• 대한기계학회논문집
• /
• 제12권3호
• /
• pp.590-598
• /
• 1988

본 연구에서는 난류유동이론을 적용하여 2차원 스크린의 후류에 관한 유동특 성을 연구하였다. 이를 위해 적합한 난류모델 및 스크린의 존재를 고려한 수치해석 방법을 연구하였다. 스크린의 저항이 커서 스크린 하류유동이 역류가 되는 경우도 포함하였다.

• 한국농공학회논문집
• /
• 제48권1호
• /
• pp.27-38
• /
• 2006

In this study, we developed a program to estimate discharge efficiently considering major hydraulic characteristic including water level, river bed, water slope and roughness coefficient in a natural river. Stream discharge was measured at Gongju gauge station located in the down stream of the Daechung Dam during normal and dry seasons from 2003 to 2004. The developed model was compared with the results from the existing rating curve at T/M gage stations, and was used for runoff analyses. Evaluating the developed river discharge estimation program, it was applied during 1983-2004 that base flow separation method and RRFS (Rainfall Runoff Forecasting System) which is based on SSARR (Streamflow Synthesis And Resevoir Regulation). The result presents the stage-discharge curve creator range at the Gong-ju is overestimated by approximately $10-20\%$, especially at the low stage. It is attributed to the hydraulic characteristics at the study. The discharge simulated by the RRFS and base flow separation, which is calibrated using the measurement at the early spring and late fall season during relatively d]v season, shows the least errors. The coefficient of roughness at Gongju station varied with the high and low water level.

• 보건행정학회지
• /
• 제14권3호
• /
• pp.20-44
• /
• 2004

The National Health Insurance Expenditure has been increased rapidly since the introduction of the separation of prescription and dispensing in 2000, and this trend of rapid growth in overall spendings rate has been observed predominantly among medical practitioners. This study was conducted to investigate the growth rate and distributional changes in private medical practitioners' expenses from 1999 to 2002 and its determinants using the National Health Insurance claims data. The total increasing rate of all medical practitioners' expenditure paid by the National Health Insurance between 1999 and 2002 was $41.71\%$, which exceeding that of general hospitals by $20\%$p. But the income distribution among each practitioner was improved as the changes in Gini coefficient(from 0.40 to 0.38) and decile distribution ratio(from 0.25 to 0.29) during the same period showed. However, this improvement in distributional patterns is not enough since even in 2002 it turned out that the highest $10\%$ income group earned 33times more than the lowest $10\%$ income group did. Also, higher Gini coefficient was observed in larger cities and some department like plastic surgery, obstetrics and gynecology. The major causes of this differentials in medical practitioners' expenses were factors related to medical demand like proportion of old population, residential economic status in a given area. In addition, providers' economic incentives also played an important role in determining their income distribution. The large income differentials among physicians may imply a skewed distribution of patients and thus long waiting time, inefficient utilization of resources and potential inadequate quality of care. In this sense, unreasonable distributional gaps should be reduced, so effective measures as well as ongoing monitoring would be necessary to correct current distributional problems.

• 한국방재학회 논문집
• /
• 제6권1호
• /
• pp.59-68
• /
• 2006

합류부는 유량의 변화, 흐름방향의 전환으로 순환흐름의 분리구역의 발생에 의한 통수단면의 축소에 의한 통수능의 저하와 이에 따른 배수의 영향이 야기된다. 지류와 본류와의 유량비와 합류각을 달리하면서 실험한 결과를 이용하여 분리구역의 특성을 규명하였다. 분리구역의 정의는 유함수를 이용하여 그 값이 0(영)인 유선을 분리구역으로 정의하여 그 길이와 폭을 본류 하천폭으로 나눈 무차원 길이비와 무차원 폭비로 하였고, 유선에 의한 분리구역의 연구결과가 기존의 실험들과 비교적 잘 맞는 것으로 나타났다. 작은 유량비와 합류각 30도에서는 분리구역이 나타나지 않아서 유량비와 합류각에 의한 분리구역의 출현경계식을 만들었다. 분리구역에 대한 고찰로 합류각, 유량비, 그리고 본류 하류에서의 Froude수에 의한 분리구역의 무차원 길이비와 폭비에 대한 기존의 실험식을 수정하였고, 수굴계수와 형상지수의 수리적 특성을 분석하였다. 일반적으로 유량비와 합류각이 커질수록 분리구역이 크게 나타났다. 합류부를 전후한 상하류 구간에서 수면의 추적에서 유량비와 합류각이 커질수록 배수위의 영향이 크게 나타났고, 합류부가 접하는 내측보다 외측의 배수영향이 크게 나타났다. 하류부 유량에 의해 등류수심을 산정하여 합류가 시작되는 점에서부터 하류의 등류수심에 이르는 곳까지의 거리를 $X_l$로 보고 합류각과 유량비와 단면폭 및 수축계수간의 상관관계식을 산출하였다. 유량비와 합류각에 따른 수로내의 배수위에 의한 최대수위와 분리구역에서의 최소수심과의 비를 분석하였다.

• 대한기계학회논문집B
• /
• 제27권7호
• /
• pp.948-955
• /
• 2003

Pressure coefficient in rotating discharge hole was measured to gain insight into the influence of rotation to the discharge characteristics of rotating discharge hole. Pressure measurements were done by the telemetry system that had been developed by the authors. The telemetry system measures static pressure using piezoresistive pressure sensors. Pressure coefficients in rotating discharge hole were measured in longitudinal direction and circumferential direction with various rotating speed and 3 pressure ratios. From the results, the pressure coefficient, and therefore the discharge coefficient, is known to decrease with the increase of Ro number owing to the increase of flow approaching angle to the discharge hole inlet. However, there exists critical Ro number where the decrease rate of discharge coefficient with the increase of Ro number changes abruptly; flow separation occurs from the discharge hole exit at this critical Ro number. Critical Ro number increases with the increase of length-to-diameter ratio, but the increase is small where the length-to-diameter ratio is higher than 3. The decrease rate of discharge coefficient with the increase of Ro number depends on the pressure recovery at the discharge hole, and the rate is different from each length-to-diameter ratio; it has tendency that the short discharge hole shows higher decrease rate of discharge coefficient.

• 한국물환경학회지
• /
• 제37권1호
• /
• pp.10-19
• /
• 2021

In the flotation process to remove microplastic (MP) particles, the attachment and separation efficiency is determined by the basic physicochemical characteristics of MP particles as well as bubbles. To evaluate the flotation characteristics of MP particles, we carried out a series of simulations using the population balance (PB) model. The initial attachment coefficient (αo) of MP particles was in the range of 0.2-0.275, and it was slightly lower than that of typical particles, such as clay, debris and algae particles, which exist in water bodies, αo, 0.3-0.4. The relative bubble number (RBN) attached to the surface of the typical number of bubbles was 0.30 and 0.32 for MP 30 ㎛ and MP 58 ㎛, respectively. In comparison, the RBN of larger MP particles (138 ㎛) was as high as 0.53. Furthermore, smaller microbubbles were required to separate properly or additional treatment needed to be applied to enhance collision and attachment efficiency since the flotation of MP particles was found to be difficult to treat as high-rate. As a result of comparing the removal rate (experimental value) of MP particles obtained from the batch-type flotation apparatus and the flotation removal rate (predicted value) of MP obtained through the PB model, the final particles by the particle size of MP overall except for the initial separation time area. With respect to the removal efficiency, the observed and predicted values were similar, and it was confirmed that the floating separation characteristics and evaluation of the MP particles through the PB model could be possible.

• Bulletin of the Korean Chemical Society
• /
• 제28권3호
• /
• pp.451-456
• /
• 2007

Tetraazamacrocyclic ion exchangers tethered to Merrifield peptide resin (DTDM, TTTM) were prepared and the ion exchange capacity of these was characterized. The isotope separation of lithium was determined using breakthrough method of column chromatography. The isotope separation coefficient was strongly dependent on the ligand structure by Glueckauf's theory. We found that the isotope separation coefficients were increased as the values of distribution coefficients were increased. In this experiment the lighter isotope, 6Li was enriched in the resin phase, while the heavier isotope, 7Li in the solution phase. The ion radius of lighter isotope, 6Li was shorter than the heavier isotope, 7Li. The hydration number of lithium ion with the same charge became small as mass number was decreased. Because 6Li was more strongly retained in the resin than 7Li, the isotopes of lithium were separated with subsequent enrichment in the resin phase.

• 한국물환경학회지
• /
• 제20권4호
• /
• pp.307-312
• /
• 2004

This study was focused on experiment for the separation and concentration process of Cu(II), Zn(II) solution with the variation of applied pressure and concentration using reverse osmosis plate and frame modules. Rejection coefficient and degree of concentration for Cu(II) component using single and multi-stage reverse osmosis process were showed 96.3~97.8%, 0.044~0.191(in single-stage), 96.3~98.4%, 0.400~2.264(in multi-stage) within the range of experimental condition, respectively. Those of Zn(II) were 93.3~97.1%, 0.019~0.395(in single-stage), 96.3~98.2%, 0.365~1.454(in multi-stage), respectively. Degree of concentration of multi-stage were higher than those of single-stage. Heavy metal[Cu(II), Zn(II)] separation was very efficient in using reverse osmosis plate and frame type modules. Separation efficiency for a mixed solution Cu(II) and Zn(II) was higher than those of each one of Cu(II) and Zn(II).

• 한국자동차공학회논문집
• /
• 제13권4호
• /
• pp.190-196
• /
• 2005

The power steering hose assembly is usually manufactured through the swaging process, which is conducted to connect a hose with metal fittings. In this process the hose is inserted into metal components, the sleeve and the nipple, and compressed in the radial direction by the jaws to clamp the hose with metal components. In case that the clamping force is small, the oil in the hose can leak locally under the severe operating conditions. To confirm the clamping force requirements, the measurement of separation force in longitudinal direction of the hose is usually performed. In this study, the swaging process of a hose is simulated with the finite element method, to investigate the effect of friction coefficient on the separation fDrce. The results interpretations are ffcused on the inner rubber component, and also a formula is proposed to estimate the separation farces with respect to friction coefficients.

• Nuclear Engineering and Technology
• /
• 제47권7호
• /
• pp.867-874
• /
• 2015

Separation of cesium chloride (CsCl) and strontium chloride ($SrCl_2$) from the lithium chloride-potassium chloride (LiCl-KCl) salt was studied using a melt crystallization process similar to the reverse vertical Bridgeman growth technique. A ternary $SrCl_2-LiCl-KCl$ salt was explored at similar growth rates (1.8-5 mm/h) and compared with CsCl ternary results to identify similarities. Quaternary experiments were also conducted and compared with the ternary cases to identify trends and possible limitations to the separations process. In the ternary case, as much as 68% of the total salt could be recycled per batch process. In the quaternary experiments, separation of Cs and Sr was nearly identical at the slower rates; however, as the growth rate increased, $SrCl_2$ separated more easily than CsCl. The quaternary results show less separation and rate dependence than in both ternary cases. As an estimated result, only 51% of the total salt could be recycled per batch. Furthermore, two models have been explored to further understand the growth process and separation. A comparison of the experimental and modeling results reveals that the nonmixed model fits reasonably well with the ternary and quaternary data sets. A dimensional analysis was performed and a correlation was identified to semipredict the segregation coefficient.