• 한국자동차공학회논문집
• /
• 제16권5호
• /
• pp.92-99
• /
• 2008

This paper describes an signal processing method for the hall sensorless position control of ETC control system using a BLDC motor. The proposed ETC control system, which is mainly consisted of a BLDC motor, a throttle plate, a return spring and reduction gear, has a position sensor with an analog voltage output on the throttle valve instead of BLDC motor for detecting rotor position of motor. So the additional commutation information is necessarily needed to control the mentioned ETC module. In order to estimate and determine the commutation state, it is proposed to properly manipulate the resolution of A/D converter considering the mechanical parameter, that is, the number of motor slot and the ratio of reduction gear. Through this method, the estimation of commutation state for operating the system is possible and the discrete signal for commutation is stably obtained. The validity of the method is examined through the experimental results.

• 전기학회논문지P
• /
• 제59권2호
• /
• pp.135-140
• /
• 2010

This paper presents a sensorless speed control of BLDC Motor using terminal voltage of the one phase. Rotor position information is extracted by indirectly sensing the back EMF from only one of the three terminal voltages for a three-phase BLDC motor. Depending on the terminal voltage sensing rotor position, active filter is used for position information. This leads to a significant reduction in the component device of the sensorless circuit. Therefore this is a advantage for the cost saving and size reduction. With indirect sensing methods based on detection of the terminal voltage that require active filtering, the position information needs the six divider section by PLL circuit, the binary counter and johnson counter by the EPLD. Finally, this algorithm can estimate the rotor position information similar to Hall-sensor sticked the three-phase BLDC motor. As a result, the method described that it is not sensitive to filtering delays, allowing the motor to achieve a good performance over a wide speed range. In addition, a simple starting method and a speed estimation approach are also proposed. Experimental and simulation results are included to verify the proposed scheme.

• 제어로봇시스템학회논문지
• /
• 제19권6호
• /
• pp.508-512
• /
• 2013

In recent years, sensorless drive schemes have been proposed widely and most of them are based on the ZCP (Zero Crossing Point) detection of the BEMF (Back Electro-Motive Force). These schemes have two main problems. One is that ZCP may not be detected at low speed and thus a forced drive is required. The other problem is that there is $30^{\circ}$ phase difference between ZCP and the motor commutation instant and to ensure proper operation, this gap should be accounted for. To solve these problems a circuit is devised for detecting ZCP of the BEMF difference through the line voltage difference. Experimental results show that the output of this circuit is identical to that of the Hall sensor signal, and velocity control of a BLDC motor is possible without the sensor.

• 한국자동차공학회논문집
• /
• 제22권1호
• /
• pp.95-102
• /
• 2014

This paper presents zero crossing point(ZCP) estimation methods considering discretization error for a high speed brushless DC(BLDC) motor drive. The ZCP is estimated by detecting the change of back-EMF polarity for the BLDC sensorless drive, and the discretization error exist on the estimated ZCP. The discretization error of the ZCP is a cause of the delay of a commutation timing of current and increment of a current ripple factor. Besides a delay of a ZCP estimation brings on the limitation of a speed range for the BLDC sensorless drive. The compensation method based on the error analysis with probability theory for reducing the effects of the discretization error of the ZCP is proposed. Also a ZCP estimation method according to the Back-EMF patterns is proposed to widen the speed range for the BLDC sensorless drive. The proposed methods are verified by the experiment.

• 한국정밀공학회지
• /
• 제25권5호
• /
• pp.15-21
• /
• 2008

• 전력전자학회논문지
• /
• 제12권2호
• /
• pp.157-164
• /
• 2007

본 논문에서는 일반적인 브러시리스 전동기의 센서리스 구동 성능을 개전하기 위한 퍼지 역기전력 관측기를 이용한 새로운 센서리스 구동 방법이 제안되었다. 기존의 브러시리스 전동기의 센서리스 구동 방법은 저속영역과 과도상태에서의 성능저하와 추가적인 회로를 필요로 한다. 이러한 문제점을 보완하기 위해 사다리꼴 형태의 역기전력을 추정하기 위해 적합한 퍼지 논리에 의해 브러시리스 전동기의 역기전력을 정확하게 추정하였다. 퍼지 역기전력 관측기를 이용한 제안된 알고리듬은 정상 상태 뿐만 아니라 과도 상태에서도 연속적인 회전자 위치를 추정하고 외부 환경 변화에 강인한 제어를 얻을 수 있다. 제안된 알고리듬의 우수성은 다른 센서리스 구동방법과 비교한 시뮬레이션을 통하여 입증되었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 학술대회 논문집 정보 및 제어부문
• /
• pp.579-583
• /
• 2005

This paper is study for design SOC composing space vector control algorithm of sensorless BLDC motor by H/W and apply this to operating machanism of washing machine system. it is study that increases control efficiency than S/W control algorithm and enhances response for change of system and authoritativeness of controller. Designed so that can compose controller of most suitable in dynamic characteristic of system by design Parameters of each controller to independent block for SOC design connecting to 8051 cores. For control Sensorless BLDC motor to drive system of washing machine, applied to H/W SVPWM control, so improved authoritativeness of control algorithm and control effectiveness than S/W control algorithm

• 산업기술연구
• /
• 제29권B호
• /
• pp.165-171
• /
• 2009

This paper proposes a sensorless control method of BLDC motors using line-to-line back-EMFs. Typical sensorless control methods have various problems such as the difficulty in operation at low speed and difficulties in application and so forth. However, the control method using line-to-line back-EMFs that this paper proposes solved not only such problems but also problems of noise and difficulty of commutation detection. The method is to divide line-to-line back EMF into the constant. With 550[W] BLDC motor driving system, simulations and experiments have been carried out for the verification of the proposed control method.

• 조명전기설비학회논문지
• /
• 제22권10호
• /
• pp.97-103
• /
• 2008

최근 가전제품에 브러시리스 직류 (Brushless DC) 전동기의 센서리스 드라이브를 적용시키는 사례가 증가하고 있다. 특히 사람들의 삶의 질이 향상 됨에 따라 가정에서 가장 밀접하게 연관되어 있는 냉장고, 에어컨과 같은 가전제품에 가청소음을 줄여 보다 편안하고 안락한 생활을 추구하고 있다. 본 논문에서는 브러시리스 직류전동기에 랜덤 PWM을 적용한 냉장고용 압축기의 저가형 센서리스 드라이브를 이용하여 기존 드라이브 보다 가격과 소음을 줄일 수 있음을 실험하였다. 이러한 실험으로 전자적 소음을 줄임으로써 소음에 질을 향상시킬 수 있음을 확인할 수 있었다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2007년도 하계학술대회 논문집
• /
• pp.325-327
• /
• 2007

This paper proposes a novel sensorless fault detection algorithm for a brushless DC(BLDC) motor drive system. This proposed method is configured without the additional sensor for fault detection and identification. The fault detection and identification are achieved by a simple algorithm using the operating characteristic of the BLDC motor. This proposed method can also be embedded into existing BLDC motor drive systems as a subroutine without excessive computational effort. The feasibility of a novel sensorless fault detection algorithm is validated in simulation.