• Journal of the Korean Society for Marine Environment & Energy
• /
• v.12 no.4
• /
• pp.273-278
• /
• 2009

Overtopping Wave Energy Convertor (OWEC) is an offshore wave energy convertor for collecting the overtopping waves and converting the water pressure head into electric power through the hydro turbines installed in the vertical duct which is fixed in the sea bed. The numerical wave tank based on the commercial computational fluid dynamics code Fluent is established for the corresponding analysis. Several incident wave conditions and shape parameters of the overtopping device are calculated. The straight line type and parabolic type of the sloping arm are compared in the optimal designing investigation of the overtopping characteristics and discharge for OWEC device. The numerical results demonstrate that the parabolic sloping arm is available for wave running up and the overtopping discharge increasing.

• Korean Journal of Computational Design and Engineering
• /
• v.21 no.4
• /
• pp.389-396
• /
• 2016

The necessity for environment-friendly material development has emerged in the recent automotive field due to stricter regulations on fuel economy and environmental concerns. Accordingly, the automotive industry is paying attention to carbon fiber reinforced plastic (CFRP) material with high strength and stiffness properties while the lightweight. In this study, we determine a shape of lower control arm (LCA) for maximizing the strength and stiffness by optimizing the thickness of each layer when the stacking angle is fixed due to the CFRP manufacturing problems. Composite materials are laminated in the order of $0^{\circ}$, $90^{\circ}$, $45^{\circ}$, and $-45^{\circ}$ with a symmetrical structure. For the approximate optimal design, we apply a sequential two-point diagonal quadratic approximate optimization (STDQAO) and use a process integrated design optimization (PIDO) code for this purpose. Based on the physical properties calculated within a predetermined range of laminate thickness, we perform the FEM analysis and verify whether it satisfies the load and stiffness conditions or not. These processes are repeated for successive improved objective function. Optimized CFRP LCA has the equivalent stiffness and strength with light weight structure when compared to conventional aluminum design.

• KIISE Transactions on Computing Practices
• /
• v.24 no.2
• /
• pp.88-92
• /
• 2018

'UFO2MF' and 'Korean MetaFont Generator' have been developed to convert UFO codes to the corresponding Metafont codes by using outline editing methods. However, 'UFO2MF' cannot express smooth curves because it use only reference points without using control points. And 'Korean MetaFont Generator' can easily design the curve of characters, and supports Hangul characters, but this system does not support Roman characters. In this paper, we propose a UFO2xMF system, which can convert both Korean and Roman characters from outline text information into Metafont codes. UFO2xMF can apply attribute values which can change the shape of letters during the conversion of Metafont code. It is also a highly compatible system that can convert the characters of various languages not only Korean characters but also Roman and other characters into Metafont codes by applying letters with baseline and centerline of gravity.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.572-579
• /
• 2001

Recent industrial requirements for highly precise shape processing have brought the electric discharge machining (EDM) in great need. High precision in EDM is primarily achieved by high performance controllers. However there exists inherent precision loss due to structural deformation. On this background, we study structural deformation characteristics of wire cut EDM via finite element (FE) analysis and axiomatic design. Two different wire cut EDMs are selected as analysis models. 3D CAD package I-Deas is first used to construct FE models of wire cut EDMs, and then ABAQUS FE code is used for following structural analysis. Pertinency of FE mesh refinement is discussed in terms of ${\eta}-factor$. It is shown that performance accuracy of EDM depends strongly on the structural characteristics. Some design enhancements are suggested in an axiomatic design point of view. Finally we provide weight and temperature induced displacement discrepancies between wire end points as position functions of each subframe.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.5
• /
• pp.742-749
• /
• 2003

Failure of a pipeline due to local wall thinning is getting more attention in the nuclear power plant industry. Although guidelines such as ANSI/ASME B31G and ASME Code Case N597 are still useful fer assessing the integrity of a wall thinned pipeline, there are some limitations in these guidelines. For instance, these guidelines consider only pressure loading and thus neglect bending loading. However, most Pipelines in nuclear power plants are subjected to internal pressure and bending moment due to dead-weight loads and seismic loads. Therefore, an assessment procedure for locally wall thinned pipeline subjected to combined loading is needed. In this paper, three-dimensional finite element(FE) analyses were performed to simulate full-scale pipe tests conducted for various shapes of wall thinned area under internal pressure and bending moment. Maximum moments based on true ultimate stress(${\alpha}$$\sub$u,t/) were obtained from FE results to predict the failure of the pipe. These results were compared with test results, which showed good agreement. Additional finite element analyses were performed to investigate the effect of key parameters, such as wall thinned depth, wall thinned angle and wall thinned length, on maximum moment. Also, the effect of internal pressure on maximum moment was investigated. Change of internal pressure did not show significant effect on the maximum moment.

• Journal of Energy Engineering
• /
• v.12 no.4
• /
• pp.320-327
• /
• 2003

A CFD (Computational fluid Dynamics) research is conducted for the investigation of the fuel alteration of MBTU (medium-Btu) gas in IGCC gas turbine combustor. The computational analysis method of the gas turbine combustor is constructed by incorporating MBTU gas reaction and fuel NOx models into commercial CFD code. With the use of the present analysis method, comparisons are made on the flow velocity, the chemical species and the temperature distributions, and on the flame shape and behavior of gas turbine combustor firing natural gas and MBTU gases (coal gas, heavy residue oil gas). Furthermore, the NOx formation characteristics and the turbine matching condition of the combustor are analyzed. Based on the computed analysis results, the present study provides the directions for the redesign and the design modification of IGCC gas turbine combustor firing MBTU gas as alternative fuel.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.8
• /
• pp.891-898
• /
• 2005

Inertia welding is a solid-state welding process in which butt welds in materials are made in bar and in ring form at the joint race, and energy required lot welding is obtained from a rotating flywheel. The stored energy is converted to frictional heat at the interface under axial load. The quality of the welded joint depends on many parameters, including axial force, initial revolution speed and energy amount of upset. working time, and residual stresses in the joint. Inertia welding was conducted to make the large exhaust valve spindle for low speed marine diesel engine. superalloy Nimonic 80A for valve head of 540mm and high alloy SNCrW for valve stem of 115mm. Due to different material characteristics such as, thermal conductivity and flow stress. on the two sides of the weld interface, modeling is crucial in determining the optimal weld geometry and Parameters. FE simulation was performed by the commercial code DEFORM-2D. A good agreement between the Predicted and actual welded shape is observed. It is expected that modeling will significantly reduce the number of experimental trials needed to determine the weld parameters. especially for welds for which are very expensive materials or large shaft. Many kinds of tests, including macro and microstructure observation, chemical composition tensile , hardness and fatigue test , are conducted to evaluate the qualify of welded joints. Based on the results of the tests it can be concluded that the inertia welding joints of the superalloy exhaust valve spindle are better properties than the material specification of SNCrW.

• The Bulletin of The Korean Astronomical Society
• /
• v.41 no.2
• /
• pp.49.2-49.2
• /
• 2016

The number of discovery of asteroids with peculiar rotational states has recently increased, and hence a novel approach for lightcurve analysis is considered to be critical. In order to investigate objects such as Non-Principal Axis (NPA) rotator, we selected a NPA candidate, (5247) Kryolv as our target considering its Principal Axis Rotation (PAR) code and the visibility in early 2016. The observations of Krylov were made using Korea Microlensing Telescope Network (KMTNet) 1.6 m telescopes installed at the three southern sites with TO (Target of Opportunity) observation mode. We conducted R-band time-series photometry over a total of 51 nights from January to April 2016 with several exposures during each allocated run. The ensemble normalization photometry was employed using the AAVSO Photomtric All-Sky Survey (APASS) catalog for the standardization. We successfully confirmed its NPA spin state based on the deviation from the reduced lightcurve, and thus Krylov is recorded as the first NPA rotator of its kind in the main-belt, with its precession and rotation periods, $P{\varphi}=81.18h$ and $P_{\Psi}=67.17h$, respectively. In this paper, we present the spin direction, the 3D shape model and taxonomy of the newly confirmed NPA asteroid (5247) Krylov.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.5
• /
• pp.99-105
• /
• 2012

With the rapid development and diffusion of smart phone applications, mobile users are able to use various useful mobile services in humdrum life. Especially, interesting applications like QR code using camera module in a smart phone are developed continuously nowadays. We realized that the size and shape of shooting objects taken by a smart phone camera module are very different according to their types and versions of the android-based smart phone in the process of developing applications for measuring the shooting object using camera module of a smart phone. In this paper, we investigate the major differences among smart phone types and system versions when we take specific object with camera module of smart phones, analyze the various characteristics of camera modules that influencing the real size of the shooting object taken by a smart phone, and apply them to the development of the smart camruler application.

• Archives of design research
• /
• v.17 no.4
• /
• pp.401-404
• /
• 2004

The proposal defines a Do It Yourself system that radically changes the traditional concept of window. it is based on a D.I.Y. system that allows the users to fully customize its windows according to his needs, combining a wood frame with different elements. At the same time, it is preserving the basic function of light and ventilation and defining a new aesthetic code. Despite the restriction of size and shape, the user can choose among many different elements to increase the space efficiency he needs and to give a more enjoyable perspective to the window both in and out door. Also, All the elements are standard and they can be mass-produced according to specific market needs. Therefore, the window of the future will not be just a thin membrane in between the inside and the outside, but it will also play an important "identification role. According to each individual pick, these new windows will help to give identify to anonymous metropolitan areas and to the people living within them.