• Journal of the Korea Convergence Society
• /
• v.13 no.4
• /
• pp.53-61
• /
• 2022

Accidents are steadily occurring due to machine defects and carelessness during LNG storage operations. In previous studies, an environmental sensor module capable of measuring pressure, temperature, gas concentration, and flow to detect danger in advance was developed and the response speed according to the amount of leaked gas was measured. This paper proposes the development of a wired and wireless communication module that transmits data measured by the environmental sensor module to embedded devices connected to wired and wireless networks of SPI, UART, and LTE. First, a data communication module capable of interworking with an environmental sensor is designed. Design a protocol between devices in the Local Control Part and wired and wireless protocols in the Local Control Part and Remote Control Part. Ethernet, WiFi, and LTE communication modules were designed, and UART and SPI channels that can be linked with embedded controllers were designed. As a result, it was confirmed through a UI (User Interface) that each embedded device transmits data measured by the environmental sensor module while simultaneously communicating on a wired and wireless basis.

• Smart Structures and Systems
• /
• v.6 no.5_6
• /
• pp.689-709
• /
• 2010

In this paper, a low cost, low power but multifunctional wireless sensor node is presented for the impedance-based SHM using piezoelectric sensors. Firstly, a miniaturized impedance measuring chip device is utilized for low cost and low power structural excitation/sensing. Then, structural damage detection/sensor self-diagnosis algorithms are embedded on the on-board microcontroller. This sensor node uses the power harvested from the solar energy to measure and analyze the impedance data. Simultaneously it monitors temperature on the structure near the piezoelectric sensor and battery power consumption. The wireless sensor node is based on the TinyOS platform for operation, and users can take MATLAB$^{(R)}$ interface for the control of the sensor node through serial communication. In order to validate the performance of this multifunctional wireless impedance sensor node, a series of experimental studies have been carried out for detecting loose bolts and crack damages on lab-scale steel structural members as well as on real steel bridge and building structures. It has been found that the proposed sensor nodes can be effectively used for local wireless health monitoring of structural components and for constructing a low-cost and multifunctional SHM system as "place and forget" wireless sensors.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.5 no.1
• /
• pp.103-110
• /
• 2011

In this paper, we propose a gaze recognition interface for smart wheelchair. The gaze recognition interface is a user interface which recognize the commands using the gaze recognition and avoid the detected obstacles by sensing the distance through range sensors on the way to driving. Smart wheelchair is composed of gaze recognition and tracking module, user interface module, obstacle detector, motor control module, and range sensor module. The interface in this paper uses a camera with built-in infra red filter and 2 LED light sources to see what direction the pupils turn to and can send command codes to control the system, thus it doesn't need any correction process per each person. The results of the experiment showed that the proposed interface can control the system exactly by recognizing user's gaze direction.

• Journal of the Korea Convergence Society
• /
• v.11 no.11
• /
• pp.55-61
• /
• 2020

The communication issues expected for SMEs are that 1) IT systems are not easy to connect, 2) data collection and integration by heterogeneous systems are difficult, and 3) various fieldbuses and protocols make interfaces difficult. Usually, SMEs often have automation built before the introduction of smart factories. It is necessary to provide communication technology such as Sensing to meet the heterogeneous system level with the old aged sensors in the automation equipment and communication network of SMEs. We will consider how to improve the network interface before applying the latest network technology at the time of preparation using PI.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.12A
• /
• pp.1261-1269
• /
• 2008

This paper presents an implementation of the Network Capable Application Processor (NCAP) and the Wireless Transducer Interface Module (WTIM) architectures based on the new IEEE P1451.5 standard. Proposed architecture is implemented using a computer for NCAP, an FPGA board, a sensor board and two radio modules, which communicate through the ZigBee wireless communication technology between the NCAP and the WTIM based on the IEEE 1451.0 and the IEEE 1451.5 interfaces. In this paper, two experiments has been done to verify operations of proposed architecture. From the experimental results, we verify that the proposed architecture performs the wireless sensor communication functions efficiently.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.22 no.5
• /
• pp.669-674
• /
• 2012

This study presents the remote control of a mobile robot using iPhone based on Wi-Fi communication. The paper proposes the following set of user interfaces : acceleration mode, arrow touch mode, and jog-shuttle mode. To evaluate the proposed three interfaces, a virtual robot is controlled in a monitor to follow a referenced trajectory using iPhone. In simulation, the standard deviation and summed errors are analysed for showing good and weak points of the proposed three interfaces. The proposed interface replace an additional remote controller requiring cost with a cellular phone. Results of an experiment show that the proposed interfaces can be effectively used for remote robot control.

• Smart Media Journal
• /
• v.8 no.1
• /
• pp.51-58
• /
• 2019

This paper describes a gesture application to controlling the special effects of physical devices for 4D contents using the PWM (Pulse Width Modulation) method. The user operation recognized by the infrared sensor is interpreted as a command for 3D content control, several of which manipulate the device that generates the special effect to display the physical stimulus to the user. With the content controlled under the NUI (Natural User Interface) technique, the user can be directly put into an immersion experience, which leads to provision of the higher degree of interest and attention. In order to measure the efficiency of the proposed method, we implemented a PWM-based real-time linear control system that manages the parameters of the motion recognition and animation controller using the infrared sensor and transmits the event.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.4
• /
• pp.565-569
• /
• 2014

Recently, various kinds of new computer controlled devices have been introduced in a wide range of areas, and convenient user interfaces for controlling the devices are strongly needed. To implement natural user interfaces(NUIs) on top of the devices, new technologies like a touch screen, Wii Remote, wearable interfaces, and Microsoft Kinect were presented. This paper presents a natural and intuitive gesture-based model for controlling contents of LCD display. Microsoft Kinect sensor and its SDK are used to recognize human gestures, and the gestures are interpreted into corresponding commands to be executed. A command dispatch model is also proposed in order to handle the commands more naturally. I expect the proposed interface can be used in various fields, including display contents control.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.538-540
• /
• 2004

Electrical currents generated by human heart activities create magnetic fields represented by MCG(MagnetoCardioGram). Since an MCG signal acquisition system requires precise and stable operation, the system adopts hundreds of SQUID(Superconducting QUantum Interface Device) sensors for signal acquisition. Such a system requires fast real-time data acquisition in a required sampling interval, i.e., 1 mili-second for each sensor. This paper presents designed hardware to acquire data from 256-channel analog signal with 1 ksamples/sec speed, using 12-bit 8-channel ADC devices, SPI interfaces, parallel interfaces, 8-bit microprocessors, and a DSP processor. We implemented SPI interface between ADCs and a microprocessor, parallel interfaces between microprocessors. Our result concludes that the data collection can be done in $168{\mu}sec$ time-interval for 256 SQUID sensors, which can be interpreted to 6 ksamples/sec speed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.983-986
• /
• 2007

In this paper, we addressed the IEEE 1451.x that can organize a sensor network for efficient measurement system. IEEE 1451 provides standard interface, specification and Object model for example Network Capable Application Processor(NCAP), Transducer Electronic Data Sheet(TEDS), Smart Transducer Interface Module (STIM) and so on. Especially IEEE 1451.2 defines the TEDS Formats and STIM. The TEDS makes transducer to be used independently from device. NCAP makes the component of measurement system to be handled as an object. Therefore each function block constructs system by using Add-on. IEEE 1451.x can be expend the system with Add-on and Plug-and-Play by using smart sensor and connected with current network. We expect that this method can provide the efficiency and convenience when using the measurement system.