing plant of the mechanically alloyed bearing bushes under aluminum-rich liquid metal. Alter testing, the bushes will be characterized and obtained results with respect to wear. expected lifetime, surface roughness and infiltration will be discussed. Part III of this project will describe a second initial testing phase where the won results of part 1+11 will be transferred to the AI-Si system. Part IV of this project will describe the field test in a hot-dip-aluminizing plant of the mechanically alloyed bearing bushes under aluminum liquid metal. After testing. the bushes will be characterized and obtained results with respect to wear. expected lifetime, surface roughness and infiltration will be discussed.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.2 no.2
• /
• pp.105-133
• /
• 1969

The stability of three major pigments in lavers, namely chlorophylls, carotenoids, and phy-cobilins, during processing and storage was studied. The results of the pigment retention in fresh lavers during storage at low temperatures, of heat lability during heat treatment, and of the pigment loss during storage are summarized as follows: 1. The contents of chlorophyll a, xanthophyll (lutein+zeaxanthin), and carotene ($\alpha-+\beta-carotene$) averaged 1,525, 627, and $409{\mu}g/g$ of dry samples respectively The comparative composition of four carotenoids, lutein, $\beta-carotene$, zeaxanthin, and $\alpha-carotene$, was 35.9, 33.7, 12.2, and $5.8\%$ respectively. 2. In storage of fresh lavers at room ternperature ($20-25^{\circ}C$), 2 to $5^{\circ}C$, and $-15^{\circ}C$, the pigments generally were retained more at 2 to $5^{\circ}C$ than others while carotene only showed more retention at $-15^{\circ}C$ than at 2 to $5^{\circ}C$. Phycocyanin tended to decrease more rapidly than phyco-erythrin at low temperatures. 3. In regard to heat treatment of both dried and wet materials at 40, 60, 80, $100^{\circ}C$ respectively, the pigments were more stable at lower temperatures than at higher temperatures in both cases of materials. Carotenoids were retained more in wet materials than in the sun dried. Xanthophylls showed higher heat stability than carotenes. Phycoerythrin was considered more heat labile than phycocyanin, particularly at higher temperatures. 4. In storage of heat treated lavers for 50 days at room temperature, the retention of pigments appeared differently in accordance with the temperatures of treatment The materials treated at $60^{\circ}C$ showed better relention of pigments than those treated at the other temperatures. Degradation rate of xanthopllylls, carotenes, and phycobilins was decreased in the materials treated at higher temperatures, showing a tendency of great pigment retention even for a long period storage. Chlorophyll il was retained more in sun dried materials whereas xanthophyll and carotene were retained more in the wet. 5. In order to maintain a higher pigment stability during storage, the materials must be treated at $60^{\circ}C$ in a dryer with rapid ventilation until the moisture level reaches about $6.0\%$. In case of treatment at a higher temperature than $60^{\circ}C$, they must be treated for a short period of time to minimize pigment degradation by heat. 6. The lavers treated with the solutions of pH around 7.8 showed a higher retention of chlorophyll a. When treated with the solutions of algal extracts such as agar and alginic acid, uniform layer of laver sheets and better surface gloss of dried layers were obtained.

• The Journal of Korean Society for Radiation Therapy
• /
• v.22 no.2
• /
• pp.131-134
• /
• 2010

Purpose: TOMO therapy treatment for a relatively long run Beam time and temperature-sensitive detector, such as CT clinics in optimal temperature ($20~21^{\circ}$) to maintain a constant temperature in addition to its own Chamber Cooling system is activating. TOMO This clinic has been reduced in the patients' body temperature to keep the sheets and covers over the treated area. Therefore, these materials for any changes in the organization gives the dose were analyzed. Materials and Methods: To compare changes in the organization Dose Phantom cheese (Cheese Phantom) were used, CT-simulation taking the center point of the cheese phantom PTV (Planning Target Volume, treatment planning target volume) by setting Daily dose 200 cGy, 3 meetings planned treatment. PTV, PTV +7 cm, PTV +14 cm, the total count points on the phantom using the Ion chamber cover without any substance to measure the dose, and one of the most commonly used treatment, including the frequently used four kinds of bedding materials (febric 0.8 mm, gown 1.4 mm, rug, 3.3 mm, blanket 13.7 mm) and covered with a phantom and the dose measured at the same location were analyzed 3 times each. Results: PTV, PTV +7 cm, PTV +14 cm from the point of any substance measured in the state are covered with four kinds of materials (fabric, gown, rug, blanket) was measured in the covered states and compares their results, PTV respectively -0.17%, -0.44%, -0.53% and -0.9% change, PTV +7 cm, respectively -0.04%, +0.07%, +0.06%, +0.07%, were changed, PTV +14 cm, respectively 0%, -0.06%, -0.02%, +0.6%, respectively. Conclusion: These results TOMO treatment to patients to maintain their body mass by using PTV thickness of the material decreased in proportion to. PTV +7 cm, but showed slight changes in the point, PTV +14 cm at the point of the dose was increased a little. Sejijeom all the difference in treatment tolerance ${\pm}3%$ range, this is confirmed in the coming treatment will not affect the larger should be considered.

• Korean Security Journal
• /
• no.2
• /
• pp.259-289
• /
• 1999

The Security Industry has dynamic working conditions. So this study intends to find the advisable direction for the reduction of accidents. To achieve the aim, the investigation of documents and the examinations of actual proofs have been done to figure the theoretical background and to see the basic knowledge of security industry. The questionnaire was composed of two question sheets to search real data and actual proofs, with making targets of pure security organization and personnel. The one consists of 9 questions to find the scale and extent of security organizations and the population and character of security personnel, and the other 25 questions in 3 major areas to analyze the causes, the frequency rates, the factors, and the condition of accidents. The period of survey was July 15th to October 15th in 1997 by mail/telephone/interview. The questionnaires were efficiently returned from 102 different organizations including the public security groups of Seoul Metropolitan Police Bureau and so on, with the information of 8,222 persons having worked for Korean Security Industry in 1996. So being based on the reality, some meaningful facts were found, and were compared with the national statistics of the Government. This study is made up of 5 chapters : in the 1st chapter the motivation, the object, the method, the direction and the limitation of the approach were presented ,in the 2nd chapter the theoretical background were inferred ; in the 3rd chapter the collected data of accidents in Korean Security Industry were analyzed and explained on the base of the questionnaires , in the 4th chapter the advisable facts connected with preventing accidents were mentioned ; in the last the conclusion were stated. With the replies of 102 different organizations including the information of 8,222 persons in 1996, the main facts found or analyzed through this study are as follows. Firstly, accident is an unpredictable and occasional event. It occurs to man and/or thing, but the frequency rate of accidents in Korean Government and other Institutes has been calculated and evaluated only in the point of the accident related with man. Secondly, the factors of accidents are firstly relevant to the way preventing accidents in Security Industry in Korea. However the frequency rate is academically calculated and evaluated by at once man(population) and hour(time). But the Government has done the rate only by man(population). This can be improper and inaccurate rates. Thirdly, the confused concept of security is used in Korean Government, academic society, corporation and so on. Therefore the detailed formation of the concept is needed for the development of Security Industry in Korea. Fourthly, security organizations can be classified into 'public security(public law enforcement)' and 'private security' according to its identification, and furthermore 'private security' can be divided into 'facilities-guard service', 'body-guard service', and 'patrol service' according to its major role. Fifthly, in the viewpoint of the number of both organization and population,'facilities-guard service' is centered in Korean 'private security'. According to the analyzed results of the questionnaires in this study, the frequency rate of accidents of Korean Security Industry is 0.43(%) totally in 1996 : 'facilities-guard service' 0.54(%), 'body-guard service' 0.12(%), and 'patrol service' 0.21(%) in 'private security', and 'public security' 0.20(%). With regard to the accident frequency rate of organization and population, 'facilities-guard service' is the highest. The accident frequency rate of population in 'facilities-guard service' organization ranges dispersively from 0.20(%) to 11.11(%). Sixthly, the accidented rate of workers having serviced for under one year is 57.6(%). This can mean that the main factor of accidents in Korean Security Industry is the lack of role-understanding and training/education. And another factor can be found on the time of accident occurrence. Many accidents have been occurred on the relaxed points like as just after lunch and morning rush-hour. Lastly, the major advisable facts related to preventing accidents are as follows : The workers who are over fifty years old in 'facilities-guard service' organization need to be educated for preventing accidents ; It is desirable that the training and education to prevent accidents should be practiced in the time of pre-service ; As the style of accidents and the age of the accidented are not same according to major service area('public security' and 'private security' : 'facilities-guard service', 'body-guard service', and 'patrol service'), the plans to prevent accidents must be different and various. However fracture and bruise are general accidents in Korean Security Industry ; Workers must care about traffic accident and violent fall ; It seems that the grouped working with other two persons will reduce accident occurrence possibility rather than individually single working.

• Tuberculosis and Respiratory Diseases
• /
• v.48 no.3
• /
• pp.357-364
• /
• 2000

Background : Complicated exudative pleural fluid collections have traditionally been treated by either closed tube thoracostomy drainage or by open surgical drainage. Complete drainage is important in order to control pleural sepsis, restore pulmonary function, and entrapment. Recently intracavitary fibrinolytic therapy has been advocated as a method to facillitate drainage of complicated exudative pleural effusion and to allow enzymatic debridemant of the restrictive fibrinous sheets covering the pleural surface. The purpose of this study is to prospectively evaluate the effects of image-guided catheter drainage with high dose urokinase(UK) instillation in the treatment of complicated pleural effusions. Patients : Twenty complicated pleural effusion patients that poorly respond to image-guided drainage were allocated to receive UK. There were 8 pneumonia and 12 tuberculosis. Methods : Drugs were diluted in 250 mL normal saline and were infused intrapleurally through the chest tube or pig-tail catheter in a daily dose of 250,000 IU of UK. Response was assessed by clinical outcome, fluid drainage, chest radiography, pleural ultrasound and/or computed tomography. Results : The mean UK instillation time was $1.63{\pm}0.10$. The mean volume drained UK instillation was $381.3{\pm}314.4\;mL$, and post-UK was $321.6{\pm}489.5\;mL$. The follow up duration after UK therapy was mean $212.9{\pm}194.5$ days. We had successful results in 19 cases (95.0%). There were 12 pleural thickenings (60.0%), 2 markedly decreased effusions (10.0%) and 5 cases of no thickening or effusion. There was recurrence after treatment in only one patient(5%) with complicated pleural effusiondue to tuberculosis. Conclusions : Image-guided drainage with high dose UK instillation (250,000 U/day) in complicated pleural effusion is a safe and more effective method than closed thoracostomy drainage. And this management, in turn, can obviate surgery in most cases.

• Journal of dental hygiene science
• /
• v.7 no.3
• /
• pp.147-152
• /
• 2007

The purpose of this study was to examine how dental-care institutions responded to discontented customers and how much they provided grievance service and tried not to displease customers. After a survey was conducted on dental-care institutions from January 20 through February 20, 2007, the answer sheets from 206 respondents were analyzed with SPSS WIN 12.0 program, except four incomplete ones. The findings of the study were as follows: 1. 32.5 percent of the respondents were aware of grievance service, and 64.6 percent actually provided no grievance service. 94.7 percent had ever met customers who made a complaint. 2. The most common grievance of medical consumers was that it took long time to receive treatment and to wait for it. The second most dominant complaint was that the treatment they received was beyond the coverage of health-care insurance(30.6%). An insufficient medical explanation was the third most common grievance(6.3%), followed by excessive medical bills(5.8%). The most dominant number of monthly grievance case was one to ten(91.3%). As for how customers voiced their complaints, the largest number of customers talked employees about that in person(88.2%), and dental hygienists were mainly identified as a person who handled their grievance(56.8%). Concerning how the dental-care institutions responded to complaining customers, the largest number of the institutions took an immediate action(34.5%), and the second largest group took a measure after investigating the disposition of discontented patients(30.0%). The third greatest group just made an excuse(11.1%), and the fourth greatest group directed active efforts into taking care of complaining customers by offering grievance service (7.0%). 3. The dental-care institutions got a mean of 3.02 in grievance handling. The institutions that dental hygienists were in charge of grievance handling statistically significantly better responded to discontented customers than the others that receptionists were in charge of that(p < .01). The institutions that had no monthly grievance cases took care of discontented customers statistically significantly better than the institutions that faced one to ten grievance cases or 11 or more cases (p < .05). 4. The dental-care institutions got a mean of 2.59 in providing service of preventing customers from being dissatisfied. The institutions located in Seoul, Incheon and Gyeonggi province provided statistically significantly better service of that kind than the others located in the other regions(p < .01). And the dental-care institutions that dental hygienists were in charge of grievance handling offered statistically significantly better service of that kind than the dental-care institutions that receptionists were in charge of it(p < .05).