• 열처리공학회지
• /
• 제15권2호
• /
• pp.93-99
• /
• 2002

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.546-547
• /
• 2007

Magnesium is widely used as a lightweight alloy for car engine components and case of cellular phone. Extraction technologies of magnesium are divided to fused salt electrolysis process and thermal reduction process. In this study, electrolysis magnesium is prepared by fused salt electrolysis process with magnesium chloride. We compared two kinds of mixed salt at 7V. As a result, 47% of current efficiency was obtained by electrolyzing KCl/NaCl/$MgCl_2$ mixed salt bath at $760^{\circ}C$, and purity of the prepared magnesium was over 98%. With this study, we can scale up fused salt electrolysis device and accumulate basic data which will be needed for designing an electrolysis cell.

• 한국재료학회지
• /
• 제11권10호
• /
• pp.820-832
• /
• 2001

In order to obtain the basic data on the optimum conditions of electroforming process for fabricating the micro wiring pattern for plate type micro- motor core, characteristics of plating bath and properties of deposits were studied with various copper plating baths which contain sulfate, fluoborate, pyrophosphate and cyanide salt, respectively. Cathodic polarization, throwing power, internal stress, texture and surface morphology of deposits were observed. Throwing power of plating solution is deeply related to the polarization curves and the values are in the range of +20∼20%. The order of values ate as follows- pyrophosphate, cyanide, sulfate and fluoborate bath. Internal stresses of deposits are tensile in all of the copper plating bath. Thickness of the deposits plated at the center of holes has the highest value in the pyrophosphate bath and K factor, ratio of height and width of deposit, is 1.44. It was confirmed that the pyrophosphate bath was the best one for the electroforming of wire pattern.

• 한국표면공학회지
• /
• 제55권6호
• /
• pp.460-468
• /
• 2022

Due to its high electrical conductivity, low contact resistance, good weldability and high corrosion resi-stance, gold is widely used in electronic components such as connectors and printed circuit boards (PCB). Gold ion salts currently used in gold plating are largely cyan-based salts and non-cyanic salts. The cya-nide bath can be used for both high and low hardness, but the non-cyanide bath can be used for low hardness plating. Potassium gold cyanide (KAu(CN)₂) as a cyanide type and sodium gold sulfite (Na₃[Au(SO)₃]₂) salt as a non-cyanide type are most widely used. Although the cyan bath has excellent performance in plating, potassium gold cyanide (KAu(CN)₂) used in the cyan bath is classified as a poison and a toxic substance and has strong toxicity, which tends to damage the positive photoresist film and make it difficult to form a straight side-wall. There is a need to supplement this. Therefore, it is intended to supplement this with an eco-friendly process using sodium sulfite sodium salt that does not contain cyan. Therefore, the main goal is to form a gold plating layer with a controllable hardness using a non-cyanide gold plating solution. In this study, the composition of a non-cyanide gold plating solution that maintains hardness even after annealing is generated through gold-palladium alloying by adding thallium, a crystal regulator among electrolysis factors affecting the structure and hardness, and changes in plating layer structure and crystallinity before and after annealing the correlation with the hardness.

• 한국세라믹학회지
• /
• 제24권4호
• /
• pp.335-342
• /
• 1987

There were several numbers of studies on chemically strengthening glass. Most of them were strengthened in molten salt bath below transformation range of glass. Apart from them, this study used solution hydration technique by Autoclave. After determining proper concentration of AgNO3 salt solution, experimental condition varied from 4hrs to 16hrs at relatively low temperature (180, 200, 220$^{\circ}C$). The results showed that the Soda-Lime-Silica glass could be strengthened by diffusion mechanism without influence of water above 15% salt solution. Because of Ag+ ion penetration in glass surface, yellow color appeared and decreased transmittance at visible range. Modulus of rupture was increased with the amount of exchange and brittleness was decreased.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.451-451
• /
• 2000

This study aims for the optimization of process conditions in a fixed-bed catalytic reactor system with a circulating molten salt bath, in which partial oxidation of propylene to acrolein takes place. Two-dimensional pseudo-homogeneous model is adopted with estimation of suitable parameters and its validity is corroborated by comparing simulation result with experimental data. The temperature of the molten salt and the feed composition are found to exercise significant influence on the yield of acrolein and the magnitude of hot spot. The temperature of the molten salt is usually kept constant. This study, however, suggests that the temperature of the molten salt must be axially adjusted so that the abrupt peak of hot spot should not appear near the reactor entrance. The yield of acrolein is maximized and the position and the magnitude of hot spot are optimized by the method of the iterative dynamic programming (IDP).

• 한국환경과학회지
• /
• 제12권10호
• /
• pp.1131-1136
• /
• 2003

To examine whether salt stress would alter or not contractility of isolated rat aorta, under anesthesia with sodium pentobarbital(50 mg kg-1 i.p.), male Sprague Dawley rats(300-330 g) were subjected to 0, 50, and 150 mM of sodium chloride at 37$^{\circ}C$ for 60 min. where as the sham group was left at modified Krebs-bicarbonate solution. To measure contractile response of vascular ring preparation isolated from rat was determined in organ bath and was recorded on physiograph connected to isometric transducer. And the strip was checked for expression of heat shock protein(Hsp) by Western blotting. One, three and eight hours later, we measured vascular contractility of isolated rat aorta treated with KCI, phenylephrine from organ bath study. The dose-vascular responses of potassium chloride and phenylephrine showed a little augmentation by NaCl concentration in the strips exposed to NaCl for 8 hours. And the response of relaxation induced by nitroprusside and acetylcholine was not influenced by NaCl stress in isolated aorta ring for 8 hours, respectively. Expression pattern of Hsp 70 of vascular muscle in isolated rat aorta showed a little increase in 150 mM NaCl group at 8 hours after NaCl treatment but not at 3 hours, and Hsp 60 expression of rat aorta was markedly increased in 50 mM NaCl group at 8 hours after NaCl treatment. Taken together, NaCl induced dose-and time dependent accumulation of the Hsp but not affected contraction of rat aorta. These data suggest that short term high salt stress was not sufficient to induce hypertension of rat aorta.

• 대한한의학원전학회지
• /
• 제23권6호
• /
• pp.97-108
• /
• 2010

Salt is a vital inorganic substance to human body and is seasoning in food. It is an absolute alternating factor on fermented food. What's more, in the oriental medicine, it is widely used to raise the pharmacological effect as a component of a prescription when processing a medicine, and when taking the medicine. Though, Importance of salt is often unaware and it is not used in the right way. focusing on "東醫寶鑑 內景篇 Donguibogam-Naegyeong" I categorized the methods of salt's prescription, dose, processing, seasoning, etc. The contents were compared and studied as well. When salt is used as a medicine, It is used as a main medicine, complimentary(aid) medicine, Jjim-Jil(hot towel or bath etc), vomiting medicine and gargling water. when taking the salt water with other medicine, depending on the type of the medicine, boiled salt water, warm alcohol or salt water, mixing powder medicine with salt water etc The methods are diverse. The reason to process medicine with salt or salt water is to bring the pharmacological Qi(energy) down to increase remedial value. When processing a medicine, kneading dough with salt water and the case using food ingredient as medicine salt was used as seasoning. Kneaded mud with salt were used to cover medicine or on the outer surface. This proves that it prevents the dryness and helps the medicine cooked even. Like this, salt is vital and highly-valued medicine in the oriental medicine. learning the right method of using salt and if it were used properly It is considered that it would increase the Pharmacological effect.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.573-573
• /
• 2006

• 한국기계가공학회지
• /
• 제17권3호
• /
• pp.148-154
• /
• 2018

When shooting small arms, the inner surface temperature is heated up to about $700{\sim}1,000^{\circ}C$ by the friction of the bullet and the inner wall of the barrel and the combustion of propellant. High-temperature propellant gas and high-speed movement of the bullet cause corrosion of the inner wall, which is noticeable immediately in front of the chamber. In this study, the mechanical properties of Cr-Mo-V steel, which is the base material, were tested using Taguchi experimental design to find the best nitriding treatment conditions. For the nitriding process, the working time, salt bath temperature, and salt concentration were combined as three conditions and placed in the $L_9(3^4)$, orthogonal array table. The thicknesses of the white layer and the nitrogen diffusion layer were measured after nitriding under each condition in a salt bath furnace. Durability was evaluated by measuring the degree of dispersion through actual shooting because it was difficult to evaluate the mechanical properties of the cylinder inner structure. As a result, it was confirmed that the durability was optimal at $565^{\circ}C$, 1 hour, 0.5%. These optimal conditions were selected by the statistical analysis of the Minitab program(ver.17).