• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.05a
• /
• pp.215-219
• /
• 2002

In this study, we show the numerical and the experimental results for fluid motions inside a rectangular container subjected to a background rotation added by a rotational oscillation. In the numerical computation, we used a parallel computer system of PC-cluster type. Attention is given to dependence of the flow patterns on the parameter change. It shows that the flow becomes in a periodic state at low Reynolds numbers and undergoes a transition to a chaotic motion at high Reynolds numbers. It also shows that the fluid motion tends to be depth-independent at ${\epsilon}$ up to 0.3 for Re lower than 5235.

• Journal of Information Display
• /
• v.12 no.3
• /
• pp.135-139
• /
• 2011

This paper presents the directly obtained rotational viscosity values of E7, which includes pentylcyanobiphenol, heptylcyanobiphenol, 4-cyano-4'-n-octyloxy-1,1'-biphenyl, and 4-cyano-4"-n-pentyl-1,1',1"-terphenyl, at various tempe using molecular dynamics computer simulation. The director mean squared displacement was achieved from the squared displacement of the mean director using the concept of the mean director of various nematic liquid crystals. The calculated values were compared with the experiment results that predicted a good agreement. Additional points that must be considered for further study are also discussed.

• Journal of computational fluids engineering
• /
• v.16 no.1
• /
• pp.90-95
• /
• 2011

The Navier-Stokes equations are solved to study the flow characteristics of a micro viscous pump. The viscous micropump is consisted of a stationary disk with a spiral shaped channel and a rotating disk. A simple geometrical model for the tip clearance is proposed and validated by comparing computed flow rate with corresponding experimental data. Present numerical solutions show satisfactory agreement with the corresponding experimental data. The tip clearance effect is found to become significant as the rotational speed increases. As the pressure load increases, a reversed flow region is seen to form near the stationary disk. The height of the channel is shown to be optimized in terms of the flow rate for a given rotational speed and pressure load. The optimal height of the channel becomes small as the rotational speed decreases or the pressure load increases. The flow rate of the pump is found to be in proportion to the width of channel.

• Proceedings of the KIEE Conference
• /
• 2003.10a
• /
• pp.42-44
• /
• 2003

The paper presents the method and apparatus for conformal photoresist spray coating on the 3D structured substrate. The system consists of a high-temperature-rotational chuck, ultrasonic spray nozzle module, angle control module and nozzle moving module. The coating uniformity is acquired by controlling the moving speed of the ultrasonic spray nozzle across the substrate which is rotated constantly. To coat the photoresist conformally the spray angle of the nozzle and the temperature of the substrate are controlled during spray coating. The rotational chuck can be heated up by hot air or $N_2$. The photoresist (AZ1512) has been coated on the 3D structured wafer by spray coating system and the characteristics have been evaluated.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.10
• /
• pp.1895-1902
• /
• 2011

This work was carried out for the measurement of vibration and rotation temperature using the optical emission spectroscopy of nitrogen second positive system in the small plasma torch. Among emissions $N_2$ SP systems, the emission of $N_2$ SP(0-0) was so strong. Emission peaks of SP system increased until the position of 12.5[mm] from the end of plasma torch, after that it decreased. However, vibration temperature decreased from 1540[K] to 1000[K] at the position of 12.5[mm]. In addition, rotational temperature was about 400[K] at the position of 10[mm] and it increased a little as much of 420[K] at 12.5[mm]. Consequently, the plasma torch discussed in this work is possible to apply in the surface treatment process under the low temperature.

• Journal of Advanced Marine Engineering and Technology
• /
• v.15 no.1
• /
• pp.59-70
• /
• 1991

Rupture of lubricant film, thermal characteristics, and variation of viscosity are very important factors to evaluate the performance of journal bearing. Variation of external conditions, load or rotational speed, largely influence these facters. For example, if rotational speed increases lubricant bulk temperature increases and viscosity drops. In this paper the effect of rotational speed variation on the characteristics of lubricant film in a journal bearing is investigated by experiment and theoretical analysis. It has been measured number of lubricant film rupture and lubricant bulk temperature form journal bearing which have been established at the various operating speed of shaft. The range of speed variation is from 900rpm to 2100rpm. Theoretical analysis has been carried out for rupture of lubricant film and thermal characteristics, and these results are compared with experimental results.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.1
• /
• pp.28-34
• /
• 1999

According to the development of tool material and the improvement of machinability of cutting material like aluminium alloy, the higher spindle speed is needed. However, the higher speed causes the heat generation of bearings, the deformation of spindle unit parts, and the rotational accuracy of spindle to be worse. Therefore, it is essential to analyze and control the heat generation and the thermal behavior of spindle unit in order to have higher speed and better rotational accuracy. This paper shows the analogy between the analyzation of heat generation and thermal behavior of high speed spindle system by finite element method and the test results of actual temperature rise through running test, and shows the necessity of cooling the spindle and inner ring side of bearings for the thermal balance of high speed spindle system.

• Journal of the korean Society of Automotive Engineers
• /
• v.11 no.5
• /
• pp.76-89
• /
• 1989

With the objective of studying the response of brain tissue in a transient rotational acceleration of the head, as occurs in car crash, the problem of a cylindrical case containing a prototype brain material of silicone gel and subjected to a rotational acceleration around the axis of the cylinder is analysed. The prototype material is considered to be homogeneous and isotropic, and is modeled alternatively as a linear elastic or a linear viscoelastic solid. The computational model for the present problem consists of a 3-dimensional isoparametric finite element model, wherein large deformations and large strains are treated through the updated Lagrangian approach. A comparison of the results of the present 3-dimensional computations, with the attendant assumptions on material data, is made with the results of independent experimental study. The deformation profiles and the major characteristics of response of the brain material are in good agreement with the test results. Moreover, the study suggests the possibility that the use of more accurate material data may yield very useful results even appropriate for accurate quantification of deformations.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.1 no.1
• /
• pp.101-109
• /
• 1993

Dynamic characteristics of an electro-magnetic clutch transmission system were investigated by using Bondgraph modeling method. Simulation results showed that when the rotor engaged with the armature, the response time of the current, the driver torque, the rotational speed and the relative sliding time between the driver and the driven side decreased, as the gap size between the rotor and the armature decreased and the number of coil turns increased. Also, when the rotor disengaged with the armature, the delay time increased with the decreased gap size and the increased number of coil turns. It was found that the experimental results of the current, the driver torque, the rotational speeds were in good accordance with the theoretical results. The results of this study can be used as basic design materials of the electro-magnetic clutch.

• Structural Engineering and Mechanics
• /
• v.13 no.1
• /
• pp.1-16
• /
• 2002

This paper presents the findings of an investigation carried out to determine the most appropriate connections, in terms of rotational stiffness, to use for the optimum design of cold-formed Zed section sleeve joint purlin system. Experiments and parametric studies were conducted to investigate the effects of geometric variables on the behavior of the sleeve-purlin and cleat-purlin connections of the sleeve joint purlin system. The variables considered were purlin size and thickness, sleeve size, thickness, length and bolt position. The test results were used to verify the empirical expressions, developed herein, employed to determine the rotational stiffness of connections. With the predicted connection stiffness, the most suitable sleeve-purlin and cleat-purlin connections can be selected so as to produce an optimum condition for the sleeve joint purlin system.