• 소성∙가공
• /
• 제19권4호
• /
• pp.236-241
• /
• 2010

The frictional behavior of bare steel sheet highly depends on surface roughness. It was investigated that the change of surface roughness of bare steel sheet due to deformation for each forming mode. The flat type friction test was done to check the effect of surface roughness change on frictional characteristics of bare steel sheet. As increasing the deformation, the Ra value was increased at stretching forming mode and drawing forming mode, however the change of Pc showed different trends. The Pc was decreased as increasing stretch deformation but increased at compression deformation. At drawing forming mode, the friction coefficient was increased as deformation was increased after initial big drop with drawing oil. As deformation was increased, the friction coefficient was decreased with drawing oil at stretching forming mode. The results show that the deformation changes the surface roughness and frictional characteristics of steel sheet but the effect depends on the forming mode.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1148-1153
• /
• 2004

Recently the high speed end-milling processing is demanded the high-precise technique with good surface rougj1ness and rapid time in aircraft, automobile part and molding industry. The working factors of high speed end-milling has an effect on surface roughness of cutting surface. Therefore this study was carried out to analyze the working factors to get the optimum surface roughness by design of experiment. From this study, surface roughness have an much effect according to priority on Spindle speed, feed rale, hardness and axial depth of cut By design of experiment, it is effectively represented shape characteristics of surface roughness in high speed end-milling And determination($R^2$) coefficient of regression equation had a satisfactory reliability of 89.7% and regression equation of surface roughness is made by regression analysis.

• 수산해양기술연구
• /
• 제48권3호
• /
• pp.277-283
• /
• 2012

The characteristics of abrasive wear on sliding speed of glass fiber reinforcement (GF/PUR) composites were investigated at ambient temperature by pin-on-disc friction test. The cumulative wear volume, friction coefficient and surface roughness of these materials on sliding speed were determined experimentally. The major failure mechanisms were lapping layers, deformation of resin, ploughing, delamination, and cracking by scanning electric microscopy (SEM) photograph of the tested surface. As increasing the sliding speed the GF/PUR composites indicated higher friction coefficient. The surface roughness of the GF/PUR composites was increased as the sliding speed was higher in wear test.

• Ocean and Polar Research
• /
• 제30권3호
• /
• pp.239-247
• /
• 2008

Spatial distribution of water flow generated by tidal current was investigated within a Zostera marina(seagrass) bed in Wonpo Bay. Water flow and elevation were observed during the seagrass growing season. The spatial distribution of water flow was numerically estimated using roughness coefficient. Water flow inside the seagrass meadow was compared with the observed values. Velocity in Zostera marina vegetated areas was approximately $25{\sim}84%$ lower than that of unvegetated areas. However, flow direction was the same. Intensity of the flood tide diminished appreciably within the seagrass bed, while its pattern was also affected. It is therefore concluded that water flow is influenced by Zostera marina meadows.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.155-156
• /
• 2002

During the sliding between a-CNx and $Si_3N_4$, applying nitrogen as environmental gas provided very low friction as the level of 0.01 in friction coefficient. In order to know the effect of the running-in process on the reduction of the friction, the effect of surface roughness of mating surface on friction was investigated. It was shown that smooth surface in wear scar of ball provided low friction coefficient. Friction coefficient after running-in was proportional to the Ry value of wear scar of ball. Also smooth thin transferred layer was observed on the wear scar of balls with an AFM after sliding test. Those results showed the smoothing of wear scar of ball, the generating of the transferred layer from CNx was necessary for low friction.

• 한국항해학회지
• /
• 제12권3호
• /
• pp.23-37
• /
• 1988

This paper deals with the method of determining the drag of hull surface which has any quality of roughness. The method consists mainly of the theoretical point of view, then the theory enables the drag coefficient to be calculated at full scale. The hydrodynamical roughness function of hull surface ${\triangle}U_+$, affected by the hull roughness are considered as to two cases, smooth surface and rough surface case separately. The inadequacy of a single parameter to define hull roughness is discussed and thus an as additional texture parameter is proposed.

• 한국수자원학회논문집
• /
• 제31권1호
• /
• pp.115-120
• /
• 1998

본 논문에서는 수심적분 2차원 모형을 하나 소개하고, 이 모형이 가질 수 있는 오차의 한계를 민감도분석을 통해 제시하였다. 민감도 분석 결과, Manning 조도계수, 혼합계수, 침강속도, 한계전단력 등이 부유사농도에 대해 모형에 미치는 영향은 매우 크게 나타났으며, 조위와 확산계수의 영향은 거의 없는 것으로 나타났다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.995-999
• /
• 2017

제어밸브의 유량계수에 영향을 미치는 인자들을 파악하고 그 영향을 분석하였다. 제어밸브의 유량계수는 레이놀즈 수, 연결 배관의 형상과 표면 조도 등에 영향을 받는다. 따라서 유량계수를 상수로 취급할 수 없다. 그러므로 로켓엔진과 같이 정확한 유량계수를 요구하는 시스템에서 사용할 목적으로 제어밸브의 유량계수를 측정할 때는 실제 사용 환경과 유사한 레이놀즈 수 영역에서, 동일한 조도 및 형상을 가지는 입출구 배관을 사용하여 측정해야 한다.

• 한국전자파학회논문지
• /
• 제17권12호
• /
• pp.1181-1188
• /
• 2006

본 논문에서는 토양 표면의 레이더 후방 산란 계수와 표면 거칠기의 관계를 계산해 보고, 측정 길이에 따른 표면 거칠기 변화를 알아본 후에, 측정 길이에 따른 표면 거칠기와 레이더 후방 산란 계수의 관계를 보여준다. 이 연구 결과에 따르면, 측정 길이가 짧아져서 표면 거칠기 값의 변화가 심하다하더라도 계산된 레이더 후방 산란 계수에는 적은 영향밖에 주지 않는다는 것을 보여준다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제23권1호
• /
• pp.54-61
• /
• 1999

The fully developed turbulent momentum and heat transfer induced by the roughness elements on the outer wall surfaces in concentric annuli are analytically studied on the basis of a modified turbu-lence model. The resulting momentum and heat transfer are discussed in terms of various parame-ters such as the radius ratio the roughness density Reynolds number and Prandtl number accord-ing to the heating condition. The study shows that certain artificial roughness elements may be used to enhance heat transfer rates with advantage from the overall efficiency point of view.