• 대한기계학회논문집A
• /
• 제40권6호
• /
• pp.565-571
• /
• 2016

본 논문은 Alloy 617 모재와 용접재에 대한 저사이클 피로 시험 후의 파괴 시험편에 대한 거시적 및 미시적 파면해석을 나타낸다. 용접재 시험편은 Alloy 617의 가스텅그스텐아크 용접 패드로부터 채취, 제작하였다. 본 연구의 목적은 Alloy 617의 모재와 용접재 시험편의 저사이클 파괴 모드 및 기구의 거시적 및 미시적 양상을 고찰하는 것이다. 전변형률 제어 피로시험이 상온에서 0.6, 0.9, 1.2 및 1.5%에 대하여 수행되었다. Alloy 617 모재의 거시적 파면은 피로하중 축에 수직인 평평한 형태의 양상을 보였으나, 용접재 시험편의 경우는 상대적으로 전단/별모양의 양상의 파괴를 나타내었다. 두 시험편 모두 피로균열전파 영역에서는 명확한 스트라이에이션이 관찰되었다. 한편, 모재의 피로균열은 피로 하중 축에 수직인 방향으로 결정입내를 따라 전파하였으나, 용접재 시험편의 경우 하중 축에 거의 $45^{\circ}$의 경사진 형태의 결정입내로 나타났다.

• 대한치과교정학회지
• /
• 제40권5호
• /
• pp.342-348
• /
• 2010

본 연구는 미백, 탈감작제 도포 후, 셀프 에칭 프라이머를 이용하여 브라켓 접착 시 법랑질에 대한 전단결합강도를 비교하기 위해 시행되었다. 48개의 소구치를 무작위로 12개씩 4개의 그룹으로 분류하였다. Group 1: 15% hydrogen-peroxide office bleaching agent (Illumine Office-IO), Group 2: IO + BisBlock Oxalate Dentin-Desensitizer, Group 3: Bis-Block Oxalate Dentin-Desensitizer, Group 4: 아무것도 하지 않음(대조군). 브라켓 접착 24시간 후 전단결합강도를 측정하였으며, 만능시험기의 속도를 5 mm/min로 하여 브라켓이 탈락할 때까지 시행하였다. Modified adhesive remnant index를 이용하여 탈락 양상을 분석하였다. 미백만 시행, 미백과 탈감작제 도포, 탈감작제만 도포한 경우 모두 브라켓의 전단결합강도를 현저히 감소시켰으며 ($p$ = 0.001), 이 세 실험군 간에는 통계적으로 유의성 있는 차이를 관찰할 수 없었다 (Group 1-Group 2, $p$ = 0.564; Group 1-Group 3, $p$ = 0.371; Group 2-Group 3, $p$ = 0.133). 세 실험군에서 브라켓의 탈락은 주로 법랑질-접착제 계면에서 발생하여 브라켓 베이스에 접착제의 100%가 남아있었다. 따라서 미백과 탈감작제 도포는 교정치료 후에 시행하는 것이 바람직하다.

• 한국농공학회지
• /
• 제37권3_4호
• /
• pp.61-71
• /
• 1995

Natural ground is a composite consisted of the three phases of water, air and soil paircies. Among the three components, water as a material is weU understood but soil particles are not in foundation engineering. Especially, weathered granite soil generally shows a large volumetric expansion when they freeze. And, the stability and durability of the soil have shown decreased with repetitive freezing and thawing processes. These unique charcteristics may cause various construction and management problems if the soil is used as a construction material and foundation layers. This project was initiated to investigate the soil's physical and engineering characteristics resulting from freezing and freezing-thawing processes. Research results may be used as a basic data in solving various problems related to the soil's unique characteristics. The following conclusions were obtained: The degree of decomposition of weathered granite soil in Kangwon-do was very different between the West and East sides of the divide of the Dae-Kwan Ryung. Soil particles distributed wide from very coarse to fine particles. Consistency could be predicted with a function of P200 as LL=0.8 P200+20. Permeability ranged from 10-2 to 10-4cm/sec, moisture content from 15 to 20% and maximum dry density from 1.55 to 1.73 g /cmΥ$^3$ By compaction, soil particles easily crushed, D50 of soil particles decreased and specific surface significantly increased. Shear characteristics varied wide depending on the disturbance of soil. Strain characteristics influenced the soil's dynamic behviour. Elastic failure mode was observed if strain was less than 1O-4/s and plastic failure mode was observed if strain was more than 10-2/s. The elastic wave velocity in the soil rapidly increased if dry density became larger than 1.5 g /cm$^3$ and these values were Vp=250, Vg= 150, respectively. Frost heave ratio was the highest around 0 $^{\circ}C$ and the maximum frost heave pressure was observed when deformation ratio was less than 10% which was the stability state of soil freezing. The state had no relation with frost depth. Over freezing process was observed when drainage or suction freezing process was undergone. Drainage freezing process was observed if freezing velocity was high under confined pressure and suction frost process was occurred if the velocity was low under the same confined process.

• Geomechanics and Engineering
• /
• 제35권2호
• /
• pp.195-208
• /
• 2023

The nodular diaphragm wall (NDW) is a novel type of foundation with favorable engineering characteristics, which has already been utilized in high-rise buildings and high-speed railways. Compared to traditional diaphragm walls, the NDW offers significantly improved vertical bearing capacity due to the presence of nodular parts while reducing construction time and excavation work. Despite its potential, research on the vertical bearing characteristics of NDW requires further study, and the investigation and visualization of its displacement pattern and failure mode are scant. Meanwhile, the measurement of the force component acting on the nodular parts remains challenging. In this paper, the vertical bearing characteristics of NDW are studied in detail through the indoor model test, and the displacement and failure mode of the foundation is analyzed using particle image velocimetry (PIV) technology. The principles and methods for monitoring the force acting on the nodular parts are described in detail. The research results show that the nodular part plays an essential role in the bearing capacity of the NDW, and its maximum load-bearing ratio can reach 30.92%. The existence of the bottom nodular part contributes more to the bearing capacity of the foundation compared to the middle nodular part, and the use of both middle and bottom nodular parts increases the bearing capacity of the foundation by about 9~12% compared to a single nodular part of the NDW. The increase in the number of nodular parts cannot produce a simple superposition effect on the resistance born by the nodular parts since the nodular parts have an insignificant influence on the exertion and distribution of the skin friction of NDW. The existence of the nodular part changes the displacement field of the soil around NDW and increases the displacement influence range of the foundation to a certain extent. For NDWs with three different nodal arrangements, the failure modes of the foundations appear to be local shear failures. Overall, this study provides valuable insights into the performance and behavior of NDWs, which will aid in their effective utilization and further research in the field.

• 한국강구조학회 논문집
• /
• 제10권3호통권36호
• /
• pp.451-461
• /
• 1998

1차전단변형 판이론에 의한 비등방성 복합적층판의 임계좌굴하중 및 좌굴모드는 기존의 해석적인 방법으로는 다양한 조건에 대하여 해를 제공할 수 없다는 단점을 가지고 있다. 따라서 근사해법인 수치해석을 이용하게 되는데, 이러한 수치해석기법으로 기존 상용프로그램에서는 유한요소법이 널리 사용되었다. 그러나 least upper bound 특성을 가지고 있는 유한요소법을 이용한 적층판의 좌굴해는 구조적인 안정성을 보장하지 못하는 경우도 있다. 따라서 본 논문에서는 유한차분법에 의한 좌굴해석을 수행하여 유한요소법과 상호 비교함으로서 각 경우에 관한 두 가지 수치해석기법의 장단점을 규명하고 효과적으로 적용할 수 있는 기법을 제시하는 것을 목적으로 하였다. 수치해석 결과, 유한차분법에 의한 좌굴하중 및 좌굴모드는 신소재를 사용하는 적층 구조물의 실용화에 앞서 다양한 기준을 제시할 수 있을 것으로 판단된다.

• 고무기술
• /
• 제9권1호
• /
• pp.1-12
• /
• 2008

Effects of silane modifier, bis(triethoxysilylpropyl) tetrasulfide (TESPT(S4)) and bis(triethoxysilylpropyl) disulfide (TESPD(S2)), on silica filled compound were investigated upon processability, dynamic, mechanical, heat build-up, blowout properties, and silica dispersion in natural rubber (NR). The temperature of the S2 treated silica compound generated higher than that of the S4 treated compound during internal mixer compounding. The shear viscosity of the S2 compound exhibited lower than that of the S4 compound and the viscosity measured in dynamic mode was close to each other. The elongation modulus of the S2 compound exhibited lower than that of the S4; however, the tear resistance strength of the S2 compound exhibited higher than that of the S4 compound. The loss tan$\delta$ values of the S2 compound exhibited higher than those of the S4 at room temperature. The augmentation of the test temperature lowered the tan$\delta$ values of each compound, which results in close tan$\delta$ values to each other at $100^{\circ}C$. The S2 compound deformed less than the S4 compound, and the blowout time of each compound was close to each other. The S2 compound generated more heat build-up than the S4 compound. The abrasion loss of the S2 compound was less than that of the S4 compound. The size of the silica agglomerate reduced on both S4 and S2 compounds upon vulcanization. The addition of the bifunctional silanes (S2 and S4) on silica filled NR compound improved the processability of each compound and their effects were more significant on the S2 compound than the S4 compound. After vulcanization the silica agglomerate size of each compound reduced compared with before vulcanization.

• Structural Engineering and Mechanics
• /
• 제14권3호
• /
• pp.287-306
• /
• 2002

The assessment of structural performance of transfer structures under potential seismic actions is presented. Various seismic assessment methodologies are used, with particular emphasis on the accurate modelling of the higher mode effects and the potential development of a soft storey effect in the mega-columns below the transfer plate (TP) level. Those methods include response spectrum analysis (RSA), manual calculation, pushover analysis (POA) and equivalent static load analysis (ESA). The capabilities and limitations of each method are highlighted. The paper aims, firstly, to determine the appropriate seismic assessment methodology for transfer structures using these different approaches, all of which can be undertaken with the resources generally available in a design office. Secondly, the paper highlights and discusses factors influencing the response behaviour of transfer structures, and finally provides a general indication of their seismic vulnerability. The representative Hong Kong building considered in this paper utilises a structural system with coupled shear walls and moment resisting portal-frames, above and below the TP, respectively. By adopting the wind load profile stipulated in the Code of Practice on Wind Effects: Hong Kong-1983, all the structural members are sized and detailed according to the British Standards BS8110 and the current local practices. The seismic displacement demand for the structure, when built on either rock or deep soil sites, was determined in a companion paper. The lateral load-displacement characteristic of the building, determined herein from manual calculation, has indicated that the poor ductility (brittle nature) of the mega-columns, due mainly to the high level of axial pre-compression as found from the analysis, cannot be effectively alleviated solely by increasing the quantity of confinement stirrups. The interstorey drift demands at lower and upper zones caused by seismic actions are found to be substantially higher than those arising from wind loads. The mega-columns supporting the TP and the coupling beams at higher zones are identified to be the most vulnerable components under seismic actions.

• 한국구조물진단유지관리공학회 논문집
• /
• 제9권2호
• /
• pp.181-190
• /
• 2005

본 연구에서는 탄소섬유메쉬(Carbon Fiber Mesh, CFM)를 이용한 철근콘크리트 보의 휨보강 효과를 연구하며 CFM의 정착과 겹침이음방법에 따른 영향을 연구하고자 한다. 휨이 지배적인 5개의 철근 콘크리트 실험체를 제작하고 CFM으로 보강한 후 단순지지형태로 가력을 하여 그 보강효과를 규명하고자 한다. 보의 전체 길이는 2400mm이며 깊이와 폭이 모두 300mm로서 휨이 지배될 수 있도록 실험체를 계획하였다. 실험으로부터, 균열이 시작되는 단계에서 CFM의 보강효과는 미약한 것으로 나타났으나, 균열발생 이후에는 보의 휨강성확보의 측면에서 효과가 있는 것으로 나타났다. 보강된 실험체와 보강되지 않은 실험체의 비교를 통하여 CFM보강효과를 확인할 수 있었으며, 균열발생시와 항복시에 대하여 보강효과를 반영하여 예측한 계산값과 실험결과가 좋은 일치를 보이는 것으로 나타났다.

• 한국전산구조공학회논문집
• /
• 제14권4호
• /
• pp.481-494
• /
• 2001

본 논문은 철근 콘크리트 구조물의 비탄성 해석을 수행하기 위하여 개발된 9절점 퇴화 쉘 요소에 대하여 기술하였다. 개발된 쉘 유한요소는 퇴화고체기법과 함께 구조물에서 발생하는 횡 전단 변형효과를 고려하기 위하여 Reissner-Mindlin (RM)가정을 도입하였다. RM가정을 바탕으로 한 퇴화 쉘 요소는 쉘의 두께가 얇거나, 즉 종횡비가 작거나, 균일하지 않은 유한요소망을 사용할 경우 구조물의 강성이 과대하게 계산되는 강성과대현상(Locking phenomenon)이 나타나게 된다. 강성과대현상은 선택적 감차 적분, 비 적합 모드, 가변형도 등을 사용하여 개선하는데 특히 가변형도법에 바탕을 둔 대체변형도는 많은 유한요소에 성공적으로 적용되어 왔다. 그러나 이와는 대조적으로 콘크리트의 비탄성 해석에 가변형도법을 도입하고 그 성능을 조사한 사례는 매우 적다. 따라서 본 연구에서는 가변형도법과 미시적 재료모델을 바탕으로 RM 쉘 요소를 정식화하고 미를 유한요소프로그램으로 개발하였다. 개발된 철근 콘크리트 쉘 요소의 성능은 수치예제를 통하여 검증하였다. 수치예제로부터 개발된 쉘요소를 이용하여 구해진 해석결과가 실험결과 또는 다른 해석결과에 근접함을 알 수 있다.

• Structural Engineering and Mechanics
• /
• 제75권3호
• /
• pp.401-414
• /
• 2020

Unlike the existing truss models for shear and torsion analysis, in this study, the torsional capacities of reinforced concrete (RC) members were estimated by introducing multi-potential capacity criteria that considered the aggregate interlock, concrete crushing, and spalling of concrete cover. The smeared truss model based on the fixed-angle theory was utilized to obtain the torsional behavior of reinforced concrete member, and the multi-potential capacity criteria were then applied to draw the capacity of the member. In addition, to avoid any iterative calculation in the existing torsional behavior model, a simple strength model was suggested that considers key variables, such as the effective thickness of torsional member, principal stress angle, and strain effect that reduces the resistance of concrete due to large longitudinal tensile strain. The proposed multi-potential capacity concept and the simple strength model were verified by comparing with test results collected from the literature. The study found that the multi-potential capacity could estimate in a rational manner not only the torsional strength but also the failure mode of RC members subjected to torsional moment, by reflecting the reinforcing index in both transverse and longitudinal directions, as well as the sectional and material properties of RC members.