• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.47 no.3
• /
• pp.83-89
• /
• 2010

Scalable routing is one of the key challenges in designing and operating large scale MANETs. Performance of routing protocols proposed so far is only guaranteed under various limitation, i.e., dependent of the number of nodes in the network or needs the location information of destination node. Due to the dependency to the number of nodes in the network, as the number of nodes increases the performance of previous routing protocols degrade dramatically. We propose Cluster Overlay Dynamic Source Routing (CODSR) protocol. We conduct performance analysis by means of computer simulation under various conditions - diameter scaling and density scaling. Developed algorithm outperforms the DSR algorithm, e.g., more than 90% improvement as for the normalized routing load. Operation of CODSR is very simple and we show that the message and time complexity of CODSR is independent of the number of nodes in the network which makes CODSR highly scalable.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.26 no.9
• /
• pp.1405-1411
• /
• 2022

Power management is still an important issue in embedded environments as hardware advances like high-performance processors. Power management methods such as DVFS control CPU frequencies in an adaptive manner for efficient power management in polling-based I/O programs such as network communication. This paper presents the problems of the existing power management method and proposes a new power management method. Through this, it is possible to reduce electric consumption by increasing the polling cycle in situations where the frequency of data reception is low, and on the contrary, in situations where data reception is frequent, it can operate at the maximum frequency without performance degradation. After implementing this as a code layer on the embedded board and observing it through Atmel's Power Debugger, the proposed method showed a performance improvement of up to 30% in energy consumption compared to the existing power management method.

• Structural Engineering and Mechanics
• /
• v.90 no.5
• /
• pp.467-480
• /
• 2024

The mechanical properties and durability of concrete pavements may be degraded in extreme situations, resulting in the need for partial repair or total replacement. During the past few decades, there has been a growing body of research on substituting a portion of Portland cement with alternative cementitious materials for improving concrete properties. In this study, two different configurations of powdered and granulated blast furnace slag were implemented, replacing fine aggregates (by 12 wt.%) and Portland cement (by 0, 20, 40, and 60 wt.%) in the making of roller-compacted concrete (RCC) mixes. The specimens were fabricated to investigate the mechanical properties and durability specifications, involving freeze-thaw, salt-scaling, and water absorption resistance. The experimental results indicated that the optimum mechanical properties of RCC mixes could be achieved when 20-40 wt.% of powdered slag was added to concrete mixes containing slag aggregates. Accordingly, the increases in compressive, tensile, and flexural strengths were 45, 50, and 28%, in comparison to the control specimen at the age of 90 days. Also, incorporating 60 wt.% of powdered slag gave rise to the optimum mix plan in terms of freeze-thaw resistance such that a negligible strength degradation was experienced after 300 cycles. In addition, the optimal moisture content of the proposed RCC mixtures was measured to be in the range of 5 to 6.56%. Furthermore, the partial addition of granulated slag was found to be more advantageous than using entirely natural sand in the improvement of the mechanical and durability characteristics of all mixture plans.

• Journal of Korean Dental Science
• /
• v.9 no.2
• /
• pp.81-89
• /
• 2016

Necrotizing periodontal diseases, especially acute necrotizing ulcerative gingivitis (ANUG), it should be noted, occur abruptly and progress rapidly, eventually causing severe soft-tissue and alveolar bone loss. This report presents the cases of two ANUG patients and provides a brief treatment protocol for easy and effective clinical management. After proper diagnosis, sequential treatment with cessation of mechanical brushing, along with a prescription of systemic antibiotics and chlorhexidine as a mouth rinse, scaling, root planing, and supportive periodontal therapy, was utilized. In all cases discussed in this report, there was marked improvement in a few days. ANUG, though an uncommon disease, can be efficiently managed with proper diagnosis and immediate treatment.

• Proceedings of the KIEE Conference
• /
• 1999.11c
• /
• pp.521-523
• /
• 1999

In this paper, we propose the hybrid fuzzy controller(HFC) and the hybrid auto-tuning algorithm. The proposed HFC combined a PID controller with a fuzzy controller concurrently produces the better output performance such as sensitivity improvement in steady state and robustness in transient state than any other controller. In addition, a hybrid auto-tuning algorithm which consists of genetic algorithm and complex algorithm to automatically generate weighting factor, scaling factors and PID control gains optimizes the output of HFC. As an typical example of non-linear system in control theory an inverted pendulum will be controlled by the suggested HFC and illustrated the performance and applicability of this proposed method by simulation.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.8 no.1
• /
• pp.32-39
• /
• 2008

Tunnel oxide of non-volatile memory (NVM) devices would be very difficult to downscale if ten-year data retention were still needed. This requirement limits further improvement of device performance in terms of programming speed and operating voltages. Consequently, for low-power applications with Fowler-Nordheim programming such as NAND, program and erase voltages are essentially sustained at unacceptably high levels. A promising solution for tunnel oxide scaling is tunnel barrier engineering (TBE), which uses multiple dielectric stacks to enhance field-sensitivity. This allows for shorter writing/erasing times and/or lower operating voltages than single $SiO_2$ tunnel oxide without altering the ten-year data retention constraint. In this paper, two approaches for tunnel barrier engineering are compared: the crested barrier and variable oxide thickness. Key results of TBE and its applications for NVM are also addressed.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.591-592
• /
• 2008

본 논문은 배터리를 이용하는 시스템의 사용시간을 극대화하기 위하여 두 가지 해결책을 제시한다. 첫 번째, 우리는 멀티 프로세서 시스템에서 Dynamic Voltage Scaling(DVS)을 이용하여 에너지 소모를 최소화시킨다. 다른 어프로치와의 큰 차이점은 테스크의 실행 시간을 deadline까지 확장시켜 에너지 소모를 최소화할 뿐만 아니라 테스크의 실행 사이클 수가 감소할것을 고려하여 테스크를 나누어 다른 동작 주파수를 적용 시키고 이를 수학적 방법으로 도출한다. 두 번째, 배터리의 discharge 특성인 capacity rate effect와 recovery effect를 고려하여 프로세서들의 에너지 소모 프로파일을 재구성함으로서 배터리 라이프타임을 최적화시킨다.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.1042-1045
• /
• 2002

The scaling of device dimension and supply voltage with high performance and reliability has been the main subject in the evolution of VLSI technology, The MOSFET structures become susceptible to high field related reliability problems such as hot-electron induced device degradation and dielectric breakdown. HLDBD(HLD Buffered Deposition) is used to decrease junction electric field in this paper. Also we compared the hot carrier characteristics of HLDBD and conventional.

• Korean Journal of Materials Research
• /
• v.17 no.7
• /
• pp.347-351
• /
• 2007

Vertical interconnect technology called 3D stacking has been a major focus of the next generation of IC industries. 3D stacked devices in the vertical dimension give several important advantages over conventional two-dimensional scaling. The most eminent advantage is its performance improvement. Vertical device stacking enhances a performance such as inter-die bandwidth improvements, RC delay mitigation and geometrical routing and placement advantages. At present memory stacking options are of great interest to many industries and research institutes. However, these options are more focused on a form factor reduction rather than the high performance improvements. In order to improve a stacked device performance significantly vertical interconnect technology with wafer level stacking needs to be much more progressed with reduction in inter-wafer pitch and increases in the number of stacked layers. Even though 3D wafer level stacking technology offers many opportunities both in the short term and long term, the full performance benefits of 3D wafer level stacking require technological developments beyond simply the wafer stacking technology itself.

• Journal of Power Electronics
• /
• v.9 no.2
• /
• pp.180-187
• /
• 2009

When converters operate in megahertz range, the passive components and magnetic devices generate high losses. However, the eddy current issues and choices of magnetic cores significantly affect on the design stage. Apart from that, the components' reduction, miniaturization technique and frequency scaling are required as well as improvement in thermal capability, integration technique, circuit topologies and PCB layout optimization. In transformer design, the winding and core losses give great attention to the design stage. From simulation work, it is found that E-25066 material manufactured by AVX could be the most suitable core for high frequency transformer design. By employing planar geometry topology, the material can generate significant power loss savings of more than 67% compared to other materials studied in this work. Furthermore, young researchers can use this information to develop new approaches based on concepts, issues and methodology in the design of magnetic components for high frequency applications.