• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.500-503
• /
• 2011

Blood flow simulations in an idealized carotid bifurcation model with considering wall compliance were carried out to investigate the effect of wall elasticity on the wall shear stress and wall solid stress. Canonical waveforms of flowrates and pressure in the carotid arteries were imposed for the boundary conditions. Comparing to rigid wall model, generally, we could find an increased recirculation region at the carotid bulb and an overall reduced wall shear stress. Also, there was appreciable change of flowrate and pressure waveform in longitudinal direction. Solid and wall shear stress concentration occurs at the bifurcation apex.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.2
• /
• pp.62-67
• /
• 2013

The influence of internal stress and joint strength(shear, tensile) according to the deposition conditions was investigated by the Polyimide substrate and ZnO thin film. Deposition thickness and temperature affect the internal stress and the internal stress was minimum at the 60nm and $200^{\circ}C$ of the deposition conditions. Tensile strength is large at the deposition condition that shear strength is large and the shear strength was about 50% of the tensile strength. The shear strength and tensile strength were large at deposition condition that internal stress was small. Crack occurred near the joint interface of Polyimide substrate and progressed along the interface until the final fracture.

• Steel and Composite Structures
• /
• v.41 no.6
• /
• pp.851-860
• /
• 2021

In this paper, a new approach of interface stress analysis in steel beam strengthened by porous FGM (Functionally Graded Materials) is presented to calculate the shear stress in the hybrid steel beam and loaded by a uniformly distributed load. The results show that there exists a high concentration of shear stress at the ends of the imperfect FGM, which might result in premature failure of the strengthening scheme at these locations. A parametric study has been conducted to investigate the sensitivity of interface behavior to parameters such as the rigidity of FGM plate (degree of homogeneity), the porosity index of FGM and the thickness of adhesive all were found to have a marked effect on the magnitude of maximum shear stress in the FGM member. we can conclude that the new approach is general in nature and may be applicable to all kinds of materials.

• Journal of the Korean Ceramic Society
• /
• v.49 no.3
• /
• pp.231-235
• /
• 2012

Plasticity is the ability of clay to respond to pressure with a continuous and permanent change of shape in any direction without breaking apart, and hold that shape when released. In this work, the effect of water content and aging period on the plasticity of porcelain clay was evaluated using the capillary rheometer to measure the flow rate and the shear stress. The shear stress of porcelain clay was slightly increased with increasing the aging period, indicating that the plasticity of porcelain clay was influenced by an organic content. It was also observed that the water content in the porcelain clay had a great influence on the plasticity of porcelain clay. The shear stress with water content of 21 wt% was sharply increased with increasing shear rate, but the shear stresses with water contents of 24 and 27 wt% is gently incremented.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.52 no.3
• /
• pp.73-79
• /
• 2010

In the present study, the loading frequency dependencies of cyclic shear strength and elastic shear modulus of reconstituted clay were examined by performing undrained cyclic triaxial tests and undrained cyclic triaxial tests to determine deformation properties. The result of undrained cyclic triaxial test of reconstituted and saturated clay shows that a faster frequency leads to higher stress amplitude ratio, but when the frequency becomes fast up to a certain point, the stress amplitude ratio will reach its maximum limit and the frequency dependence becomes insignificant. And also, the result of undrained cyclic triaxial deformation test shows a fact that a faster loading frequency leads to higher equivalent shear modules and smaller hysteresis damping ratio, and confirms the frequency dependence of cohesive soil. Meanwhile, the result of the creep test shows that continuing creep is created in the undrained cyclic triaxial test with slow loading frequency rate, and since loading rate becomes slower at the vicinity of the maximum and the minimum deviator stress due to sine wave loading, the vicinity of the maximum and the minimum deviator stress shall be more influenced by creep.

• Transactions of Materials Processing
• /
• v.12 no.4
• /
• pp.358-363
• /
• 2003

Adiabatic shear bands have been observed in the serrated chip during high strain rate metal cutting process of medium carbon steel and titanium alloy The recent microscopic observations have shown that dynamic recrystallization occurs in the narrow adiabatic shear bands. However the conventional flow stress models such as the Zerilli-Armstrong model and the Johnson-Cook model, in general, do not predict the occurrence of dynamic recrystallization (DRX) in the shear bands and the thermal softening effects accompanied by DRX. In the present study, a strain hardening and thermal softening model is proposed to predict the adiabatic shear localized chip formation. The finite element analysis (FEA) with this proposed flow stress model shows that the temperature of the shear band during cutting process rises above 0.5Τ$_{m}$. The simulation shows that temperature rises to initiate dynamic recrystallization, dynamic recrystallization lowers the flow stress, and that adiabatic shear localized band and the serrated chip are formed. FEA is also used to predict and compare chip formations of two flow stress models in orthogonal metal cutting with AISI 1045. The predictions of the FEA agreed well with the experimental measurements.s.

• Geotechnical Engineering
• /
• v.2 no.1
• /
• pp.55-66
• /
• 1986

Considering the effects of confining pressure, initial shear stress, cyclic stress ratio and number of loading cycles, cyclic triaxial tests are carried out to clarify the soil dynamic properties such as shear modulus and value of material damping of clay under undrained cyclic loading conditions. The results show that no obvious dependency on initial shear stress and effective confining stress are recognized in the shear modulus and damping ratio plotted versus strain. However, the shear modulus decreases and the damping ratio increases with increasing axial strain. When compared with others, it is also revealed that the shear moduli are distributed within the range curves obtained using empirical equations derived by Marcuson et al. (3) and Kokusho et al. (4), and damping ratios are distributed between the curves obtained by Kokusho et al. (4) and Ishihara et al. (9).

• Korea-Australia Rheology Journal
• /
• v.19 no.1
• /
• pp.43-47
• /
• 2007

The polydiacethylene (PDA) is known to change its color by mechanical shear. The shear-induced color transition has been reported with elastomer or film type of PDA. In this paper, we newly investigated the transition with liposome type of PDAs in polymeric solutions. The liposomes were dispersed in Poly(vinyl alcohol) 2% + Sodium borate 1%, Poly(vinyl alcohol) 15% and Hyaluronic acid 1% (PVA/B, PVA, HA). The shear stress was continuously imposed to each solution by stress control type rheometer with coni-cylinder fixture. The degree of color transition was quantified with the characteristic absorbance peak at 540 nm (blue) and 640 nm (red). As a result, PDA liposome in PVA/B solution changed the color from blue to red upon increasing the magnitude of shear (from 0 to 100 Pa) and the duration of shear-imposed time (from 0 to 5400 sec). Meanwhile, PDA liposome in HA or PVA solution did not noticeably change the color, even though the low shear viscosities of the solutions were kept almost constant. This color transition of PDA liposome is expected to measure the magnitude of shear, and to distinguish different responses of polymeric solutions to the applied shear.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.35 no.9
• /
• pp.191-198
• /
• 2019

All over the Republic of Korea, there are many masonry buildings which have been built since 1970s. When the earthquake at Po-Hang occurred, this is the main cause of huge damage because the masonry buildings have not seismic capacity. When masonry buildings are failed, two type of the failure modes can be shown, which are in-plane mode and out-plane mode. In-plane mode can have seismic capacity in masonry so diagonal shear test is performed in this study. The purpose of this study was to find the best way to reinforce the materials through the diagonal shear test. Through the test, shear stress and shear modulus of elasticity will be calculated, referred to the ASTM E 519-02. The variables in this test are ${\phi}3$ wire, three types of wire meshes, polypropylene strap and different types of brick. Each variable is applied to the same condition of the $1.2m{\times}1.2m$ masonry walls which are made by ASTM E 519-02. Compared to each variable with shear stress and shear modulus of elasticity, the best way of reinforcing method to have seismic capacity will be proved in this study.

• Geomechanics and Engineering
• /
• v.25 no.3
• /
• pp.245-251
• /
• 2021

The present study investigated the ageing effect on compressibility, permeability and shear strength behavior of kaolin and bentonite samples in the presence of NaCl and CaCl₂ solutions. The compressibility, permeability and shear strength parameters were determined on the 60, 190, and 250 days cured samples. The results have shown that, the kaolin sample becomes more compressible in the presence Ca²⁺ ions with ageing. Generally, the normalized compression index values of bentonite samples increased at the end of 60 days and 250 days curing time periods. The normalized permeability value of kaolin decreased by ageing in the presence of Na⁺ ions almost twofold. The permeability values of bentonite increased both in NaCl and CaCl₂ solutions during ageing. In the presence of Na⁺ ions kaolin had higher max. shear stress value than Ca²⁺ ions. When the max. shear stress values of 0, 60 and 190 days samples were compared, it was seen that NaCl solution had no significant effect on the shear strength of kaolin sample. However, the shear strength of kaolin increased in the CaCl₂ solution during ageing. In the presence of Ca²⁺ ions the max. shear stress value of bentonite was higher. The results of this study have shown that ageing has significant effects on the compressibility, permeability and shear strength of kaolinitic and bentonitic clayey soils.