• 한국전기전자재료학회논문지
• /
• 제11권3호
• /
• pp.195-202
• /
• 1998

The LPCVD system of batch type for the massproduction of semiconductor fabrication has a problem of phosphorous concentration uniformity in the boat. In this paper we study an improvement of the uniformity for phosphorous concentration and sheet resistance. These property was improved by using the nitrogen process and modified long nozzle for gas injection tube in the doped polysilicon deposition system. The phosphorous concentration and its uniformity for polysilicon film are measured by XRF(X-ray Fluorescence) for the conventional process condition and nitrogen process. In conventional process condition, the phosphorous concentration, it uniformity and sheet resistance for polysilicon film are in the range of 3.8~5.4$\times$10\ulcorner atoms/㎤, 17.3% and 59~$\Omega$/ , respectively. For the case of nitrogen process the corresponding measurements exhibited between 4.3~5.3$\times$10\ulcorner atoms/㎤, 10.6% and 58~81$\Omega$/ . We find that in the nitrogen process the uniformity of phosphorous concentration improved compared with conventional process condition, however, the sheet resistance in the up zone of the boat increased about 12 $\Omega$/ . In modified long nozzle, the phosphorous concentration, its uniformity and sheet resistance for polysilicon films are in the range of 4.5~5.1$\times$10\ulcorner atoms/㎤, 5.3% and 60~65$\Omega$/ respectively. Annealing after $N_2$process gives the increment of grain size and the decrement of roughness. Modification of nozzle gives the increment of injection amount of PH$_3$. Both of these suggestion result in the stable phosphorous concentration and sheet resistance. The results obtained in this study are also applicable to process control of batch type system for memory device fabrication.

• Current Photovoltaic Research
• /
• 제2권4호
• /
• pp.147-151
• /
• 2014

A boron doping process using a boron tri-bromide ($BBr_3$) as a boron source was applied to form a $p^+$ emitter layer on an n-type mono-crystalline CZ substrate. Nitrogen ($N_2$) gas as an additive of the diffusion process was varied in order to study the variations in sheet resistance and the uniformity of doped layer. The flow rate of $N_2$ gas flow was changed in the range 3 slm~10 slm. The sheet resistance uniformity however was found to be variable with the variation of the $N_2$ flow rate. The optimal flow rate for $N_2$ gas was found to be 4 slm, resulting in a sheet resistance value of $50{\Omega}/sq$ and having a uniformity of less than 10%. The process temperature was also varied in order to study its influence on the sheet resistance and minority carrier lifetimes. A higher lifetime value of $1727.72{\mu}s$ was achieved for the emitter having $51.74{\Omega}/sq$ sheet resistances. The thickness of the boron rich layer (BRL) was found to increase with the increase in the process temperature and a decrease in the sheet resistance was observed with the increase in the process temperature. Furthermore, a passivated emitter solar cell (PESC) type solar cell structure comprised of a boron doped emitter and phosphorus doped back surface field (BSF) having Ni/Cu contacts yielding 15.32% efficiency is fabricated.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.15-16
• /
• 2007

The high efficiency and low cost solar cells in order to it applied a dopant pastes diffusion process. The dopant pastes diffusion process which it uses is easily applied in screen-printing solar cells output line. in this paper, it used the Ferro 99-038 phosphorus diffusion pastes source and it analyzed a sheet resistance and a uniformity degree. And it knew the quality of the sheet resistance which it follows in temperature and time condition. The temperature variable it let and it fixed the time in 7 minutes. It will be able to measure the sheet resistance of $40({\Omega}/sq),\;30({\Omega}/sq),\; 20({\Omega}/sq)$. also average uniformity of the sheet resistance was below 5%.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.429-429
• /
• 2012

To investigate the gettering effect of B-doped n-type monocrystalline silicon wafer, we made the p-n junction by diffusing boron into n-type monocrystalline Si substrate and then oxidized the boron doped n-type monocrystalline silicon wafer by in-situ wet and dry oxidation. After oxidation, the minority carrier lifetime was measured by using microwave photoconductance and the sheet resistance by 4-point probe, respectively. The junction depth was analyzed by Secondary Ion Mass Spectrometry (SIMS). Boron diffusion reduced the metal impurities in the bulk of silicon wafer and increased the minority carrier lifetime. In the case of wet oxidation, the sheet resistance value of ${\sim}46{\Omega}/{\Box}$ was obtained at $900^{\circ}C$, depostion time 50 min, and drive-in time 10 min. Uniformity was ~7% at $925^{\circ}C$, deposition time 30 min, and drive-in time 10 min. Finally, the minority carrier lifetime was shown to be increased from $3.3{\mu}s$ for bare wafer to $21.6{\mu}s$ for $900^{\circ}C$, deposition 40 min, and drive-in 10 min condition. In the case of dry oxidation, for the condition of 50 min deposition, 10 min drive-in, and O2 flow of 2000 SCCM, the minority carrier lifetime of 16.3us, the sheet resistance of ${\sim}48{\Omega}/{\Box}$, and uniformity of 2% were measured.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.233-233
• /
• 2010

It is important to form the n+ emitter layer for generating electric potential collecting EHP(Electron-Hole Pair). In this paper the formation on the n+ emitter layer of silicon wafer has been made with respect to uniformity of shallow diffusion from a liquid source. The starting material was crystalline silicon wafers of resistivity $0.5{\sim}3\{Omega}{\cdot}cm$, p-type, thickness $200{\mu}m$, direction[100]. The formation of n+ emitter layer from the liquid $POCl_3$ source was carried out for $890^{\circ}C$ in an ambient of $N_2:O_2$::10:1 by volume. And than each conditions are pre-deposition and drive-in time. It has been made uniformity of at least. so, the average of sheet resistance was about 0.12%. In this study, sheet resistance was measured by 4-point prove.

• 한국전기전자재료학회논문지
• /
• 제32권2호
• /
• pp.147-150
• /
• 2019

There is a need for the development of transparent conductive materials that are economical and environmentally friendly with exhibit low resistivity and high transmittance in the visible spectrum. In this study, the deposition rate and uniformity of Al-doped ZnO-thin films were improved by changing the Z-motion of the sputtering system. The deposition rate and the uniformity were determined to be 3.44 nm/min and 1.23%, respectively, under the 10 mm Z-motion condition. During $O_2$ plasma treatment, the intrusion-type metal elements in the thin film were reduced, which contributed to an oxygen vacancy reduction in addition to structural stabilization. Moreover, the sheet resistance was more easily saturated.

• 한국자기학회지
• /
• 제12권6호
• /
• pp.224-230
• /
• 2002

직경 200mm의 실리콘 기판에 균일한 코발트 금속박막을 증착하는 DC-스퍼터 장비에서 공정변수는 증착온도, 증착압력, DC power로 하고 종속변수(response)는 면저항, 면저항 균일도로 하는 '||'&'||'quot;통계적 실험방법'||'&'||'quot;을 채택한 실험을 수행하여 Co 박막의 공정 특성에 대해 다음과 같은 결과를 얻었다 '||'&'||'quot;통계적 실험방법'||'&'||'quot;을 이용한 Co박막의 공정 특성을 조사하는 본 실험에서 면저항과 면저항 균일도는 0.05 이하의 significance수치. 낮은 RMS error, 0.91 이상의 R-sq수치로부터 실험의 우수한 신뢰성을 확인하였다. 면저항에 대한 공정변수의 영향성은 증착온도가 -1.83$\Omega$/$\square$의 감소효과, 증착압럭이 1.17$\Omega$/$\square$의 증가 효과. DC power가 -0.65$\Omega$/$\square$의 감소 효과로 실험 구간에서 일정한 경향의 영향성을 보였으며, 면저항 균일도에서는 증착온도에 의해 $25^{\circ}C$~147$^{\circ}C$에서 -4.04%의 감소로 증착온도에 가장 민감함을 확인하였다. Co 박막의 최적 증착 조건은 증착온도 $25^{\circ}C$, 증착압력 12mTorr, DC power 1500 W로 예상되었다.

• 대한전자공학회논문지
• /
• 제25권9호
• /
• pp.1051-1059
• /
• 1988

In this study, we developed a proto-type RTP equipment by using tungsten halogen lamps. The system has been designed utilizing the result of the numerical analysis of the reactor. In order to analyze the system performance, experiments for activation of implanted atoms and oxidation process were performed. As a result, we obtained 2-3% uniformity in sheet resistance and 2-4% uniformity in oxide thickness, although after a long time process at high temperatures slip lines and warpage of the wafer have been observed.

• 한국진공학회지
• /
• 제2권4호
• /
• pp.480-485
• /
• 1993

Factros considered building the magnetron sputtering system for TFT LCD (thin film transistor liquid crystal display0 metallization were thin film thichnes uniformity, temperature uniformity and the pressure gradient of sputtering gas flow in vacuum chamber, base pressure, and the stability fo the carrier moving . The system was consisted of a deposition chamber, a pre-heating chamber, a RF-precleaning chamber and a load/unload lock chamber. The system was designed to handle a substrate with dimension of 400$\times$400mm. The temperautre uniformity of a heater table developed showed $250 ^{\circ}C\pm$5% accuracyon the substrate glass. A base pressure of 1.8 $\times$10-7 torr was obtained after 24 hours pumping with a cryo pump. After an aluminum target was installed in a sputtering source and the film wa sdeposited on the glass, the uniformity, reflectivity and sheet resistance of the deposited film were measured.

• Journal of Korean Vacuum Science & Technology
• /
• 제3권2호
• /
• pp.101-106
• /
• 1999

The main consideration factor to design a magnetron of the sputtering system for TFT-LCD metallization is high sheet resistance (Rs) uniformity which is provided by the high target erosion and high current efficiency. The present study has developed a rectangular magnetron for TFT-LCD to bve considered full target erosion and high film uniformity. After an aluminum-2 at.% and alloy target was installed in a magnetron source and the film was deposited on the glass of 600${\times}$720 mm, the Rs uniformity of the deposited film was measured as functions of the magnet tilt and magnet scanning configuration. And the target erosion profile was observed with the target voltage. When sputtered at 4mtorr and 10kW, the magnet tilt for the high Rs uniformity of 8.38% was 7mm. The plasma voltage at the dwell home and end for full-face target erosion, when scanned the magnetron was 120% compared to the mean voltage of the other area.