• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.2
• /
• pp.300-307
• /
• 2002

Partial penetration welding joint is defined as groove welds welded from one side, without steel backing or groove welds welded from both sides but without back gouging. So it has an unwelded portion at the root of the weld. Study of partial penetration weldment fracture behavior includes residual stress analysis and fracture analysis. The J-integral loses its path independency in residual stress field. Therefore, it is necessary to introduce a new J-integral, J, which is defined including the effect of plastic deformation and thermal strain. In this study, theoretical formulation and program were developed for the evaluation of J-integral for the crack tip located in the weldment. Evaluations of fracture behavior were performed for partial penetration multi-pass weldment of 25.4mm thick plate by J-integral. From a point of fracture in partial penetration multi-pass welding, it seemed to be better to control root face smaller than 6.35mm.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.11
• /
• pp.1813-1819
• /
• 2001

Partial penetration welding Joint defines that groove welds without steel backing, welded from on side, and groove weeds welded from both sides but without back gouging, that is. it has an unwelded portion at the root of the weld. In this study we analysed fur residual stress and displacement distribution on partial penetration welding condition of thick plate metal. For 25.4mm thick plate, theoretical residual stress and displacement analysis by finite element method using ABAQUS was carried out and compared with the experimental result using hole-drilling method. In results of the condition of partial penetration, it appeared that longitudinal stress at welding area was a little difference and transverse stress did not have any effect by partial penetration multi-pass welding. From a point of welding distortion in partial penetration multi-pass welding, it seemed to be better to control root face smaller than 6.35mm.

• Plant Resources
• /
• v.3 no.3
• /
• pp.200-205
• /
• 2000

This study selects Sunwol local group, Gusang local group and Yongjun local group to examine the appropriate amount of applied fertilizer in cultivating the double crop seed of Alisma plantago by transplantation in the southern area, improve and complements the double cropping techniques and contribute to stable production. While the plant height is 45,47 and 49cm and the number of leaves is 11.7, 12.5 and 14.4 at non-fertilizing plot, the plant height is 67, 72 and 75cm and the number of leaves is 15.8, 17.2 and 19.3 at all fertilizing plot and their growth is active and in the character of plant height and the number of leaves, especially in the groove of N-P$_{2}$O$_{5}$-K$_{2}$O= 30-15-45kg/10a, the mean plant height of Sunwol is 75cm and mean number of its leaves is 19.3, the mean plant height and number of leaves in Gusang are 72cm and 17.2 respectively and those of Yongjun are 67cm and 15.8 respectively. While the number of floral axis is 1,2 in non-fertilizing plot, that of the whole varieties in all fertilizing plot is 3, 4, 5 and the mean floral axis of Sunwol is N-P$_{2}$O$_{5}$-K$_{2}$O = 10-5-15, 20-10-30, 30-15-45 kg/10a and 18-0-18 of complex fertilizer and 21-17-17kg/10a and it is small in all fertilizing plot. The yield of dry root per 10a is high in all fertilizing grooves and especially in the groove of N-P$_{2}$O$_{5}$-K$_{2}$O = 30-15-45 kg/10a, it is 372.6kg, in the groove of 18-0-18kg/10a using complex fertilizer, it is 389.1kg and in that of 21-17-17kg/10a, it is 376.7kg.6.7kg.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2007.09a
• /
• pp.135-141
• /
• 2007

CSR(Common Structure Rules) enter into force on $1^{st}$ April 2006. Generally for double hull tankers of less than 150m in length, the Rules of the individual Classification Society are to be applied. Where high tensile stresses act through an intermediate plate, increased fillet welds or penetration welds are to be used longitudinal/transverse bulkhead primary support member end connections to the double bottom. If workers have begun to make used of established procedures between corrugated BHD and lower stool joint, first to welding on groove of face and then it has to gouging to blow on groove of root. So amount of man-hour increased, productivity secreased.

• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.138-140
• /
• 2005

Plasma arc welding(PAW) technology is a proven process that has already been adopted by other industrial fields and recently has been considered to join the tank structure of LNG carrier. The purpose of this study is to introduce PAW process for the root welding of stainless steel pipes instead of TIG welding. There are distinctive features of the PAW compared to TIG welding; higher energy density that can increase welding speed by more than twofold, and longer arc length that can be controlled to trace seam line easily because of allowable gap between workpiece and torch. However, PAW process is also very sensitive to the root gap and misalignment due to the characteristics of long and narrow arc shape. So, we have done various experiments to establish the allowable fit-up condition by changing welding parameters including arc length, with or without filler metal, groove shape, and obtained satisfactory result.

• Restorative Dentistry and Endodontics
• /
• v.6 no.1
• /
• pp.105-107
• /
• 1980

A total of 125 extracted maxillary first molars were used to study the configuration of the floor of the pulp chamber. The specimens were ground and the pulp chamber was examined with a magnifying glass and explored with sharp explorer. The study showed the shape of the pulp chamber, number of root canals, and type of canal orifice. The results were as follows; 1. In so far as observing the shape of the pulp chamber of the teeth, 50.4% of the teeth were trapezoid, 20.8% were inverted trapezoid, 18.4% were rectangle and 10.4% were triangle shape. 2. 71.2% of the specimens have 3 root canal orifices, and 28.8% have 4 root canal orifices. 3. 71.2% of the specimens have 1 mesiobuccal canal orifice, 23.2% have 2 mesio-buccal canal orifices joined by a groove, and 5.6% have 2 mesio-buccal canal orifices seperated each other.

• Restorative Dentistry and Endodontics
• /
• v.27 no.4
• /
• pp.421-431
• /
• 2002

C-shaped canal configuration is very difficult to treat because that clues about preoperative canal anatomy cannot be ascertained from clinical crown morphology and limited information can be derived from radiographic examination. This study was done to get more informations about the root and canal configuration of C-shape root by 3-dimensionally reconstructing for the purpose of enhancing success rate of endodontic treatment. 30 mandibular molars with C-shaped root were selected. Six photo images from occlusal, apical, mesial, distal, buccal, lingual directions and radiographic view were taken as preoperative ones to compare them with 3-D image. After crown reduction to the level of 1-2mm over pulpal floor was performed, teeth were stored in 5.25% sodium hypochlorite solution for the removal of pulp tissue and debris. They were cleaned under running water, allowed to bench dry and embedded in a self-curing resin. This resin block was serially ground with a microtome (Accutom-50, Struers, Denmark) and the image of each level was recorded by digital camera (FinePix S1-pro, Fuji Co., Japan). The thickness of each section was 0.25mm. Photographs of serial sections through all root canal were digitized using Adobe Photoshop 5.0 and then minimum thickness of open and closed sites were measured (open site is the surface containing occluso-apical groove closed site is oppsite). After dizitization using 3-D Doctor (Able software Corp, USA). 3D reconstruction of the outer surface of tooth and the inner surface of pulp space was made. Canal classsification of C-shaped roots was performed from this 3-D reconstructed image. The results were as follows : 1. Most C-shape rooted teeth showed lingual groove (28/30). 2 According to Vertuccis' calssification, type I, II, III, IV, VII were observed. but also new canal types suck as 2-3-2, 1-2-3-2. 2-3-2-1, 2-3-2-3 were shown. 3 There was little difference in minimum thickness on coronal and apical portions, but open site were thinner than closed site on mid portion. Conclusively, 3D reconstruction method could make the exact configurations of C-shape root possible to be visualized and analyzed from multi-directions. Data from minimum thickness recommend cleaning and shaping be more carefully done on dangerous mid portion.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.33 no.2
• /
• pp.97-105
• /
• 2017

Purpose: The purpose of this study was comparing the efficacy of passive irrigation (PI) and passive ultrasonic irrigation (PUI) for ability to remove debriment of canals. Materials and Methods: Mandibular premolars were decoronated and standardized to 16 mm length. After root canal enlargement and half separating longitudinally, standardized groove of 4 mm length, 0.2 mm width and 0.5 mm depth were formed on the dentin wall of one half. Three depressions in the canal wall of the opposite half, 0.3 mm in diameter and 0.5 mm in depth, were formed. After each groove and depression was filled with dentin debris, two sections of each half were reassembled using impression putty material. In group 1 the canals were irrigated with 2.5% NaOCl by PI. In group 2 the canals were irrigated with 2.5% NaOCl by PUI. Before and after root canal irrigation, the root canal wall of the section was taken with a microscope and a digital camera as images. The amount of dentin debris remaining in grooves and depressions was assessed using a scoring system. Results: There was no significant difference between PI and PUI except for the middle 1/3 of the root canal (P = 0.004). Conclusion: At the middle 1/3 of the root canal, PUI removed more dentine debris than PI. But the removal efficiency of dentin debris is not significantly different between the PUI and PI at the apical area of root canal in mandibular premolars.

• Restorative Dentistry and Endodontics
• /
• v.40 no.2
• /
• pp.161-165
• /
• 2015

Three-dimensional (3D) reconstruction of cone-beam computed tomography (CBCT) scans appears to be a valuable method for assessing pulp canal configuration. The aim of this report is to describe endodontic treatment of a mandibular second premolar with aberrant pulp canal morphology detected by CBCT and confirmed by 3D modeling. An accessory canal was suspected during endodontic treatment of the mandibular left second premolar in a 21 year old woman with a chief complaint of pulsating pain. Axial cross-sectional CBCT scans revealed that the pulp canal divided into mesiobuccal, lingual, and buccal canals in the middle third and ended as four separate foramina. 3D modeling confirmed the anomalous configuration of the fused root with a deep lingual groove. Endodontic treatment of the tooth was completed in two appointments. The root canals were obturated using lateral compaction of gutta-percha and root canal sealer. The tooth remained asymptomatic and did not develop periapical pathology until 12 months postoperatively. CBCT and 3D modeling enable preoperative evaluation of aberrant root canal systems and facilitate endodontic treatment.

• Journal of Welding and Joining
• /
• v.27 no.1
• /
• pp.95-101
• /
• 2009

In case of manufacturing the high quality welds or pipeline, the full penetration weld has to be made along the weld joint. Thus the root pass welding is very important and has to be selected carefully. In this study, an experimental method for the selection of optimal welding condition was proposed in the root pass welding which was done along the V-grooved butt weld joint. This method uses the response surface analysis in which the width and height of back bead were chosen as the quality variables of the weld. The overall desirability function, which is the combined desirability function for the two quality variables, was used as the objective function for getting the optimal welding condition. In the experiments, the target values of the back bead width and the height are 6mm and zero respectively for the V-grooved butt weld joint of 8mm thickness mild steel. The optimal welding conditions could predict the back bead profile(bead width and height) as 6.003mm and -0.003mm. From a series of welding test, it was revealed that a uniform and full penetration weld bead can be obtained by adopting the optimal welding condition which was determined according to the method proposed.