• Journal of the Institute of Electronics Engineers of Korea SD
• /
• 제48권11호
• /
• pp.9-17
• /
• 2011

As semiconductor process rapidly developed, the density of chips becomes higher and the space between adjacent lines narrows smaller. This trend increases the capacitance and inductance in interconnects and the coupling-capacitance of adjacent lines grows even bigger than the self-capacitance of themselves, especially in global interconnects. Inductive and capacitive coupling observed in these phenomena may cause serious problems in signal integrity. This paper proposes a codeword generation technique using extra interconnect lines to reduce the crosstalk caused by inductive and capacitive coupling and to reduce dynamic power consumption considering probability of input data. To estimate the performance of the proposed technique, the experimental results have been obtained using FastCap, FastHenry and HSPICE, and it has been shown that the power consumption using the proposed technique has yielded approximately 15% less than the results of the previous technique.

• International Journal of Aeronautical and Space Sciences
• /
• 제17권4호
• /
• pp.501-517
• /
• 2016

Synchronized switch damping (SSD) is a structural vibration control technique in which a piezoelectric patch attached to or embedded into the structure is connected to or disconnected from the shunt circuit in order to dissipate the vibration energy of the host structure. The switching process is performed by a digital signal processor (DSP) which detects the displacement extrema and generates a command to operate the switch in synchronous with the structure motion. Recently, autonomous SSD techniques have emerged in which the work of DSP is taken up by a low pass filter, thus making the whole system autonomous or self-powered. The control performance of the previous autonomous SSD techniques heavily relied on the electrical quality factor of the shunt circuit which limited their damping performance. Thus in order to reduce the influence of the electrical quality factor on the damping performance, a new autonomous SSD technique is proposed in this paper in which a negative capacitor is used along with the inductor in the shunt circuit. Only a negative capacitor could also be used instead of inductor but it caused saturation of negative capacitor in the absence of an inductor due to high current generated during the switching process. The presence of inductor in the shunt circuit of negative capacitor limits the amount of current supplied by the negative capacitance, thus improving the damping performance. In order to judge the control performance of proposed autonomous SSDNCI, a comparison is made between the autonomous SSDI, autonomous SSDNC and autonomous SSDNCI techniques for the control of an aluminum cantilever beam subjected to both single mode and multimode excitation. A value of negative capacitance slightly greater than the piezoelectric patch capacitance gave the optimum damping results. Experiment results confirmed the effectiveness of the proposed autonomous SSDNCI technique as compared to the previous techniques. Some limitations and drawbacks of the proposed technique are also discussed.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• 제53권3호
• /
• pp.149-156
• /
• 2004

This paper deals with the effective protection method for the household electric appliances against lightning surges invading from the Power lines. Direct or induced lightning is the main cause of the breakdown of household electric appliance. The most effective protection method is to install SPDs(surge protective devices) at household electric appliances. If SPDs were not installed at most household electric appliances, it is necessary to install SPDs on the mains. Therefore the propagation aspect and protection methods of lighting surges coming into household electric appliances through the mains was experimentally investigated. The in actual-sized test circuits results of protection method for 8 household electric appliances including computer monitors and TV set could be summarized as follows: The breakdown characteristics of household electric appliances from lightning surges were significantly changed with the their input impedance. Namely, the types of input impedance are classified into infinite, resistive or inductive impedances. Especially, the monitor for computer with inductive input impedance from lightning surges was relatively weak against lightning surges. It was confirmed that the self inductance of branch circuits on the mains have protection effect for household electric appliances against lightning surges invading from the power lines. Also the varistors installed at cabinet panel or circuit-breaker were more effective than multi-tap outlet with varistors. When installed varistors in cabinet panel and multi-tap outlet together, the surge protection effect is much more excellent in technical and economical aspects.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• 제39권4호
• /
• pp.409-412
• /
• 2002

The LNA(Low Noise Amplifier) is designed for use in low cost commercial application covered fully IMT-2000 band(1920~2170MHz, BW=250MHz). It is optimized source inductance for source lead and designed to equivalent etched line. The LNA uses a high pass impedance matching network for noise match and simple structure. The bias circuit designs have been made self-biased with a negative voltage applied to gate. The power supply voltage is 8V, total current is 180mA. The LNA is biased at a Vgs of -0.4, Vds of 4V for first stage and Vds of 5V for second stage. The LNA is designed competitively for commercial product specification. The measured gain and noise figure of the completed amplifier was 20dB and 1dB, respectively. Also, input VSWR, P1dB and gain flatness was measured of 1.14 ~ l.3dB, 22.4dBm and $\pm$0.45dB, respectively. The designed LNA can be used for commercial product.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• 제39권10호
• /
• pp.995-999
• /
• 2015

Inductive sensors are versatile and economical devices that are widely used to measure a wide variety of physical variables, such as displacement, force, and pressure. In this paper, we propose a simple inductive sensor consisting of a thin partial ring and a coil set. The self-inductance of the sensor was estimated using magnetic circuit analysis and validated through finite element analysis (FEA). The natural frequency of the ring was estimated using Castigliano's theorem and the method of equivalent mass. The estimation was validated through experiments and FEA. A prototype sensor with a signal processing circuit is built and applied to noninvasively sense the pressure inside a flexible tube. The obtained sensor outputs show quadratic behavior with respect to the pressure. When fitted to a quadratic equation, the least-square measurement error was less than 2%. The results confirm the feasibility of pressure sensing using the proposed inductive sensor.

• Journal of the Microelectronics and Packaging Society
• /
• 제28권2호
• /
• pp.81-88
• /
• 2021

In this paper, by applying LTCC substrate, the library of the passive elements is implemented. And it can be used in 24 GHz circuits. Depending on how to use it to the circuit, it is required large value by designing the basic structures such as electrode capacitor and spiral inductor. However they are not available in high-frequency domain, because their SRF(Self-Resonant Frequency) is lower than the frequency of 24-GHz. By solving the limit, this paper devised passive elements classified for the DC and the high-frequency domain. The basic structure is suitable for low frequency under 1~2 GHz like DC. The microstrip λ/8 length stub structure is proposed to use for high-frequency like 24-GHz. The open and short stub structure operate as a capacitor and inductor respectively, also they have their impedances. Through their impedances, we can extract the value with the impedance-related equation. In this paper, the proposed passive elements are produced with the permittivity 7.5 LTCC substrate, the basic structure which are available in the DC constituted a library of capacitance of 2.35 to 30.44 pF and inductance of 0.75 to 5.45 nH, measured respectively. The stub structure available in the high-frequency domain were built libraries of capacitance of 0.44 to 2.89 pF and inductance of 0.71 to 1.56 nH, calculated respectively. The measurements have proven how to diversify value, so libraries can be built more variously. It will be an alternative to the passive elements that it is possible to integrate with the operation circuit of radar module for the frequency 24-GHz.

• Journal of the Microelectronics and Packaging Society
• /
• 제27권4호
• /
• pp.67-75
• /
• 2020

In this paper, by applying LCP substrate, the capacitor and inductor are implemented with a variety of value that can be used in 35 GHz circuits. Depending on how to apply it to the circuit, it is required high value by designing the basic structures such as electrode capacitor and spiral inductor. However they are not available in high-frequency domain, because their SRF(Self-Resonant Frequency) is lower than the frequency of 35-GHz. By finding the limit, this paper devised classifying passive devices for the DC and the high-frequency domain. The basic structure is suitable for DC and microstrip λ/8 length stub structure can be used for high-frequency. The open and short stub structure operate as a capacitor and inductor respectively in the frequency of 35 GHz. If their impedance is known, it is possible to extract the value through the impedance-related equation. By producing with the permittivity 2.9 LCP substrate, the basic structure which are available in the DC constituted a library of capacitance of 1.12 to 13.9 pF and inductance of 0.96 to 4.69 nH, measured respectively. The stub structure available in the high-frequency domain were built libraries of capacitance of 0.07 to 2.88 pF and inductance of 0.34 to 1.27 nH, calculated respectively. The measurements have proven how to diversify value, so libraries can be built more variously. It is possible to integrate with the operation circuit of TRM(Transmit-Receive Module) for the frequency 35-GHz, it will be an alternative to the passive devices that can be properly utilized in the circuit.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• 제37권1호
• /
• pp.8-18
• /
• 2000

We presented a BGA(Ball Grid Array) package for RF circuit modules and extracted its electrical parameters. As the frequency of RF system devices increases, the effect of its electrical parasitics in the wireless communication system requires new structure of RF circuit modules because of its needs to be considered of electrical performance for minimization and module mobility. RF circuit modules with BGA packages can provide some advantages such as minimization, shorter circuit routing, and noise improvement by reducing electrical noise affected to analog and digital mixed circuits, etc. We constructed a BGA package of ITS(Intelligent Transportation System) RF module and measured electrical parameters with a TDR(Time Domain Reflectometry) equipment and compared its electrical parasitic parameters with PCB RF circuits. With a BGA substrate of 3${\times}$3 input and output terminals, we have found that self capacitance of BGA solder ball is 68.6fF, and self inductance 146pH, whose values were reduced to 34% and 47% of the value of QFP package structure. S11 parameter measurement with a HP4396B Network Analyzer showed the resonance frequency of 1.55GHz and the loss of 0.26dB. Routing length of the substrate was reduced to 39.8mm. Thus, we may improve electrical performance when we use BGA package structures in the design of RF circuit modules.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• 제24권2호
• /
• pp.152-160
• /
• 2013

In this paper, to the aim of wideband SSN(Simultaneous Switching Noise) suppression characteristic, investigation of spiral resonator are used in conjunction with bead which is commonly used for noise suppression method. Bead works effectively to suppress the power noise up to the first harmonic of fundamental frequency, 0.8 GHz, and spiral resonator suppress noise well in the frequency range of SRF(Self Resonance Frequency) which is inversely proportional to the length of spiral. Thus, when bead used in conjunction with a spiral the noise suppression characteristic is determined by the one of higher impedance element of the two in the frequency range and achieves more broadband filtering characteristic. The case for using 22 nH bead turns out 4.8, 2.0, 0, and, 0.6 dB, and the case for using 22 nH bead in conjunction with 3-turns spiral achieves more wideband characteristic of 9.5, 8.3, 6.1, and 9.9 dB power noise suppression performances at the first, second, third, and fourth harmonics, respectively. The peak-to-peak voltage levels decrease from 76 mV to 56 mV using 22 nH bead, and the level decrease rapidly to 34 mV when using in conjunction with bead and 3-turn spiral. Thus more wideband SSN suppression characteristic can be achieved using bead with spiral.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• 제37권6호
• /
• pp.34-42
• /
• 2000

Recently, there is a growing need to develope small-size RF chip inductors operating to GHz to realize high-performance, micro-fabricated wireless communication products. For the development of high-performance RF chip inductors, however, the ferrite-based chip inductors can not be used above 300MHz due to the limitation of the permeability of this material. In this work, small-size, high-performance RF chip inductors utilizing amorphous $Al_2O_3$ core material were investigated. Copper (Cu) with 40${\mu}m$ diameter was used as the coils and the chip inductor size fabricated in this work is $2.1mm{\times}1.5mm{\times}1.0mm$. The external current source was applied after bonding Cu coil leads to gold pads electro-plated on the bottom edges of a core material. The composition of core materials was measured using a EDX. High frequency characteristics of the inductance (L), quality factor (Q), and impedance (Z) of developed inductors were measured using an RF Impedance/Material Analyzer (HP4291B with HP16193A test fixture). The developed inductors have the self-resonant frequency (SRF) of 1 to 3.5 GHz and exhibit L of 22 to 150 nH. The L of the inductors decreases with increasing the SRF. The Z of the inductors has the maximum value at the SRF and the inductors have the quality factor of 70 to 97 in the frequency range of 500 MHz to 1.5 GHz.