• Journal of the Korean Wood Science and Technology
• /
• 제49권4호
• /
• pp.336-359
• /
• 2021

본 연구는 고층 목조건축에 사용되는 대형 목재 패널인 CLT의 낮은 rolling shear strength를 개선하기 위해 hybrid CLT의 연구 개발 동향을 분석하였다. 이를 통해 CLT의 국산화를 위한 연구개발 방향에 활용 가능한 기초자료를 마련하고자 하였고, 낮은 rolling shear strength를 향상시키기 위한 방안으로 활엽수 층재 사용, 층재 배열 각도 변화, 구조용 목질복합체의 사용이 주를 이루고 있다. 활엽수 층재는 침엽수 보다 rolling shear strength와 shear modulus 모두 2배 이상의 높은 값을 나타내므로 활엽수 층재 사용 및 미이용 수종의 활용이 가능함을 확인하였다. 층재 배열 각도 변화에 따라 rolling shear stength 1.5배, shear modulus 8.3배, bending stiffness 4.1배 향상되어 층재 배열 각도를 감소시킴으로써 CLT 강도 향상을 확인하였다. 구조용 목질재료는 기존에 강도성능이 확보된 재료로 층재로 사용하였을 때 최대 MOR 1.35배, MOE 1.5배, rolling shear strength 2배 향상되었고, 층재 간의 접착강도 또한 집성재 블록전단강도 기준인 7.0 N/mm²을 확보할 수 있었다. 선행연구결과를 통해 MOE 7.0 GPa, MOR 40.0 MPa 이상의 휨 특성을 가진 구조용 목질재료를 사용하였을 때 강도성능이 향상됨을 확인하였다. 이를 통해 구조용 목질재료 층재 강도 기준으로 판단하였다. rolling shear strength 개선하기 위한 최적의 방법은 기존 규격에 의한 강도값을 가진 구조용 목질재료의 적용이 가장 유리할 것으로 판단하나, 구조용 목질재료의 섬유 배열에 따른 CLT 층재 배열 방향, 층재 간 접착 강도 등에 대한 추가적인 연구가 필요하다.

• Journal of the Korean Wood Science and Technology
• /
• 제46권5호
• /
• pp.425-436
• /
• 2018

본 연구는 ASTM D2718의 5점 휨하중 시험법을 사용하여 OSB(oriented strand board)와 국산합판의 굴림전단성능을 평가하기 위하여 수행되었다. 각 시험용 판넬에 대해 길이방향에 평행한 것과 수직인 시험편을 제작하여 각각 시험하였으며, 파괴양상을 관찰하였다. 시험 결과 굴림전단력은 강축방향에 평행한 경우 $1.32-1.938N/mm^2$, 강축방향에 수직인 경우 $1.46-1.99N/mm^2$ 정도로 나타났으며 방향에 따른 차이는 크게 나타나지 않았다. 국산합판은 길이방향에 평행한 경우는 캐나다산 OSB와, 수직인 경우는 칠레산 OSB와 통계적으로 차이가 나타나지 않았다. 파괴는 OSB에서는 모두 전단에 의한 파괴가 나타났으며, 합판의 경우에는 전단, 접착층의 박리, 휨과 전단에 의한 복합파괴가 관찰되었다.

• Journal of Welding and Joining
• /
• 제8권2호
• /
• pp.70-79
• /
• 1990

Stainless clad steels were made through hot rolling process. Backing plates employed in this study were HSLA steel and mild steel. The shear bond strength increased with an increase of the soaking temperature and time. It was also found that the shear bond strength increased with an increase of the reduction ratio. The threshold deformation was observed to be 20% and 10% respectively when the soaking conditions of 15 min. at 900.deg. C and 30 min. at 1000.deg. C were applied. Either the rolling or the transverse direction did not give any significant difference in the shear bond strength. Stainless steel-HSLA steel was superior to stainless steel-mild steel in the same range of magnitude. Because the above experimental results were in contrary to the existing mechanisms, the new model was proposed to describe the bonding mechanism and the void formation.

• Journal of the Korean Wood Science and Technology
• /
• 제48권6호
• /
• pp.791-806
• /
• 2020

본 연구에서는 공학목재로 목구조건축에 주로 사용되는 집성재 및 CLT 그리고 Ply-lam CLT의 블록전단시험을 실시하여 강도 및 파괴 유형을 비교 분석하였다. 이를 통해 Ply-lam CLT의 라미나 및 합판의 수종, 접착제의 종류 및 Layer구성 등 최적생산을 위한 제조조건을 구명하고자 하였으며 그 결과는 다음과 같다. 블록전단시험을 통해 집성재, Ply-lam CLT, CLT 순으로 높은 강도를 나타냈다. 특히, 낙엽송 합판과 낙엽송 라미나의 복합구조로 제조되는 Ply-lam CLT의 전단강도는 집성재 전단강도 기준인 7.1 N/㎟을 통과하였다. 아울러 본 연구에서는 집성재, CLT, Ply-lam 접착에 사용된 접착제 종류에 따른 전단강도의 차이는 나타나지 않았다. 그러나 Ply-lam CLT의 경우에는 라미나와 합판의 수종에 따라 Ply-lam CLT의 전단강도의 차이를 나타냈다. 그 결과는 낙엽송 > 남양재 ≒ 육송 합판 순으로 높은 강도를 나타났다. Ply-lam CLT의 최적 구성은 낙엽송 합판과 낙엽송 라미나를 사용하는 경우이며 접착제는 용도에 따라 PRF, PUR을 선정하여 사용하면 될 것으로 판단된다. 목질재료 유형에 따른 전단강도 파괴 양상 결과 분석을 통하여 집성재는 shear parallel-to-grain, CLT는 rolling shear, Ply-lam CLT는 shear parallel-to-grain과 rolling shear가 복합적으로 나타났다. 이는 전단강도 결과와 밀접한 관련이 있으며 rolling shear로 인하여 CLT보다 Ply-lam CLT에서 더 높은 전단 강도를 나타내는 것으로 판단된다.

• 한국재료학회지
• /
• 제26권1호
• /
• pp.8-12
• /
• 2016

Effects of conventional rolling(CR) and differential speed rolling(DSR) on the microstructure and mechanical properties of Cu-Ni-Si alloy were investigated in detail. The copper alloy with thickness of 3 mm was rolled to 50 % reduction at ambient temperature without lubricant with a differential speed ratio of 2:1. The conventional rolling in which the rolling speed of upper and lower rolls is identical was performed under identical rolling conditions. The shear strain introduced by the CR showed positive values at positions of upper roll side and negative values at positions of lower roll side. However, it showed zero or positive values at all positions for the samples rolled by the DSR. The microstrucure and texture development of the as-rolled copper alloy did not show any significant difference between CR and DSR. The tensile strength of the DSR processed specimen was larger than that of the CR processed specimen. The effects of rolling methods on the microstructure and mechanical properties of the as-rolled copper alloy are discussed in terms of the shear strain.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 가을 학술발표회 논문집
• /
• pp.721-728
• /
• 2000

The shear behavior of sawtoothed artificial joints grouted with cement milk was investigated in the laboratory under constant normal stress conditions. Tests were conducted on joints with asperities having inclinations of 16.7$^{\circ}$ and 26.6$^{\circ}$, compresive strengths having 15MPa and 47MPa under a given range of normal stresses varying from 0.76 to 1.91 MPa and at a free condition of pitching, rolling and dilatancy. Results show that the effect of asperities on shear strength increase is significant up to asperity height to grout thickness (t/a) ratio of 0.3∼1.0. Increase of cohesion is the main cause of shear strength increase in cement grouted sawtoothed artificial joints.

• 한국재료학회지
• /
• 제28권2호
• /
• pp.113-117
• /
• 2018

Effects of annealing temperature on the microstructure and mechanical properties through thickness of a cold-rolled Cu-3.0Ni-0.7Si alloy were investigated in detail. The copper alloy with thickness of 3 mm was rolled to 50 % reduction at ambient temperature without lubricant and subsequently annealed for 0.5h at $200{\sim}900^{\circ}C$. The microstructure of the copper alloy after annealing was different in thickness direction depending on an amount of the shear and compressive strain introduced by rolling; the recrystallization occurred first in surface regions shear-deformed largely. The hardness distribution of the specimens annealed at $500{\sim}700^{\circ}C$ was not uniform in thickness direction due to partial recrystallization. This ununiformity of hardness corresponded well with an amount of shear strain in thickness direction. The average hardness and ultimate tensile strength showed the maximum values of 250Hv and 450MPa in specimen annealed at $400^{\circ}C$, respectively. It is considered that the complex mode of strain introduced by rolling effected directly on the microstructure and the mechanical properties of the annealed specimens.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.132-135
• /
• 2003

Asymmetric rolling, in which the ratio of the rotation rates of the upper and lower rolls was 2, has been used to introduce an intense plastic shear strain for the purpose of grain refinement and developing shear deformation textures through the sheet thickness to improve the strength and plastic strain ratio of AA1050 aluminum alloy sheets. The alloy sheets were rolled at room temperature without lubrication. The textures and microstructures of the sheets were investigated by x-ray diffraction and electron back-scattered diffraction (EBSD) analyses with emphasis on effects of combinations of rot ling directions.

• 한국재료학회지
• /
• 제28권5호
• /
• pp.295-300
• /
• 2018

Effects of annealing temperature on the microstructure and mechanical properties through thickness of a Cu-3.0Ni-0.7Si alloy processed by differential speed rolling are investigated in detail. The copper alloy with a thickness of 3 mm is rolled to a 50 % reduction at ambient temperature without lubricant and subsequently annealed for 0.5 h at $200-900^{\circ}C$. The microstructure of the copper alloy after annealing is different in the thickness direction depending on the amount of the shear and compressive strain introduced by the rolling; the recrystallization occurs first in the upper roll side and center regions which are largely shear-deformed. The complete recrystallization occurs at an annealing temperature of $800^{\circ}C$. The grain size after the complete recrystallization is finer than that of the conventional rolling. The hardness distribution of the specimens annealed at $500-700^{\circ}C$ is not uniform in the thickness direction due to partial recrystallization. This ununiformity of hardness corresponds well to the amount of shear strain in the thickness direction. The average hardness and ultimate tensile strength has the maximum values of 250 Hv and 450 Mpa, respectively, in the specimen annealed at $400^{\circ}C$. It is considered that the complex mode of strain introduced by rolling directly affects the microstructure and the mechanical properties of the annealed specimens.

• Journal of the Korean Wood Science and Technology
• /
• 제44권4호
• /
• pp.607-615
• /
• 2016

The delamination along the annual ring on the cross-section of laminae and the bonding strength according to the tangential angle between laminae were evaluated for the production of 3-ply cross-laminated timber (CLT) using domestic larch. Since there is no standard for CLT in Korea, the production and test of specimens for bonding strength followed the standard procedure of "Structural glued laminated timber" (KS F 3021). The standard specifies to exclude any measurement from the cracks of timbers resulted from drying or knots during delamination test of the glued laminated timbers. However, the failure of cross-sectional tissues along the annual rings was observed near the glue-line of all specimens during the delamination test. Because this phenomenon can generate defects in the CLT that may be exposed to various temperatures and relative humidities after the actual construction, the delamination percentage was measured by including this wood failure. As a result, the delamination percentage of the CLT which had been combined in such a way that the annual rings of outer lamina were directed inward was the lowest, which was around 13%, regardless of the annual ring direction of the middle lamina. On the other hand, the delamination percentage of the CLT which had been combined in such a way that the annual rings of outer lamina were directed outward was the highest, which was around 26%. Furthermore, end-split occurred in the outer lamina during the drying process of the boiling delamination test, which affected the delamination percentage. Therefore, the soaking delamination test was found to be more appropriate for evaluating the delamination strength of CLT. The block shear strength of larch CLT was $3.9{\pm}0.9$ MPa on average, which was 46% lower than the block shear strength requirement (7.1 MPa) of the standard, but satisfied the criteria of the block shear strength (3.5 MPa) of the European Standard (prEN 16351: 2013).