• 대한조선학회논문집
• /
• 제47권3호
• /
• pp.306-320
• /
• 2010

Modern ultra-large container carriers can be exposed to the unprecedented springing excitation from ocean waves due to their relatively low torsional rigidity. Large deck opening on the deck of container carriers tends to cause warping distortion of hull structure under wave-induced excitation, eventually leading to the higher chance of resonance vibration between its torsional response and incoming waves. To handle this problem, a higher-order B-spline Rankine panel method and Vlasov-beam FE model was directly coupled in the time domain, and the coupled equation was solved by using an implicit iterative method. In order to capture the complicated behavior of thin-walled open section girder, a sophisticated beam-based finite element model was developed, which takes into account warping distortion and shear-on-wall effect. Then, the developed beam model was directly coupled with the time-domain Rankine panel method for hydrodynamic problem by using the fixed-point iteration method. The developed computational scheme was validated through the comparison with the frequency-domain solution on the container carrier model in linear springing regime.

• Composites Research
• /
• 제15권3호
• /
• pp.18-29
• /
• 2002

본 논문에서는 얇은 벽보로 모델링 한 위성체 구조물에 입사되는 열 하중에 의해 발생하는 굽힘 진동과 열적 플러터에 대하여 연구하였다. 복합재료 얇은 벽보는 회전관성과 1차, 2차 와핑, 전단변형의 비고전적 요소를 포함한다. CUS구조물로 모델링한 복합재료 얇은 벽보의 열 진동 특성은 적층 순서와 섬유강화복합재료의 방향특성인자로부터 기인된 종방향 굽힘과 횡방향 굽힘의 언성과 관련하여 연구되었다. 수치 해석적인 방법으로 열적 플러터의 안정성 영역의경계값을 구하였으며, 태양 열 플럭스의 입사각, 감쇠계수, 섬유각의 변화에 의한 보의 변위를 구하였다. 주 구조물에 압전소자를 부착하여, 감지기와 작동기로 사용하여 제어해석을 수행하였다.

• 대한기계학회논문집B
• /
• 제25권6호
• /
• pp.751-757
• /
• 2001

An experimental study of impinging jet-flow structure has been carried out for a fully developed single circular jet impingement cooling on a flat plate, and the effect of the wall thickness at nozzle exit edge is investigated. Impinging jet flow structures have been measured by Laser-Doppler Velocimeter to interpret the heat transfer results presented previously by Yoon et al.(sup)(10) The peaks of heat transfer rate are observed near the nozzle edge owing to the radial acceleration of jet flow when the nozzle locates close to the impingement plate. The growth of the velocity fluctuations in the wall jet flow is induced by the vortices which originate in the jet shear layer, and consequently the radial distribution of local Nusselt numbers has a secondary peak at the certain radial position. As a wall of circular pipe nozzle becomes thicker for small nozzle-to-target distance, the entrainment can be inhibited, consequently, the acceleration of wall jet flow is reduced and the heat transfer rate decreases.

• Advances in materials Research
• /
• 제1권4호
• /
• pp.245-268
• /
• 2012

Results of isothermal torsional oscillation tests are reported on melts of linear low density polyethylene and isotactic polypropylene. Prior to rheological tests, specimens were annealed at various temperatures ranging from $T_a$ = 180 to $310^{\circ}C$ for various amounts of time (from 30 to 120 min). Thermal treatment induced degradation of the melts and caused pronounced decreases in their molecular weights. With reference to the concept of transient networks, constitutive equations are developed for the viscoelastic response of polymer melts. A melt is treated as an equivalent network of strands bridged by junctions (entanglements and physical cross-links). The time-dependent response of the network is modelled as separation of active strands from and merging of dangling strands with temporary nodes. The stress-strain relations involve three adjustable parameters (the instantaneous shear modulus, the average activation energy for detachment of active strands, and the standard deviation of activation energies) that are determined by matching the dependencies of storage and loss moduli on frequency of oscillations. Good agreement is demonstrated between the experimental data and the results of numerical simulation. The study focuses on the effect of molecular weight of polymer melts on the material constants in the constitutive equations.

• 대한조선학회논문집
• /
• 제55권2호
• /
• pp.161-168
• /
• 2018

This paper presents the design procedure of the suction bucket used to support a subsea manifold. The soil-suction bucket interaction numerical analysis technique was verified by comparing the present results with a reference data. In order to simulate the soil-bucket interaction analyses of a subsea manifold structure, various material data such as undrained shear strength, elastic modulus, and poisson ratio of soft clay in Gulf of Mexico were collected from reference survey. We proposed vertical and horizontal design loads based on system weights and current-induced drag forces. Under the assumption that diameter of the suction bucket was 3.0 m considering real dimension of the subsea manifold frame structures, aspect ratio was decided to be 3.0 based on reference survey. The ultimate bearing load components were determined using tangent intersection method. It was proved that the two design load components were less than ultimate bearing loads.

• 폴리머
• /
• 제27권1호
• /
• pp.75-83
• /
• 2003

다이시아네이트-점토 나노복합재료(dicyantate-clay nanocomposite)를 개질제의 종류와 cation exchange capacity (CEC)의 차이에 따라 용융 in-situ법에 의하여 제조하였고 이들의 물성과 분산을 측정하였다. 다양한 층간 삽입물을 함유하여 다양한 층간거리와 적층밀도를 갖는 montmorillonite (MMT)에 따라 다양한 구조의 나노복합재가 제조되었다. 사용된 다이시아네이트와 점토는 각각의 친화성에 따라 실리케이트 내부로의 삽입정도가 달라졌다. 다이시아네이트-점토 나노복합재료의 분산은 CEC와 개질제의 지방족 사슬길이에 의존하였으며 더 낮은 CEC를 가지고 지방족 사슬의 길이가 짧은 것이 좀 더 분산된 구조를 가지는 것으로 측정되었다. 또한 사용된 개질제에 고분자와의 반응성이 부여되면 층간 삽입이 더욱 용이한 것으로 나타났다. 다이시아네이트 나노복합재료의 전단탄성율은 반응성을 가지며 박리된 구조를 가지는 경우에 더 향상된 물성을 가지는 것으로 나타났다.

• Earthquakes and Structures
• /
• 제10권1호
• /
• pp.239-260
• /
• 2016

Tuned mass dampers (TMDs) have been frequently proposed to mitigate the detrimental effects of dynamic loadings in structural systems. The effectiveness of this protection strategy has been demonstrated for wind-induced vibrations and, to some extent, for seismic loadings. Within this framework, recent numerical studies have shown that beneficial effects can be achieved by placing a linear TMD on the roof of linear elastic structural systems subjected to pulse-like ground motions. Motivated by these positive outcomes, closed-form design formulations have been also proposed to optimize the device's parameters. For structural systems that undergo a near-fault pulse-like ground motion, however, it is unlikely that their dynamic response be linear elastic. Hence, it is very important to understand whether such strategy is effective for inelastic structural systems. In order to provide new useful insights about this issue, the paper presents statistical results obtained from a numerical study conducted for three shear-type hysteretic (softening-type) systems having 4, 8 and 16 stories equipped with a linear elastic TMD. The effectiveness of two design procedures is discussed by examining the performances of the protected systems subjected to 124 natural pulse-like earthquakes.

• Structural Engineering and Mechanics
• /
• 제84권6호
• /
• pp.799-811
• /
• 2022

Adhesive bonding has seen rapid development in recent years, with emphasis to composite patch repairing processes of geometric defects in aeronautical structures. However, its use is still limited given its low resistance to climatic conditions and requirement of specialized labor to avoid fabrication induced defects, such as air bubbles, cracks, and cavities. This work aims to numerically analyze, by the finite element method, the failure behavior of a damaged plate, in the form of a bonding defect, and repaired by an adhesively bonded composite patch. The position and size of the defect were studied. The results of the numerical analysis clearly showed that the position of the defect in the adhesive layer has a large effect on the value of J-Integral. The reduction in the value of J-Integral is also related to the composite stacking sequence which, according to the mechanical properties of the ply, provides better load transfer from the plate to the repair piece through the adhesive. In addition, the increase in the applied load significantly affects the value of the J-Integral at the crack tip in the presence of a bonding defect, even for small dimensions, by reducing the load transfer.

• Tribology and Lubricants
• /
• 제39권3호
• /
• pp.102-110
• /
• 2023

This study aims to quantify the variation in the performance of a tilting pad journal bearing (TPJB) owing to the elastic deformation of its pad. To this end, we first defined a parameter, "elastic preload", and predicted the changes in the performance of the TPJB, as a function of the preload amount. We used the iso-viscosity Reynolds equation, which ignores the temperature rise due to viscous shear in thin films, and the resultant thermal deformation of the bearing structure. We employed a three-dimensional finite element model to predict the elastic deformation of the bearing pad, and a transient analysis, to converge to a static equilibrium condition of the flexible pads and journal. Conducting a modal coordinate transformation helped us avoid heavy computational issues arising from a mesh refinement in the three-dimensional finite element pad model. Moreover, we adopted the Hertzian contact model to predict the elastic deformation at the pivot location. With the aforementioned overall strategy, we predicted the performance changes owing to the elastic deformation of the pad under varying load conditions. From the results, we observed an increase in the preload due to the pad elastic deformation.

• 대한토목학회논문집
• /
• 제34권2호
• /
• pp.505-513
• /
• 2014

본 논문은 암반지층에서 다양한 암반종류 및 절리조건들을 고려하면서 굴착벽체에 작용하는 토압에 대한 절리의 영향을 조사한 것이다. 이를 위해 본 연구는 먼저 기존 선행연구에 대해서 살펴보고 그 다음으로 기존 선행연구의 한계를 극복하기 위하여 개별요소법에 근거한 수치해석적 매개변수해석을 수행하였다. 수치해석은 매개변수로서 암반종류 및 절리조건(절리면의 전단강도, 절리경사각 및 절리군의 수)을 고려하였으며, 지반과 굴착벽체의 상호작용하에 발생된 토압의 크기 및 분포특성이 조사되었다. 이와 더불어, 암반지층에서 발생된 토압과 토사지반에서의 경험토압인 Peck토압이 서로 비교되었다. 비교결과 절리가 형성된 암반지층에서 발생된 토압은 암반의 종류 및 절리조건에 따라서 크게 영향을 받았으며 토사지반에 대한 Peck의 경험토압과 서로 다른 결과를 나타내었다.