• Journal of the Korean Chemical Society
• /
• v.26 no.5
• /
• pp.282-290
• /
• 1982

Several cation exchanged-layer silicate catalysts were prepared from acid clay mainly consisted of montmorillonite, and their catalytic activities for the ethylene polymerization were studied at room temperature. It was found that over$Ni^{2+}$ -Mont, dimerization of ethylene to n-butene proceeded selectively.$Ni^{2+}$ -Mont was activated by evacuation at elevated temperature, giving a maximum temperature, 150$^{\circ}$C . The variations in catalytic activities were closely correlated to the acidity of the catalysts.$Cr^{3+}$ -Mont exhibited a high activity for the polymerization, showing, a maximum at the evacuation temperature of 450$^{\circ}C$. The active site in $Cr^{3+}$-Mont was considered to be $Cr^{3+}$ ion.

• Journal of the Korean Chemical Society
• /
• v.58 no.5
• /
• pp.456-462
• /
• 2014

Binary-doped conducting chiral polyaniline (PAni) was synthesized by electrochemical polymerization of aniline at low-temperature ($0^{\circ}C$) and room-temperature (RT) conditions. (+)-Camphorsulfonic acid (CSA) and hydrochloric acid (HCl) were used as a binary dopant. Formation of the binary-doped PAni rather than a mixture of the corresponding single-doped PAni was confirmed by cyclic voltammogram, FT-IR and circular dichroism spectra. The temperature influenced the electrochemical behavior and doping level, thus determining the crystallinity and morphology of the PAni. However, among other results, morphology of the PAni is found to be most strongly depends on the polymerization temperature. With increased temperature from the initial state to RT, morphology of the PAni changed from fibrous to short-fibrous structure. The sheet resistance of the PAni films on an ITO was measured by using four-point probe dc method.

• Proceedings of the Korean Fiber Society Conference
• /
• 1990.06b
• /
• pp.8-8
• /
• 1990

A new method for the graft polymerization of acrylonitrile onto starch is presented. Graft polymerization of acrylonitrile onto starch and the subsequent hydrolysis in sodium hydroxide solution to prepare absorbents is well known. This process has been utilized to produce the commercial product, Super Slurper. In a typical batch process, ~5% starch in water mixture is gelatinized at $95^{\circ}C$ under stirring for 1 hour then cooled to room temperature. The graft polymerization itself is carried out for approximately 2 hours at $25~30^{\circ}C$ on the gelatinized starch by eerie ion initiation. In this study, graft polymerization of acrylonitrile onto starch via a reactive extrusion process which is a continuous, efficient process is described. Initial concentration of starch in water is 35% and the reaction temperatures are between $50~80^{\circ}C$. However, the most significant difference in the reactive extrusion process is the short time in which the graft polymerization takes place. Preliminary results on the properties of graft polymerization products obtained from the reactive extrusion process are compared to those obtained from the batch process as well as the absorbency of the hydrolyzed samples. Absorbent material has also been prepared by sequential grafting and saponification in the extruder followed by a 2 hour heat treatment of the extrudate in an air circulated oven at $100^{\circ}C$.

• Carbon letters
• /
• v.11 no.3
• /
• pp.216-223
• /
• 2010

Two-types of ionically modified multi-walled carbon nanotube (MWNTs) based sensors were developed by radiationinduced graft polymerization using vinyl monomers such as 3-(butyl imidazol)-2-(hydroxyl)propyl methyl methacrylate and 1-[(4-ethenylphenyl)methyl]-3-buthyl-imidazolium chloride with ionic properties, in aqueous solution at room temperature. Subsequently, the tyrosinase-immobilized biosensor was fabricated by a hand-casting of the ionic property-modified MWNTs, tyrosinase, and chitosan solution as a binder onto ITO glass surface. The sensing ranges of the tyrosinase-biosensor for phenol in phosphate buffer solution was in the range of 0.005~0.2 mM. The total phenolic compounds mainly such as caffeine of the tyrosinase-immobilized biosensor for commercial coffee were also determined.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.7
• /
• pp.2345-2351
• /
• 2012

Conductive honeycomb-patterned polystyrene (PS) thin films were prepared by the formation of a polyaniline (PANI) thin layer on the surface of the patterned PS thin films using simple one-step chemical oxidative polymerization of aniline. The in situ chemical oxidation polymerization of aniline hydrochloride solution on the patterned structure of the PS films was conducted in the presence of multiwalled carbon nanotubes (MWCNT) to prepare the PANI-MWCNT/PS composite film. The concentration (wt %) of MWCNT was varied in the range of 1%-3% by weight. The dependence of surface morphology of the PANI/PS and PANI-MWCNT/PS composite film to the polymerization time was observed by scanning electron microscopy. The room temperature DC conductivity was obtained by the four-probe technique. The conductivity of the PANI-MWCNT/PS composite film was affected both by the MWCNT concentration and polymerization time. In addition, DC electrical field was loaded during the oxidative polymerization to affect the distribution of the MWCNT included in the composite film, varying the loading voltage in the range of 0.1-3.0 V. The conductivity of the PANI-MWCNT/PS composite film was increased as loading voltage rose. However, this increase stops at a voltage higher than the critical value.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 2000.06a
• /
• pp.151-163
• /
• 2000

A polymerized organic-inorganic complexation route is introduced for the synthesis of oxide ceramic powders. Polyvinyl alcohol was used as the organic carrier for precursor ceramic gel. Porous and soft powders, which have a high specific surface area, were obtained after calcinating the aerated precursors. The PVA content and its degree of polymerization had a significant influence on the homogeneity of the final powder. In particular, attrition milling process with the porous powder resulted in ultra-fine particles. In the case of the preparation of cordierite powder, nano-size powder, which has a high specific surface area of 181 ㎡/g, was obtained by the milling process. The complexation route was also applied to the synthesis of unstable phase in room temperature like beta-cristobalite, high temperature form of silica.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.05a
• /
• pp.273-276
• /
• 1996

Polyphenylenediamine(PPD) film was prepared with dimethylsulfoxide after the synthesis of PPD by chemical polymerization. The molecular structure of conductive polymer synthesized were discussed by using SEM, FT-IR, NMR. The electrical conductivity measurements were carried out at room temperature. The electrical conductivity which was obtained from electrical instrument was 1.98${\times}$10$\^$-2/ S/cm at ambient temperature.

• Journal of Technologic Dentistry
• /
• v.12 no.1
• /
• pp.103-106
• /
• 1990

The purpose of this study was to determine if homogeneity of the resin associated with benchcuring could be obtained in the curing unit as the water increased from room temperature to curing temperature. The results of the experiment were as follows : 1. Long periods of bench-curing are not necessary. 2. Bench-curing can take place in the water bath of the curing unit. When this procedure is used, the water should be far enough below the temerature at which active polymerization of the resin proceeds to allow the bench-curing to occur.

• Polymer(Korea)
• /
• v.28 no.4
• /
• pp.344-351
• /
• 2004

Poly(ethylene glycol)-based diblock and triblock polyester copolymers stimulating to temperature were studied as injectable biomaterials in drug delivery system because of their nontoxicity, biocompatibility and biodegradability. We synthesized the diblock copolymers consisting of methoxy poly(ethylene glycol) (MPEG) (M$_{n}$=750 g/mole) and poly($\varepsilon$-caprolactone) (PCL) by ring opening polymerization of $\varepsilon$-CL with MPEG as an initiator in the presence of HCl . Et$_2$O. The aqueous solution of synthesized diblock copolymers represented sol phase at room temperature and a sol to gel phase transition as the temperature increased from room temperature to body temperature. To confirm the in vivo gel formation, we observed the formation of gel in the mice body after injection of 20 wt% aqueous solution of each block copolymer. After 2 months, we observed the maintenance of gel without dispersion in mice. In this study, we synthesized diblock copolymers exhibiting sol-gel phase transition and confirmed the feasibility as biomaterials of injectable implantation.n.

• Macromolecular Research
• /
• v.11 no.6
• /
• pp.481-487
• /
• 2003

Polypyrrole (PPy) was coated sequentially by chemical and electrochemical methods on a woven fabric, giving rise to a fabric having high electrical conductivity. We investigated the effects of the preparation conditions on the various properties of the resulting fabric. The PPy-coated fabric with optimum properties was obtained when it was prepared sequentially by chemical polymerization at the elevated temperature of 100$^{\circ}C$ under a pressure of 0.9 kgf/$\textrm{cm}^2$ and then electrochemical polymerization with a 3.06 mA/$\textrm{cm}^2$ current density at 25 $^{\circ}C$ for 2 hrs with the separator plate. The surface resistivity of the resulting fabric was as low as 5 Ω/$\square$ .The PPy-coated fabric prepared under the optimum conditions showed practically applicable heat generating property. When electrical power was supplied to the fabric using a commercial battery for a mobile phone (3.6 V, LGLl-AHM), the temperature of the fabric increased very quickly from room temperature to ca. 55 $^{\circ}C$ within 2 min and was maintained for ca. 80 min at that temperature. The heat generating property of the fabric was extremely stable, exhibiting similar behavior over 10 repeated cycles. Therefore, we suggest that the PPy-coated fabric in this study may be practically useful for many applications, including flexible, portable surface-heating elements for medical or other applications.