• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.03b
• /
• pp.419-426
• /
• 2000

The purpose of this study is to present the application of WFS co-mixtures for retaining wall as flowable backfill. The fly ash, generated at the Tae-An thermoelectric power plant, was used in this research and was classified as Class F. Green Sand, Furane Sand, and Coated Sand, which had been used at a foundry located in Pusan, were used. Couple of laboratory tests and small scale retaining wall tests were performed to obtain the physical properties of the WFS co-mixtures and the possibility of backfill materials of retaining wall. The range of permeability for all the co-mixtures was from 3.0${\times}$10$\^$-3/ cm/s to 6.0${\times}$10$\^$-5/ cm/s. The unconfined strength of the 28-day cured specimens reached around 550kPa. Results of the consolidated-undrained triaxial test showed that the internal friction angle is between 33.5$^{\circ}$ and 41.8$^{\circ}$. The lateral earth pressure against wall decreased up to 80% of initial pressure within a 12 hours and the total lateral earth pressure is less than that of typical granular soil. It was enough to construct the backfill for the standard retaining of 6m with just two steps, like fill the co-mixtures for half of retaining wall, and then fill the others after 1 day. The stability of retaining wall for overturning and sliding increased as the curing time elapsed.

• Geomechanics and Engineering
• /
• v.16 no.3
• /
• pp.321-329
• /
• 2018

Classic braced walls use struts and wales to minimize ground movements induced by deep excavation. However, the installation of struts and wales is a time-consuming process and confines the work space. To secure a work space around the retaining structure, an anchoring system works in conjunction with a braced wall. However, anchoring cannot perform well when the shear strength of soil is low. In such a case, innovative retaining systems are required in excavation. This study proposes an innovative earth-retaining wall that uses in situ soil confined in dual sheet piles as a structural component. A numerical study was conducted to evaluate the stability of the proposed structure in cohesionless dry soil and establish a design chart. The displacement and factor of safety of the structural member were monitored and evaluated. According to the results, an increase in the clearance distance increases the depth of safe excavation. For a conservative design to secure the stability of the earth-retaining structure in cohesionless dry soil, the clearance distance should exceed 2 m, and the embedded depth should exceed 40% of the wall height. The results suggest that the proposed method can be used for 14 m of excavation without any internal support structure. The design chart can be used for the preliminary design of an earth-retaining structure using in situ soil with dual steel sheet piles in cohesionless dry soil.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.8
• /
• pp.44-50
• /
• 2019

CMP is the most critical process in the manufacture of silicon wafers, and the use of retaining rings, which are consumable parts used in CMP equipment, is increasingly important. Since the retaining ring is made of plastic, it is not only weak in strength but also has the problem of taking a long time for the flattening operation of the ring itself performed before the CMP process, and of the imbalance of force due to bolt tightening causing uneven wear. In order to solve this problem, the retaining ring and the insert ring are integrally used, and the flatness of the retaining ring may be affected depending on the material of the insert ring. Also, the residual stress generated in the manufacturing process of the insert ring may cause distortion of the ring, which may adversely affect the precision polishing. In this study, when the insert ring is made of Zn or STS304, the thickness variation and the flatness of the retaining ring are compared and, finally, the material removal rate is analyzed by polishing the wafer by the oxide CMP process. Through these experiments, the effects of the insert ring material on the polishing accuracy of the wafers were investigated.

• Geomechanics and Engineering
• /
• v.25 no.3
• /
• pp.195-205
• /
• 2021

Time effect on the deformation and strength characteristics of geogrid reinforced sand retaining wall has become an important issue in geotechnical and transportation engineering. Three physical model tests on geogrid reinforced sand retaining walls performed under various loading conditions were simulated to study their rate-dependent behaviors, using the presented nonlinear finite element method (FEM) analysis procedure. This FEM was based on the dynamic relaxation method and return mapping scheme, in which the combined effects of the rate-dependent behaviors of both the backfill soil and the geosynthetic reinforcement have been included. The rate-dependent behaviors of sands and geogrids should be attributed to the viscous property of materials, which can be described by the unified three-component elasto-viscoplastic constitutive model. By comparing the FEM simulations and the test results, it can be found that the present FEM was able to be successfully extended to the boundary value problems of geosynthetic reinforced soil retaining walls. The deformation and strength characteristics of the geogrid reinforced sand retaining walls can be well reproduced. Loading rate effect, the trends of jump in footing pressure upon the step-changes in the loading rate, occurred not only on sands and geogrids but also on geogrid reinforced sands retaining walls. The lateral earth pressure distributions against the back of retaining wall, the local tensile force in the geogrid arranged in the retaining wall and the local stresses beneath the footing under various loading conditions can also be predicted well in the FEM simulations.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.2 no.1
• /
• pp.94-102
• /
• 1999

The retaining wall is a structure which was made for changing land form in many construction. The first role of the retaining wall is to maintain the slope stability. But recently, the amount of retaining wall have been increasing because of the expansion of construction works and the amenity of urban environment have been decreasing because of environmental destruction and the scenic heterogeneity. So we should consider the slope stability and ecological stability at the same time. The purpose of this study is to develop the retaining wall revegetation technology using the Eco-Stone, the structure of co-satisfying which included the slope stability and the revegetation effect. Eco-Stone is a structure which has high stability for earth pressure, settlement and drainage. And cost and term of construction works also have been decreased. Eco-Stone structure is one of factors composing the ecological network which is harmonize with surrounding environment. In this way, it is expected that the ecological habitats of various species would be restored.

• Structural Engineering and Mechanics
• /
• v.81 no.1
• /
• pp.93-102
• /
• 2022

The optimum design of reinforced concrete cantilever retaining walls subjected to seismic loads is an extremely important challenge in structural and geotechnical engineering, especially in seismic zones. This study proposes an adaptive sperm swarm optimization algorithm (ASSO) for economic design of retaining structure under static and seismic loading. The proposed ASSO algorithm utilizes a time-varying velocity damping factor to provide a fine balance between the explorative and exploitative behavior of the original method. In addition, the new method considers a reasonable velocity limitation to avoid the divergence of the sperm movement. The proposed algorithm is benchmarked with a set of test functions and the results are compared with the standard sperm swarm optimization (SSO) and some other robust metaheuristic from the literature. For seismic optimization of retaining structures, Mononobe-Okabe method is employed for dynamic loading conditions and total construction cost of the structure is considered as the single objective function. The optimization constraints include both geotechnical and structural restrictions and the design variables are the geometrical dimensions of the wall and the amount of steel reinforcement. Finally, optimization of two benchmark retaining structures under static and seismic loads using the ASSO algorithm is presented. According to the numerical results, the ASSO may provide better optimal solutions, and the designs obtained by ASSO have a lower cost by up to 20% compared with some other methods from the literature.

• Journal of the Korean GEO-environmental Society
• /
• v.23 no.1
• /
• pp.25-30
• /
• 2022

It is very important to investigate the ground properties of a construction site for the stability during the construction of the retaining wall. In the retaining wall construction stage, ground properties are checked through ground investigation, but the actual ground properties may be different from the ground investigation result. In order to analyze the stability of the retaining wall in real time, it is important to reflect the properties of the actual ground. Also, when it is judged that the wall is unstable, an appropriate solution must be provided for the stability of the wall. This study aims to present a technique for predicting the actual ground properties through a differential evolution algorithm and judging the stability of the earth wall in real time through the digital twin of the retaining wall.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.1
• /
• pp.83-90
• /
• 2004

Retaining walls with reinforced earth have been constructed around the world. The use of reinforced earth is a recent development in the design and construction of earth-retaining structure. It is believed that reinforced retaining wall has some advantages which make construction quite simple basically. It wilt take short construction time relatively, comparing, fur example with reinforced-concrete retaining wall. In addition, low price and easy construction will be good attractive points in practical point of view. In this study, five field-tests monitoring data for lateral pressures on geogrid-reinforced retaining wall have been compiled and evaluated. Based on field-tests it is found that horizontal displacements of the facing was measured to be about 0.19∼0.76% and that the maximum tensile strains of reinforcement was evaluated to be about 0.66∼1.98%. The maximum tensile strains, measured from each site, do not reach 5% of the practical allowable strain of the geogrid. And also it is found that the lateral pressure distributions of reinforced-earth retaining wall are close to a trapezoid shape like a flexible retaining wall system, instead of a theoretical triangular shape.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.152-155
• /
• 2003

The design process of concrete retaining walls includes multiple procedures such as structural analysis, member design, the production of calculation sheets, CAD, and itemized statements of Quantities and costs. The objective of this study is to develope an integrated design system that includes all the steps needed for concrete retaining wall design, and as a result, to improve the quality and efficiency of the design process. In this study, the design steps are divided into structural modules and database, and each module and database is systematically combined for the complete design process. The developed design system is based on Web environment. Therefore it can be used in real time and reduces the design work time and space.

• Progress in Superconductivity and Cryogenics
• /
• v.13 no.2
• /
• pp.13-16
• /
• 2011

This paper describes the reduction method of eddy current loss generated into a retaining ring installed in wound-field superconducting machine. In order to suggest the reduction method of eddy current loss of the retaining ring, this paper is divided into three parts. Firstly, eddy current loss of prototype model is calculated. Secondly, eddy current loss versus material and shape of the retaining ring is compared. Finally, the material and the shape of the retaining ring to reduce coupling loss generated by a time-varying magnetic field are proposed. In this paper, eddy current loss is calculated by 3-dimensional transient analysis.