• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.2135-2137
• /
• 2000

Usually arc phenomena are not easily characterized due to unstable behavior very short existence-times, high temperature and the required isolation of measurement instruments. This paper presents some arc-behaviors in a rotary arc gap-switch(RAG) using a 500kJ capacitor bank. It includes the speed variations of the rotating arc, the impacts of the oscillating current on the arc initiations and re-ignitions. Changes in the arc-dimension with respect to time and current magnitudes are also analyzed.

• 한국추진공학회지
• /
• 제25권1호
• /
• pp.19-28
• /
• 2021

회전 데토네이션 엔진(Rotating Detonation Engine, RDE)은 기계 장치나 유동이 아닌 데토네이션 파만이 연소실 벽을 따라 회전한다. 따라서 RDE 단면이 원형이어야 할 필요가 없으며 임의 단면의 닫힌 형상이 가능하다. 본 연구에서는 임의의 단면을 가지는 RDE의 한 가지 예로써 tri-arc 단면 형상의 RDE를 설계하였으며, 실험적으로 작동 및 성능 특성을 살펴보았다. 동압 센서와 고속카메라를 통하여 데토네이션 파의 회전을 확인하였으며, 오목 면과 볼록 면에서 질량 유량에 따른 데토네이션파의 특징을 알아보았다. 본 연구에서는 유량 조건에 따라 17.0 N에서 96.0 N의 추력 수준을 얻을 수 있었다.

• 동력기계공학회지
• /
• 제6권4호
• /
• pp.43-48
• /
• 2002

This paper presents a seam tracking controller of high speed rotating arc sensor developed by microprocessor based system. The seam tracking algorithm is based on the average current value at each interval region of four phase points on one rotating cycle. To remove the noise effect for the measured current, the area during one rotating cycle is separated into four regions of front, rear, left and right. The average values at each region are calculated, using the regional current values and a low pass filter incorporating the moving average and exponential smoothing methods is adopted. The effectiveness is proven through the experimental results for several kinds of welding condition.

• International Journal of Precision Engineering and Manufacturing
• /
• 제4권6호
• /
• pp.20-28
• /
• 2003

This paper presents development of a high speed rotating arc sensor system using a microprocessor based controller with tracking function for a complicate curved fillet welding line, The welding tip connected to the torch body is eccentrically positioned from the centerline of the torch, The area during one rotating cycle is divided into 4 regions of front, rear, right and left in welding direction of the torch tip to determine the horizontal deviation between the welding seam and the torch position. The average value at each region is calculated using the regional current values and a low pass filter incorporated with the moving average method is implemented. The effectiveness of the developed system is proven through the experimental results for several kinds of complicate curved fillet welding lines.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1997년도 특별강연 및 춘계학술발표 개요집
• /
• pp.129-132
• /
• 1997

• Journal of Welding and Joining
• /
• 제21권3호
• /
• pp.46-50
• /
• 2003

The horizontal fillet joint is one of the most important weld joints in the shipbuilding industry. High-speed rotating arc welding, which can increase the leg length, is an effective way to improve the weld productivity and quality for the horizontal fillet welding. Based on the Taguchi method, the effects of welding parameters on bead characteristics - leg length, asymmetry, undercut, overlap - are investigated fur high-speed welding process. As a result, the adequate welding parameters are selected for the required leg length, symmetric bead and no undercut. Besides, considerably consistent leg length is observed for the horizontal fillet welding with gap variation up to 3mm.

• 한국연소학회지
• /
• 제22권1호
• /
• pp.23-31
• /
• 2017

Large-scale fuel tanks emit massive amount of hardly-combustible VOC mixtures which are light hydrocarbon species in dilution with nitrogen and carbon dioxide. We have developed a lab-scale burner to combust those VOC mixtures by use of a turbulent partially-premixed flame as a pilot flame. For a higher HC treatment ratio, the mixture gases were reformed by a rotating arc plasma device. The results showed that the nitrogen mole fraction and the injecting speed of the VOC mixture influence on the performance of the burner. It was also found that the size of the pilot flame and the power supplied to the plasma device determine the overall HC treatment ratio and the concentrations of CO and NOx in the exhaust gas.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.94.1-94
• /
• 2001

Arc sensor gives important groove information during welding. Automatic seam tracking control system with arc sensor has significant characteristics such that bead formation is given as decentralization of penetration and formation of concave bead profile and that a turning point of transverse weaving with constant arc length control is decided whether or not torch height reaches to a specified setting level. Furthermore, the rotating action of the arc prevents hanging of weld bead and forms flat bead surface under high speed welding condition. The variation of groove and deposition area can be detected from the trace of weaving. The area and width of weaving trace has close correlation with the area of groove and deposition. In this paper, main object of this system is to realize an adaptive microprocessor based controller ...

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.700-705
• /
• 2001

The paper presents a seam tracking controller of high speed rotating arc sensor developed by microprocessor based system. The seam tracking algorithm is based on the average current value at each interval region of four phase points on one rotating cycle. To remove the noise effect for the measured current, the area during one rotating cycle is separated into four regions of front, rear, left and right. The average values at each region are calculated, using the regional current values and a low pass filter incorporating the moving average and exponential smoothing methods is adopted.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2001년도 춘계학술발표대회 개요집
• /
• pp.27-30
• /
• 2001