• Korean Journal of Applied Biomechanics
• /
• v.22 no.2
• /
• pp.201-208
• /
• 2012

The purpose of this study was to investigate the effect of leg extension exercises performed on outdoor resistance exercise machines on knee extension muscle strength and quadriceps muscle group cross sectional area (CSA) in elderly women. Two groups were recruited for this study, including an exercise group (EG: n=13, $71.38{\pm}2.79$ yrs) and a control group (CG: n=5, $73.4{\pm}5.94$), In all subjects, maximum isometric and isokinetic muscle strength of knee flexion and extension were measured using an isokinetic dynamometer (Cybex(R) Humac Norm Testing & Rehabilitation System, USA). Quadriceps muscle group CSA were measured using MRI (Philps, Intera 1.5 T, NE Netherlands). The results of this study showed that post-intervention isometric knee extension peak torque value were higher than pre-intervention measures in the EG. However, the EG did not show improvement in quadriceps muscle group CSA, Also, no differences in the shift of optimal knee joint angle were observed between pre and post-intervention exercise. Outdoor leg extension exercise showed small increases in muscle strength in comparison to other resistance training exercises. The results of this study suggest that because outdoor leg extension exercise machines lack a progressive loading mechanism, significant increases in muscle strength may not be obtained.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.269-281
• /
• 2010

The cone penetration test(CPT) has been increasingly used for in situ site characterization. However, the use of CPT is often limited due to specific site conditions depending on the cone size, geometry, and capacity of the CPT system used. In South Korea, it has generally been considered that the CPT could be satisfactorily performed only in soft soils. Louisiana State University/ Louisiana Transportation Research Center has implemented a field-rugged continuous intrusion miniature cone penetration test (CIMCPT) system since the 1990s. The miniature cone penetrometer of the CIMCPT system has a cross-sectional cone area of $2cm^2$ allowing finer soil profiles compared to the standard $10cm^2$. The reduced cross-sectional area also enables a system capacity reduction leading to cost saving and ease in maintenance. In addition, the continuous intrusion mechanism allows fast and economic site investigations. Samsung C&T Corporation has recently implemented a similar CIMCPT system. In this study, case studies on the field application of Samsung CIMCPT system for the last 2 years are presented to illustrate its performance investigation and its usefulness and limitation. Results of the case studies show that the CIMCPT system can be applied to soils with cone tip resistance($q_c$) values up to about 30MPa and allows a reliable and useful way to characterize soft soils. The results also show that the rod buckling limits the investigation depth by the system and the large contact pressure of the CIMCPT truck prevents the use of the system at sites with soft surface soils. According to the results of the case studies, the Samsung CIMCPT system has been being upgraded with a miniature cone with a longer rod, a crawler-type transportation system, a pre-boring system, and so on.

• Journal of Korean Neurosurgical Society
• /
• v.58 no.4
• /
• pp.357-362
• /
• 2015

Objective : To investigate risk factors for S1 screw loosening after lumbosacral fusion, including spinopelvic parameters and paraspinal muscles. Methods : We studied with 156 patients with degenerative lumbar disease who underwent lumbosacral interbody fusion and pedicle screw fixation including the level of L5-S1 between 2005 and 2012. The patients were divided into loosening and non-loosening groups. Screw loosening was defined as a halo sign larger than 1 mm around a screw. We checked cross sectional area of paraspinal muscles, mean signal intensity of the muscles on T2 weight MRI as a degree of fatty degeneration, spinopelvic parameters, bone mineral density, number of fusion level, and the characteristic of S1 screw. Results : Twenty seven patients showed S1 screw loosening, which is 24.4% of total. The mean duration for S1 screw loosening was $7.3{\pm}4.1$ months after surgery. Statistically significant risk factors were increased age, poor BMD, 3 or more fusion levels (p<0.05). Among spinopelvic parameters, a high pelvic incidence (p<0.01), a greater difference between pelvic incidence and lumbar lordotic angle preoperatively (p<0.01) and postoperatively (p<0.05). Smaller cross-sectional area and high T2 signal intensity in both multifidus and erector spinae muscles were also significant muscular risk factors (p<0.05). Small converging angle (p<0.001) and short intraosseous length (p<0.05) of S1 screw were significant screw related risk factors (p<0.05). Conclusion : In addition to well known risk factors, spinopelvic parameters and the degeneration of paraspinal muscles also showed significant effects on the S1 screw loosening.

• Journal of Korea Water Resources Association
• /
• v.42 no.10
• /
• pp.867-876
• /
• 2009

In this study, the stage-discharge relation curve made in 2006 is selected with standard curves to seize the hydraulic and geometric characteristics for the temporal variation of the river bed. The relationships among the standard stage-discharge relation curve and the existing stage-discharge relation curves, water level, cross sectional area, and flow velocity are analyzed. Jeokpogyo and Jindong which are the key station of Nakdong river are chosen for the study, with respect to the current river bed to convert the existing stage-discharge curves. The relationships for conversion of previous data, between water level and flow velocity are got. Also the relation equation between water level and cross sectional area and water level, flow velocity are derived. These conversion relationships shows good agreement between observed values and estimated values. It will be very useful to convert past hydraulic quantitations to current one.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.41
• /
• pp.51.1-51.8
• /
• 2019

Purpose: It has been reported before that the amount of pharyngeal airway space (PAS) significantly decreases following mandibular setback (MS) surgery in patients with mandibular prognathism (MP). Further, MP patients with an anterior open-bite (AOB) presentation may show a larger decrease in PAS compared with those without AOB. However, studies on postoperative PAS changes in MP patients with AOB remain rare. This study sought to evaluate changes in PAS and hyoid bone positioning following MS surgery in MP patients with and without AOB. Patients and methods: Twenty patients who underwent two jaw surgery involving MS movement were included. Patients were divided into a non-AOB group (n = 10; overbite > 2 mm) and an AOB group (n = 10; overbite < - 4 mm). Three-dimensional changes in PAS and hyoid bone positioning were compared and statistically evaluated pre- and postoperatively using computed tomography (CT). Results: The mean magnitude of MS was 6.0 ± 2.8 mm and 5.6 ± 3.2 mm in the non-AOB group and AOB group, respectively. The oropharyngeal volume and upper hypopharyngeal volume were significantly reduced after surgery in both the groups (p = 0.006 and p = 0.003), while the retroglossal cross-sectional area was significantly reduced only in the AOB group (p = 0.028). Although the AOB group showed a larger decrease in PAS, the difference was not statistically significant between the groups. The position of the hyoid bone showed significant posterior and inferior displacement only in the AOB group, while the vertical displacement of the hyoid bone showed a statistically significant difference between the two groups. Conclusion: PAS was significantly decreased after MS in both the groups, while only the AOB group presented a statistically significant reduction in the retroglossal cross-sectional area. Vertical displacement of the hyoid bone showed a statistically significant difference between the groups, while the PAS change was not. Surgeons should be aware of potential postoperative airway problems that may arise when performing MS surgeries.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.393-396
• /
• 2008

The purpose of this paper is to find out quantitatively the relationship between the surface shape and the mechanical properties of corroded reinforcement. Three-dimensional measurements were carried out on the surface shape of variously corroded reinforcements and parameters expressing the characteristics of the shape, which included the maximum decrement of sectional area of reinforcement, its distribution along the axis. It was investigated that which parameters could correspond to the mechanical properties of corroded reinforcement and it was confirmed that the maximum decrement of sectional area of reinforcement could express the mechanical properties most appropriately. Finally, this paper proposes a constitutive model of corroded reinforcement for analyzing the structural behavior of reinforced concrete structures considering the localized corrosion of by finite element method.

• Journal of Physiology & Pathology in Korean Medicine
• /
• v.23 no.5
• /
• pp.1025-1034
• /
• 2009

This study was carried out to examine the protective effect of Cultured Wild Ginseng(CWG) on the acute and subacute toxicities induced by doxorubicin(Doxo) in mice. Heart and liver weight was decreased following Doxo administration. In contrast, such a decrease was significantly attenuated by CWG administration. The value of serum CPK in Doxo group was increased compared with normal group. But the value of CWG group were decreased significantly compared with the values of Doxo group in the liver of the Doxo group, cloudy swelling of hepatic cells and narrowing of sinusoids were observed. Whereas in the CWG group, well oriented hepatic cell cords and sinusoids were observed. In the testis of the Doxo group, necrotic and degenerative changes of the seminiferous tubules, especially beneath testicular membrane were observed. But those lesions were alleviated in CWG group. Cross sectional area of testis and diameter of semineferous tubule were significantly increased in CWG group compared with Doxo group. Body weight was reduced in Doxo group compared with normal group. In contrast, such a decrease was significantly attenuated by CWG administration atwa5th day. Spermatogenetic cells in seminiferous tubules were necrotic and desquamated and the cellularity of seminiferous epithelia was reduced in Doxo group. But those lesions were attenuated by CWG administration. Cross sectional area of testis and diameter of seminiferous tubule were significantly increased in CWG group compared with Doxo group. In addition, the increase in lipid peroxidation(LPO) in testis was inaddition, the, iout such a increased was significantly inhibited in CWG group. BrdU labelled cells in the seminiferous tubules were remarkably decreased in Doxo group. Whereas the number of seminiferous tubules labelled with BrdU in spermatogonia was increased by CWG administration. The obtained results suggest that CWG has protective effect on doxorubicin-induced toxicity. This effect might be mediated through the supplementation of vital energy.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.31 no.1
• /
• pp.39-45
• /
• 1999

Refining in papermaking plays an important role in changing fiber properties as well as paper properties. The major effects of refining on pulp fibers are internal and external fibrillation, fiber shortening, and fines formation. Many workers showed that internal fibrillation of the primary refining effects was most influential in improving paper properties. In particular, refining produces separation of fiber walls into several lamellae, thus causing fiber wall swelling with water penetration. This leads to the increase of fiber flexibility and of fiber-to-fiber contact during drying. If the fibers are very flexible, they will be drawn into close contact with each other by the force of surface tension as the water is removed during the drainage process and drying stages. In order to study the effect of fiber wall delamination on paper properties, cross-sectional image of fibers in a natural condition had to be generated without distortion. Finally, it was well recognized that confocal laser scanning microscope (CLSM) could be one of the most efficient tool for creating and quantifying fiber wall delamination in combination with image analysis technique. In this study, the CLSM could be used not only to observe morphological features of transverse views of swollen fibers refined under low and high intensity, but also to investigate the sequence of fiber wall delamination and fiber wall breakage. From the CLSM images, increasing the specific energy or refining decreased the degree of fiber collapse, fiber cross-sectional area, fiber wall thickness and lumen area. High intensity refining produced more external fibrillation.

• Restorative Dentistry and Endodontics
• /
• v.29 no.4
• /
• pp.378-385
• /
• 2004

The purpose of this study was to compare the effects of preparation with GT files and profiles .04 in shaping of root canals and reconstruct the three-dimensional root canal system using micro computed tomography 40 canals of the extracted human mandibular molars were used, and randomly distributed into two experimental groups. In group 1. canals were prepared by GT files. In group 2, Profiles .04. were used. Apical preparation size was #30. For each tooth pre and post operative cross-sectional images were obtained by the micro CT at 50 micron intervals. Pre and post operative cross-sectional images of 1, 2, 3, 5, and 8mm from the apex were compared. For each section. canal area and centering ratio were determined. For each tooth pre- and post-operative root canal volume from the furcation to the apex of the roots was calculated by three-dimensional image software. Following results were obtained: 1. At 8mm from the apex, area of dentin removed by GT rotary file was significantly larger than that by Profile .04. And at the other levels there was not a significant difference. 2. There was a trend for GT rotary file to remain more centered in the canals than Profile .04 at all levels. But at 3mm level. there was a statistically significant difference. 3. In root canal volume increments after instrumentation, there was no significant difference between two groups.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11b
• /
• pp.287-294
• /
• 2000

Calculation of the flexural rigidity value (EI) is indispensable for prescription of deflection characteristics of crop stalks in harvesting□Conventionally□EI has been determined by either average EI of the whole stalk or average EI of each stems divided into node through the calculation method of cantilever with homogeneous section□However□deflection characteristics of crop stalks caused by mechanical operation such as combine harvester were not exactly presumed by these conventional EI through the experiment by authors. Further, actual EI of a stalk changes in company with a change of moisture contents as time passes during the experiment. Finally, efficient calculation method for determining EI is needed in order to improve these problems. In this study, mechanical model based on actual structure of the crop stalk with variety sectional area was proposed. This mechanical model is calculated by the theory of cantilever with continuous stages. Therefore, improvement of both calculating accuracy on EI and efficiency of measuring system was tried. At first, this calculation method was applied to piano wire of which EI was recognized in advance. As a result, EI calculated from this new method coincided approximately with piano wire's EI. Next, applying to crop stalks as same as piano wire, relationship between loads acting on crop stalks and deflection values calculated by EI using this new calculation method was exactly presumed in comparison with conventional method. Further, measuring time of deflection test was greatly reduced. Finally, new calculation method of EI will be available for estimating mechanical characteristics of so many kinds of crop stalks in harvesting operation. Further, in this study, new deflection test using image-processing apparatus by computer will be introduced.