• 해양환경안전학회:학술대회논문집
• /
• 해양환경안전학회 2004년도 추계학술발표회
• /
• pp.137-141
• /
• 2004

선체구조는 기본적으로 판부재의 조합으로 이루어져 있으며, 이러한 판부재는 하중분담 능력에 따라서 전체적인 구조의 강도에 른 영향을 미치게 된다. 또한 각 구조적인 판부재는 개별적으로 거동하는 것이 아니라 전체적인 구조와 연속적으로 작용하게 된다. 선박구조물은 강구조물과 해양구조물에서와는 달리 고정도의 부정정 구조물로 구성되어 있으며 이러한 구조물의 거동을 정확하게 규명하기 위해서는 복잡하게 구성되어 있는 선체판넬 구조를 단순화시켜서 해석에 적용하여야 한다. 본 연구에서는 선체판넬구조의 모델링영역에 따른 최종강도 거동의 차이를 분석하여, 가장 합리적인 모델링영역을 도출하고자 한다. 사용된 해석모델은 실제 상선의 이중저구조에서 사용되는 판넬에서 채택하였으며, 유한요소해석 모델링 시 3가지 서로 다른 해석영역을 제시하여 적요하였다. 본 연구의 목적은 일축압축하중이 작용하는 보강판넬구조에서 서로 다른 모델링영역을 갖는 보강판에서의 최종강도 거동을 분석하여 최적의 해석모델링 영역을 찾는 것이다.

• Safety and Health at Work
• /
• 제7권2호
• /
• pp.130-137
• /
• 2016

At a brewery, the base plate-to-shell weld seam of a $90-m^3$ vertical cylindrical steel tank failed catastrophically. The 4 ton tank "took off" like a rocket leaving its contents behind, and landed on a van, crushing it. The top of the tank reached a height of 30 m. The internal overpressure responsible for the failure was an estimated 60 kPa. A rupture disc rated at < 50 kPa provided overpressure protection and thus prevented the tank from being covered by the European Pressure Equipment Directive. This safeguard failed and it was later discovered that the rupture disc had been installed upside down. The organizational root cause of this incident may be a fundamental lack of appreciation of the hazards of large volumes of low-pressure compressed air or gas. A contributing factor may be that the standard piping and instrumentation diagram (P&ID) symbol for a rupture disc may confuse and lead to incorrect installation. Compressed air systems are ubiquitous. The medium is not toxic or flammable. Such systems however, when operated at "slight overpressure" can store a great deal of energy and thus constitute a hazard that ought to be addressed by safety managers.

• 한국구조물진단유지관리공학회 논문집
• /
• 제25권6호
• /
• pp.185-192
• /
• 2021

본 연구에서는 거푸집 패널이 부착된 실물 스케일의 중공슬래브 Mock-up을 제작하여 즉시 처짐 및 장기 처짐에 대한 플랫 플레이트 중공 슬래브의 안전성을 평가하고자 한다. 중공재가 적용된 Mock-up 실험체의 중공률은 24%로 설계하였다. 콘크리트 블록 하중 재하 시 슬래브의 가장 중앙부의 처짐인 No2의 경우 재하 시 처짐이 8.88mm 발생하였으며 이는 즉시 처짐에 대한 기준 값(l_n/240=17.93mm)에 비하여 안전한 값을 나타내고 있다. 3개월간 처짐 량 계측 결과, 중앙부 처짐 량은 초기 처짐에서 6.792mm 더 추가되어 처짐이 발생하였지만, 이는 국내 구조 기준에서 제시하고 있는 사용하중에 의한 기준 값을 만족하고 있는 것으로 나타났다.

• 해양환경안전학회지
• /
• 제10권2호
• /
• pp.35-39
• /
• 2004

선체구조는 기본적으로 판부재의 조합으로 이루어져 있으며, 이러한 판부재는 하중분담 능력에 따라서 전체적인 구조의 강도에 큰 영향을 미치게 된다. 또한 각 구조적인 판부재는 개별적으로 거동하는 것이 아니라 종합적인 구조로서 작용하게 된다. 선박구조물은 강구조물과 해양구조물에서와는 달리 고정도의 부정정 구조물로 구성되어 있으며, 이러한 구조물의 거동을 정확하게 규명하기 위해서는 복잡하게 구성되어 있는 선체판넬 구조를 단순화시켜서 해석에 적용하여야 한다. 본 연구에서는 선체판넬구조의 모델링영역에 따른 최종강도 거동의 차이를 분석하여, 합리적인 모델링영역을 규명하고자 한다. 사용된 해석모델은 실제 상선의 이중저구조에서 사용되는 판넬에서 채택하였으며, 유한요소해석 모델링 시 3가지 서로 다른 해석영역을 지정하여 적용하였다. 본 연구의 목적은 일축압축하중이 작용하는 보강판넬구조에서 서로 다른 모델링영역을 갖는 보강판에서의 최종강도 거동을 분석하여 최적의 해석모델링 영역을 찾는 것이다.

• 한국산업보건학회지
• /
• 제24권4호
• /
• pp.416-424
• /
• 2014

Objectives: The objective of this study is to analyze the predominant microorganisms in the industry treating MWFs(Metal working fluids). Methods: The bacteria and fungi were collected by agar plate impaction and bulk MWFs in storage tank at 54 sites in 9 shops in South Korea. The dominant bacteria and fungi isolated from agar media were identified by fatty acid analysis and morphological analysis, respectively. Results: Totally 111 dominant bacteria were identified in the process, outdoor, and bulk MWFs. The predominant bacterial genus was Micrococcus and Bacillus in the process and outdoor, Pseudomonas in bulk MWF. Among the identified 119 strains of fungi, Cladosporium and Penicillium genus were dominated. The ratios of bacteria designated biosafety level 2 and 1 were 30% and 21%, respectively. Conclusions: This study has investigated the dominant microorganisms in soluble MWF using industry. And it was useful that the qualitative evaluation method along with quantitative analysis for better understanding of the biological factors in the work environment.

• 대한기계학회논문집A
• /
• 제33권11호
• /
• pp.1187-1194
• /
• 2009

During the last decade, possibility of flaw occurrences has been rapidly increased world-widely as the increase of operating times of petro-chemical facilities. For instance, from a recent in-service inspection, three different sized surface cracks were detected in welding parts of a spherical oxygen holder in Korea. While API579 code provides corresponding engineering assessment procedures to determine crack driving forces, in the present work, numerical analyses are carried out for the cracked oxygen holder to investigate effects of complex geometry, analysis model and residual stress. With regard to the detailed finite element analysis, stress intensity factors are determined from both the full three-dimensional model and equivalent plate model. Also, as an alternative, stress intensity factors are calculated for equivalent plate model by employing the noted influence stress function technique. Finally, parametric structural integrity evaluation of the cracked oxygen holder is conducted in use of failure assessment diagram method, J/T method and DPFAD method. Effects of the geometry and so forth are examined and key findings from the simulations are fully discussed, which enables to determine practical safety margins of spherical components containing a defect.

• Nuclear Engineering and Technology
• /
• 제52권2호
• /
• pp.381-396
• /
• 2020

Investigations of the commercial aircraft impact effect on nuclear island infrastructures have been drawing extensive attention, and this paper aims to perform the safety assessment of Generation III nuclear power plant (NPP) buildings subjected to typical commercial aircrafts crash. At present Part I, finite element (FE) models establishment and validations for both the aircrafts and NPP buildings are performed. (i) Airbus A320 and A380 aircrafts are selected as the representative medium and large commercial aircrafts, and the corresponding fine FE models including the skin, beam, fuel and etc. are established. By comparing the numerically derived impact force time-histories with the existing published literatures, the rationality of aircrafts models is verified. (ii) Fine FE model of the Chinese Zhejiang Sanao NPP buildings is established, including the detailed structures and reinforcing arrangement of both the containment and auxiliary buildings. (iii) By numerically reproducing the existing 1/7.5 scaled aircraft model impact tests on steel plate reinforced concrete (SC) panels and assessing the impact process and velocity time-history of aircraft model, as well as the damage and the maximum deflection of SC panels, the applicability of the existing three concrete constitutive models (i.e., K&C, Winfrith and CSC) are evaluated and the superiority of Winfrith model for SC panels under deformable missile impact is verified. The present work can provide beneficial reference for the integral aircraft crash analyses and structural damage assessment in the following two parts of this paper.

• 한국구조물진단유지관리공학회 논문집
• /
• 제10권5호
• /
• pp.129-138
• /
• 2006

철근 선조립형 복합 데크플레이트는 거푸집 작업을 없앨 수 있기 때문에 건설현장에서의 발전을 가져왔다. 복합데크 시스템의 해석에는 2D해석법과 3D해석법이 있다. 지금까지 2D해석법을 사용하였으나, 선경축소에 따른 비렌딜 거동을 보다 정확히 표현할 수 있는 3D 해석법의 사용이 요구되어진다. 본 연구에서는 하부근의 선경축소, 아연도 강판의 유무, 경간, 슬래브 두께 등을 변수로 8개의 실험체를 제작하여 거동을 파악하였고, 2D해석법 및 3D해석법을 사용하여 결과를 비교 분석하였다. 2D해석법은 D10의 하부근을 사용하는 경우에만 적용하는 것이 타당하고, 비렌딜 거동을 포함한 상세한 거동을 표현하기 위해서는 3D해석법을 사용하는 것이 타당하다.

• 한국안전학회지
• /
• 제29권5호
• /
• pp.15-21
• /
• 2014

The aim of this work is conduct the study on light weight and structural performance improvement of the composite wind power blade. GFRP (Glass Fiber Reinforced Plastic) pre-empted by CFRP(Carbon Fiber Reinforced Plastic), the major material of wind power blade, was identified the superiority of mechanical performance through the tensile and fatigue test. SENT(Single Edge Notched Tension) specimen fracture test was conducted on the specimen that laminated together 2 ply CFRP with 4 ply GFRP through DIC(Digital Image Correlation) analysis. The SENT specimen thickness and $a_0/W$ ratio is 1.45 mm and 0.2, respectively. The fracture test accomplished with displacement control with 0.1 mm/min at the room temperature. The experimental apparatus used for the fracture test consisted of a 50kN universal dynamic tester and CCD camera connected to a personal computer (PC), which was used to record images of the specimen surface. Following data acquisition, the images and load-displacements were transferred to the PC, on which the DIC software was implement. The experiment and DIC analysis results show that CFRP/GFRP laminated composite exhibits improvement of the strength, compared with that of the existing blade material. This study shows the result that the strength of CFRP rotor blade of wind turbine satisfies through the experimental and DIC method.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2005년도 추계종합학술대회
• /
• pp.509-512
• /
• 2005

The aim of this work is to design a real-time reusable image enhancement architecture for video signals, based on a spatial processing of the video sequence. The VHDL hardware description language has been used in order to make possible a top-down design methodology. By adding proposed algorithms to the LPR(License Plate Recognition) system, the system is implemented with reliability and safety on a rainy day. Spartan-2E XC2s300E is used as implementation platforms for real-time system.