• 한국세라믹학회지
• /
• 제36권2호
• /
• pp.107-115
• /
• 1999

용융탄산염 연료전지(Molten Carbonate Fuel Cell)용 알루미나 화이버 강화 ${\gamma}$-LiAlO2 매트릭스의 적층방법에 따른 미세구조 변화 및 강도 증진 효과에 대하여 연구하였다. 테이프 캐스팅법으로 제조한 green sheet 2장을 45$^{\circ}C$에서 1kg/$ extrm{cm}^2$의 압력으로 1분간 hot pressing 하여 제조한 적층 매트릭스와 double casting 시 1단계 캐스팅한 green sheet를 3.5 시간 정도 건조한 뒤 2 단계 캐스팅 하여 제조한 적층 매트릭스의 기공율은 모두 50% 이상이었다. 알루미나 화이버 강화 적층 매트릭스의 강도는 비적층 매트릭스(115gf/$ extrm{mm}^2$)에 비해 70% 이상 증진되었으며 적층에 의해 화이버 배향성에 따른 강도의 편향성을 제거할 수 있었다. Triple casting에 의한 적층 메트릭스의 강도는 double casting 시에 비해 약간 증진되었으나 캐스팅 방향에 따른 강도의 편향성이 존재할 뿐만 아니라 기공율도 50% 이하였다. Double casting에 의한 적층 매트릭스의 강도 (195 gf/$\textrm{mm}^2$)는 hot pressing 하여 제조한 매트릭스 (212gf/$\textrm{mm}^2$)에 비해 약간 낮지만 MCFC 매트릭스 제조공정 면에서 double casting 법이 효율적인 적층공정으로 평가되었다.

• 열처리공학회지
• /
• 제34권3호
• /
• pp.122-129
• /
• 2021

This study focuses on the microstructural development of 99% magnesium alloy sheet manufactured using twin roll casting (TRC) process. Herein, a plate with a thickness of 5 mm was manufactured using the TRC process, homogenization heat treatment was performed at 400℃ for 2-32 h, and finally, the change in microstructure was evaluated via optical microscopy and textural analysis. The results suggest that the plate manufactured using the TRC process was not destroyed and was successfully rolled into a plate. Microscopic observation suggested that the dendritic cast structure was arranged along the rolling direction. And the central layer of the rolled plate, where was present in a liquid state at the beginning of rolling, solidified later during the TRC process to form central segregation. The initial cast structure and inhomogeneous structure of the plate were recrystallized by homogenization heat treatment for only 2 h, and it was confirmed that the segregated part of the central layer became homogeneous and recrystallization occurred. Grain growth occurred as the heat treatment time increased, and secondary recrystallization occurred, wherein only some grains were grown. The textural analysis, which was conducted via X-ray diffraction, confirmed that the relatively weak basal plane texture developed using the TRC process was formed into a random texture after heat treatment.

• Design & Manufacturing
• /
• 제6권1호
• /
• pp.95-100
• /
• 2012

In this study, a novel Cu composite sheet with embedded high electric conduction path was developed as another alternative for the interconnect materials possessing high electrical conductivity as well as high strength. The Cu composite sheet was fabricated by forming Ag conduction paths not within the interior but on the surface of a high strength Cu substrate by damascene electroplating process. As a result, the electrical conductivity increased by 40% thanks to mesh type Ag conduction paths, while the ultimate tensile strength decreased by 20%. The interfacial fracture resistance of Cu composite sheet prepared by damascene electroplating increased by above 50 times compared to Cu composite sheet by conventional electroplating. For feasibility test for practical application, a leadframe for LED module was manufactured by a progressive blanking and piercing processes, and the blanked surface profile was evaluated as a function of the volume fraction of Ag conduction paths. As Ag conduction path became finer, pressing formability improved.

• 한국주조공학회지
• /
• 제30권5호
• /
• pp.187-195
• /
• 2010

In this study, in order to obtain a useful guide line for design and production of automotive heat exchanger components made of 4343/3003/4343 aluminum clad sheets, it was aimed to improve the understanding about the grain refinement effect on brazing characteristic of the clad sheets. Al-10Ti master alloy was used for grain refinement of 3003 core alloy, and the Ti inoculation level was systematically changed up to 0.1 wt%. The three-layer aluminum clad sheets were fabricated by hot roll bonding process. The effect of grain refinement on brazing characteristic of the clad sheets was investigated by evaluating wettability, bonding strength and sagging resistance.

• 한국세라믹학회지
• /
• 제33권11호
• /
• pp.1267-1275
• /
• 1996

Green sheet was prepared by tape casting in the composition of (1-x)Pb(Mg1/3Nb2/3)O3-PbTiO3 system using Pb(Mg1/3Nb2/3)O3 and PbTiO3 synthesized with PbO, Nb2O5 MgO and TiO2 The densest green sheet was obtained in the weight ratio 70:30 of powder to binder. Green sheet wasmultilayered in metal mould and formed into lamination at 7$0^{\circ}C$, 300kg/cm2 The lamination was sintered at 110$0^{\circ}C$ 2hr, Dielectric constant and Curie temperature of disc type sintered body was highered with increasing the amount of PbTiO3 and was in the range of 19000-21000, -7~45$^{\circ}C$ respectively. Green and sintered relative density of lamination was 61% and 95% respectively.

• 소성∙가공
• /
• 제15권3호
• /
• pp.232-240
• /
• 2006

Magnesium alloys are expected to be widely used fur the parts of structural and electronic appliances due to their lightweight and EMI shielding characteristics. While the die casting has been mainly used to manufacture the parts from the magnesium alloys, the press forming is considered as an alternative to the die casting for saving the manufacturing cost and improving the structural strength of the magnesium alloy parts. However, the magnesium alloy has low formability at room temperature and therefore, in many cases, forming at elevated temperatures is necessary to obtain the required material flow without failure. In the present study, square cup deep drawing tests using the magnesium alloy AZ31 sheet were experimentally conducted at various elevated temperatures as well as room temperature, and the corresponding finite-element simulations, which calculated the damage evolution based on the Oyane's criterion, were conducted using the stress-strain relations from the tensile tests at various temperatures. The formability predictability by the finite-element analysis was investigated by comparing the predicted damage distributions over the deformed AZ31 sheet at elevated temperatures with the corresponding experimental deformations with failures.

• 소성∙가공
• /
• 제19권6호
• /
• pp.378-386
• /
• 2010

Nowadays there has been great interest in using heat treated cast material for press dies due to several advantages like reduction in die production costs. However, in hot press forming processes H13 forged tool steel is mostly used. Cooling performance of dies in hot press forming processes is considered as an important factor of study and also the IHTC parameter between cast material die and sheet metal should be considered as an essential. In the present study, the IHTC was calculated for the sheet metal in the hot press forming process with cast and forged material dies. The temperature measurements were performed for the sheet metal, casting and forged material dies by applying various contact pressure in hot press forming. IHTC was calculated and studied by adopting the inverse heat convection method in DEFORM-2D. Each IHTC was considered as a function of contact time and contact pressure. The experimental data were compared with calculated data obtained from the proposed equation and references.

• 마이크로전자및패키징학회지
• /
• 제9권2호
• /
• pp.19-25
• /
• 2002

저온소결기판을 위하여 green sheet를 제조하기 위한 조성으로 $Li_2$O.MgO. $MgF_2$.$SiO_2$.$B_2O_3$를 기초 조성으로 선정하였다. 조합 후 용융하여 만들어진 모유리는 열분석을 통하여 최적 핵형성 온도와 최고 결정성장 온도를 도출하였으며 핵형성 온도는 전이온도와 같은 $490^{\circ}C$로 선정하였다. 결정화 유리를 제조하기 위하여 두 단계의 열처리를 실시하였으며 , 생성된 결정상은 Lithium fluorhectorite와 Lithium boron fluorphlogopite결정상 이었다. 계속적으로 제조된 결정화 유리는 water swelling 현상을 이용하여 분말화를 실시하였으며 평균 입도크기는 2.574 $\mu\textrm{m}$이었다. glass ceramics 분말은 물에 넣으면 반응하여 팽창하는 것과 함께 끈적끈적한 sol이 생성되는 현상을 이용하여 green sheet 제조를 위한 slurry를 제조하였다. Tape casting을 위한 slurry의 결정화 유리 분말 대비 용매의 최적 비율은 100:18이었고, 슬러리의 점도는 11,000~14,000cps 이었다. KCl 1 M용액 10min담지 시편에 대해서는 $900^{\circ}C$에서, 20 min담지 시편에 대해서는 $800^{\circ}C$에서 각각 치밀한 소결성을 나타내었다.

• 한국주조공학회지
• /
• 제37권6호
• /
• pp.186-192
• /
• 2017

The lost foam casting method was used to fabricate Al-Si alloy thin sheet specimens; the effects of chemical composition and process variables on the mold filling and mechanical properties were investigated. The mold filling capability was observed to be proportional to the pouring temperature, and both the vibration imposed during the casting and the application of a pattern coating had rather negative effects. The mold filling capability also decreased with the addition of Mg or TiB. When the Mg content increased, the tensile strength of the cast alloy was enhanced, but the elongation decreased. However, after T6 heat treatment, both the strength and the elongation were improved. TiB addition for grain refining or pattern coating did not significantly affect the tensile properties.

• 한국세라믹학회지
• /
• 제31권6호
• /
• pp.595-600
• /
• 1994

Ni0.3Zn0.7Fe2O4 ferrite specimens were fabricated by dry pressing and tape casting method. The properties of each specimen were measured and compared. In order to design and manufacture the chip devices effectively, one important criterion can be that the sintered density of the laminated body should approach close to that of the dry pressed body which is regarded as standard. This requirement could be satisfied by controlling the solid loading of the ferrite sheet, lamination temperature and pressure. Using the optimum conditions (solid loading 55 wt%, lamination temperature 6$0^{\circ}C$, lamination pressure 400 kg/$\textrm{cm}^2$, sintered at 125$0^{\circ}C$ 2h) a sintered ferrite, with the density of 5.18g/㎤ and permeability of 1390 at 0.5 MHz, were obtained.