• 반도체디스플레이기술학회지
• /
• 제9권2호
• /
• pp.91-96
• /
• 2010

In recent years there have been considerable attentions on nanoimprint lithography (NIL) by the display device and semiconductor industry due to its potential abilities that enable cost-effective and high-throughput nanofabrication. Although one of the current major research trends of NIL is large-area patterning, the technical difficulties to keep the uniformity of the residual layer become severer as the imprinting area increases more and more. In this paper we consider the roll-to-plate type imprinting process. In the process a glass mold, which is placed upon the 2nd generation TFT-LCD glass sized substrate(370${\yen}$470 mm), is rolled by a rubber roller to achieve a uniform residual layer. The pressure distribution on the glass mold by rolling of the rubber roller is crucial information to analyze mold deformation, transferred pattern quality, uniformity of residual layer and so forth. In this paper the quantitative pressure distribution induced by rolling of the rubber roller was calculated with finite element analysis under the assumption of Neo-Hookean hyperelastic constitutive relation. Additionally the numerical results were verified by the experiments.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.310-313
• /
• 2009

오스테나이트계 고질소 스테인레스강 4 가지 후보강종인 HNS C1, C2, C3, C4에 대해 질소함량, 가압조건 따른 단조재와 온도 및 동일한 가압조건에서 Ni 합금원소 첨가유무에 따른 용체화 처리재(HNS C1, C3)의 물성평가와 실제 냉연 공정의 pass schedule 검증을 위한 모사실험을 통해 다음과 같이 요약 하였다. 1) 가압증가에 따른 질소함량의 증가로 강도 및 경도가 동시 상승하며, 결정립의 미세화 및 기계적 쌍정 발생이 많았다. 동일한 가압조건에서 Ni 첨가된 HNS C3가 Ni 미첨가한 HNS C1 보다 강도-연성 조합평가에서 열/냉간 가공성 등의 특성이 우수하였다. 2) 고질소강 스테인레스강의 적정한 용체화 처리온도 범위는 상용화된 AIS1304와 유사한 $1050^{\circ}C{\sim}1100^{\circ}C$이며, 용체화처리 후냉각방법의 변경(수냉과 공냉)에 따른 경도의 편차는 없었다. 냉연 pass schedule 검증을 위한 모사실험에서 초기 압연의 최적조건은 roll 속도 5mpm, pass당 압연율 $15{\sim}17%$였다.

• 대한금속재료학회지
• /
• 제50권4호
• /
• pp.316-323
• /
• 2012

The aim of this study is to investigate the effect of post heat treatment on bonding properties of roll cladded Ti/MS/Ti materials. First grade Ti sheets and SPCC mild steel sheets were prepared and then Ti/MS/Ti clad materials were fabricated by a cold rolling and post heat treatment process. Microstructure and point analysis of the Ti/MS interfaces were performed using the SEM and EDX Analyser. Diffusion bonding was observed at the interfaces of Ti/MS. The thickness of the diffusion layer increased with post heat treatment temperature and the diffusion layer was verified as having $({\epsilon}+{\zeta})+({\zeta}+{\beta}-Ti)$ intermetallic compounds at $700^{\circ}C$ and an $({\zeta}+{\beta}-Ti)$ intermetallic compound at $800^{\circ}C$, respectively. The micro Knoop hardness of mild steel decreased with post heat treatment temperature; however, those of Ti decreased at a range of $500{\sim}600^{\circ}C$ and showed a uniform value until $800^{\circ}C$ and then increased rapidly up to $900^{\circ}C$. The micro Knoop hardness value of the diffusion layer increased up to $700^{\circ}C$ and then saturated with post heat treatment. A T-type peel test was used to estimate the bonding forces of Ti/Mild steel interfaces. The bonding forces decreased up to $800^{\circ}C$ and then increased slightly with post heat treatment. The optimized temperature ranges for post heat treatment were $500{\sim}600^{\circ}C$ to obtain the proper formability for an additional plastic deformation process.

• 한국정밀공학회지
• /
• 제22권11호
• /
• pp.135-141
• /
• 2005

Measurement of five DOF motion errors in a ultra precision feed table was attempted in this study. Yaw and pitch error were measured by using a laser interferometer and roll error was measured by using the reversal method. Linear motion errors in the vertical and horizontal directions were measured by using the sequential two point method. In this case, influence of angular motion errors was compensated by using the previously measured ones by the laser interferometer and the reversal method. The capacitive type sensors and an optical straight edge were used in the reversal method and the sequential two point method. Influence of thermal deformation on sensor jig was investgated and minimized by the periodic measurement according to the variation of room temperature. Deviation of gain between sensors was also compensated using the step response data. 5 DOF motion errors of a hydrostatic table driven by the linear motor werer tested using the measurement method. In the horizontal direction, measuring accuracies for the linear and angular motion were within ${\pm}0.02\;{\mu}m$ and ${\pm}0.04$ arcsec, respectively. In the vertical direction, they were within ${\pm}0.02{\mu}m$ and ${\pm}0.05$ arcsec. From these results, it was found that the introduced measurement method was very effective to measure 5 DOF motion errors of the ultra precision feed tables.

• 한국재료학회지
• /
• 제4권2호
• /
• pp.241-249
• /
• 1994

항공기용 고력 AI합금인 7075 AI합금의 물성개선을 위한 가공열처리 방안으로서 과시효처리후 온간 및 냉간 압연에 의한 소성가공이 재결정조직과 강도에 미치는 영향에 대하여 연구하였다. 소송가공후 재결정처리에 의해 결정립을 미세화하는 공정에서 소성가공 전 과시효를 함으로써 재결정립의 미세화 정도는 더욱 현저하였다. 이는 과시효에 의한 조대한 석출물이 재결정처리시 핵생성 site로서 작용하였음을 의미한다. 본 연구에서 항복강도와 재결정립의 크기와는 Hall-petch식을 만족하지 않았으며 이는 등축이 아닌 연신된 결정조직에 기인된 결과로 보이며, 항복강도가 재결정립의 종횡비에 직선적으로 비례하였다. 또한 결정립 미세화를 통한 강도, 인성향상을 목적으로 하는 TMT(Thermo mechanical Treatment)공정에서는 심한 냉간가공에 의해서보다는 온간에서의 소성가공이 바람직함을 알 수 있었다.

• 대한금속재료학회지
• /
• 제50권5호
• /
• pp.345-351
• /
• 2012

A three-point bending test was performed on roll-bonded Mg/Al/STS clad-metal plates under two different testing conditions (Mg layer in tension, or STS in tension) and their mechanical response and fracture behavior were investigated. Bending strength was found to be greater under the condition of Mg layer in tension. Heat treatment at $200^{\circ}C$ increased the bending formability, suggesting the interfacial strength increased at $200^{\circ}C$. Under the condition of Mg in tension, the clad heat-treated at $300^{\circ}C$ and $400^{\circ}C$ fractured in two steps, with the first step associated with the interfacial fracture between Mg and Al, and the second the fracture of the Mg layer. STS/Al layers were found to be bent without complete fracture. Under the condition of STS in tension, the clad heat-treated at $300^{\circ}C$ and $400^{\circ}C$ exhibited a very small load drop at the displacement, which is similar to that of the first load drop associated with the interfacial fracture under the condition of Mg in tension. In this case, no interfacial cracks were found and the complete cut-through fracture of clad was observed at low temperature heat treatment conditions, suggesting excellent interfacial strength. When the heat treatment temperature was higher than $300^{\circ}C$, interfacial cracks were observed. The local stress condition and the position of the interface with respect to the surface were found to have a great influence on the fracture behaviors of clad metals.

• Steel and Composite Structures
• /
• 제32권5호
• /
• pp.571-582
• /
• 2019

This study aimed to assess the feasibility on the wide and long 9%Ni steel plate for use in the LNG storage inner tank shell. First, 5-m-wide and 15-m-long 9%Ni steel plates were test manufactured from a steel mill and specimens taken from the plates were tested for strength, toughness, and flatness to verify their performance based on international standards and design specifications. Second, plates with a thickness of 10 mm and 25 mm, a width of 4.8~5.0 m, and a length of 15 m were test fabricated by subjecting to pretreatment, beveling, and roll bending resulting in a final width of 4.5~4.8 m and a length of 14.8m with fabrication errors identical to conventional plates. Third, welded specimens obtained via shield metal arc welding used for vertical welding of inner tank shell and submerged arc welding used for horizontal welding were also tested for strength, toughness and ductility. Fourth, verification of shell plate material and fabrication was followed by test erection using two 25-mm-thick, 4.5-m-wide and 14.8-m-long 9%Ni steel plates. No undesirable welding failure or deformation was found. Finally, parametric design using wide and long 9%Ni steel plates was carried out, and a simplified design method to determine the plate thickness along the shell height was proposed. The cost analysis based on the parametric design resulted in about 2% increase of steel weight; however, the construction cost was reduced about 6% due to large reduction in welding work.