• 한국생산제조학회지
• /
• 제6권3호
• /
• pp.111-117
• /
• 1997

The sudden-stop apparatus is made to measure the residual stress of the infinitesimal area at the turning work surface by using the X-ray stress apparatus. This study is trued to make the cutting work the instantaneous stopping state in the normal working state. The behaviour of work material near the tool is estimated. The estimation method is that the distribution of residual stress can be also measured. The object is to clarify and control the mechanism to leave the adequate stress of the finishing surface. It's beginning is due to observe the occurrence state of the residual stress at the cutting work. The result obtained by this study is as follows. The chips are not separated from the work materials at all the cutting experiments of built-up edges or the shearing areas etc. which can be precisely observed by using the sudden-stop apparatus. The strain of movable system which can be seen at the part of working layer means the size of strain. This experiment proves that the working strain should be lessened to make the size of strain control the residual stress happened at the cutting surface.

• Advances in materials Research
• /
• 제5권2호
• /
• pp.107-120
• /
• 2016

The static analysis of the simply supported functionally graded plate under transverse load by using a new sinusoidal shear deformation theory based on the neutral surface concept is investigated analytically in the present paper. No transversal shear correction factors are needed because a correct representation of the transversal shearing strain is given. The mechanical properties of the FGM plate are assumed to vary continuously through the thickness according to a power law formulation except Poisson's ratio, which is kept constant. The equilibrium and stability equations are derived by employing the principle of virtual work. Results are provided for thick to thin plates and for different values of the gradient index k, which subjected to sinusoidal or uniformly distributed lateral loads. The accuracy of the present results is verified by comparing it with finite element solution. From the obtained results, it can be concluded that the proposed theory is accurate and efficient in predicting the displacements and stresses of functionally graded plates.

• Computers and Concrete
• /
• 제17권6호
• /
• pp.723-737
• /
• 2016

In this paper an approach was described for determination of direction of sliding block in rock slopes containing planar non-persistent open joints. For this study, several gypsum blocks containing planar non-persistent open joints with dimensions of $15{\times}15{\times}15cm$ were build. The rock bridges occupy 45, 90 and $135cm^2$ of total shear surface ($225cm^2$), and their configuration in shear plane were different. From each model, two similar blocks were prepared and were subjected to shearing under normal stresses of 3.33 and $7.77kg/cm^{-2}$. Based on the change in the configuration of rock-bridges, a factor called the Effective Joint Coefficient (EJC) was formulated, that is the ratio of the effective joint surface that is in front of the rock-bridge and the total shear surface. In general, the failure pattern is influenced by the EJC while shear strength is closely related to the failure pattern. It is observed that the propagation of wing tensile cracks or shear cracks depends on the EJC and the coalescence of wing cracks or shear cracks dominates the eventual failure pattern and determines the peak shear load of the rock specimens. So the EJC is a key factor to determine the sliding direction in rock slopes containing planar non-persistent open joints.

• 한국지반공학회논문집
• /
• 제23권10호
• /
• pp.57-64
• /
• 2007

현재 불포화토에 대한 많은 연구가 진행되어 왔고 최근 들어 많은 연구자들이 불포화지반의 안정성을 보다 합리적으로 판단하고 해석하기 위해 불포화상태를 고려한 연구의 필요성을 제기하여 왔다. 이를 위해서는 흡인력에 대한 전단강도의 증진효과를 정량화하고 이를 안정해석에 적용하는 것이 요구되고 있는 실정이다. 따라서 본 연구에서는 불포화 사질토의 전단강도 특성을 규명하기 일해서 국내에 널리 분포하는 화강풍화토 7가지를 대상으로 불포화 삼축압축시험을 수행하였으며, 결과치를 분석하여 강도특성을 규명하고자 한다.

• 지질공학
• /
• 제12권1호
• /
• pp.75-88
• /
• 2002

오염된 연약지반에 편재하중이 작용하게 되면 지반 중에 침하, 측방변위, 융기 및 전단파괴 등의 큰 소성 전단변형이 발생하게 되고, 때로는 지반과 구조물에 막대한 손상을 초래하게 된다. 따라서 본 연구는 오염된 연약지반의 식내모형실험을 실시하였으며 측방유동압의 결정방법을 기존의 이론식과 비교하여 분석하였다. 모형실험은 먼저 모형재하장치를 제작하고 토조 안에 오염된 지반시료를 채워 비배수상태에서 하중을 인정한 시간 간격으로 재하하여 변형상태를 관측하였다. 그 결과 편재 하중을 받는 오염된 연약지반에서의 측방유동압은 P=K$_{0}$YH식에 의해서 산정함이 비교적 적절하며, 측방유동압의 최대값은 토층두께(H)의 0.3H 부근에서 발생하였다. 또한 종합형과 Poulos의 분포형태 및 오염되지 않는 연약점토(CL, CH) 지반보다 지표면측으로 상승하여 발생하였다.

• 복식
• /
• 제57권3호
• /
• pp.53-62
• /
• 2007

The purpose of this study was to investigate mechanical and comfort performances of the material for the improved working uniform for a volunteer fire brigade member, to get basic data for its evaluation and to help its material and design development. The results were as follows; The material of the newly developed working uniform was thinner and lighter than the material of the current used working uniform. It had better breathability, air permeability and heat transmission rate than the current one. It also had superior anti-flammability In all mechanical properties(tensile, bending, shearing, compression and surface properties), it showed better performances than the current one. It elongated and bended easier and more in both warp and weft directions. The elastic recovery and shape stability after elongation were also higher. The recovery and resistance to shearing and the resiliency and recovery after compression were also better than the current one. It was more flexible, softer and smoother in primary hand value, and was more suitable for the material for winter suit which needs softness and fullness in total hand value. The material of the improved working uniform showed lower thermal insulation value and higher evaporative resistance value compared to the material of the currently used working uniform from the sweating thermal manikin test. It was shown that the physical performances and the hand value of the textile material used in the newly developed working uniform for a volunteer fiber brigade member was improved compared to the one used in the currently used working uniform.

• 소성∙가공
• /
• 제14권4호
• /
• pp.375-383
• /
• 2005

The shear spinning process, where the plastic deformation zone is localized in a very small portion of the workpiece, shows a promise for increasingly broader application to the production of axially symmetric parts. In this paper, the three components of the working force are calculated by a newly proposed deformation model in which the spinning process is understood as shearing deformation after uniaxial yielding by bending, and shear stress, $\tau_{rz}$, becomes k, yield limit in pure shear, in the deformation zone. The tangential force are first calculated and the feed force and the normal force are obtained by the assumption of uniform distribution of roller pressure on the contact surface. The optimum contact area is obtained by minimizing the bending energy required to get the assumed deformation of the blank. The calculated forces are compared with experimental results. A comparison shows that theoretical prediction is reasonably in good agreement with experimental results

• 대한기계학회논문집
• /
• 제5권2호
• /
• pp.88-93
• /
• 1981

The three force components of shear spinning are calculated by a newly proposed deformation model. The spinning process is understooed as shearing deformation arter uniaxial yuelding by ending, and shear stress .tau.$\sub$rz/ becomes .kappa. the yueld limit in pure shear, in the deformation zone. The tangential forces are calculated and then the feed forces and normal foeces are obtained by assuming a nuiform distribution of roller pressure on the contact surface. An optimum contact area is obtaned by minimizing the bending energy required to obtain the assumed deformation mechanism. The calculated forces are compared with experimental data form published literature and present experiments. Good agreement cetween calculated and experimental values for working forces is obtained over a wide range of process variables.

• 한국정밀공학회지
• /
• 제17권4호
• /
• pp.114-120
• /
• 2000

Burr is an unavoidable and undesirable by-product of most metal cutting or shearing operations. This burr must be removed to improve the fit of machined parts and safety of workers, to improve the effectiveness of finishing operations. Despite the full or partial automation of FMC or FMS, deburring operations to obtain workpiece with fine surface quality are difficult to be automated since the occurrence and condition of burr are not constant. This study focused on developing a software for deburring automation, which includes automatic recognition of parts, generation of deburring tool path and NC code, by analyzing the IGES format file which contains information of part geometry. The successful performance of developed software was demonstrated by computer simulation and deburring experiment using miniature end brush. And, this research can provide a basis for further advanced studies for automated deburring applications.

• Structural Engineering and Mechanics
• /
• 제15권3호
• /
• pp.315-329
• /
• 2003

As shear occurs along a soil-structure interface, a localized zone with a thickness of several grain diameters will develop in soil along the interface, forming an interfacial layer. In this paper, the behaviour of a soil-structure interface is studied numerically by modelling the plane shear of a granular layer bounded by rigid plates. The mechanical behaviour of the granular material is described with a micro-polar hypoplastic continuum model. Numerical results are presented to show the development of shear localization along the interface for shearing under conditions of constant normal pressure and constant volume, respectively. Evolution of the resistance on the surface of the bounding plate is considered with respect to the influences of grain rotation.