• 대한기계학회논문집
• /
• 제15권1호
• /
• pp.49-60
• /
• 1991

본 연구에서는 "피로계수" (Fig.1)라는 새로운 개념을 도입하여 피로수명을 예측하였다. 먼저, 임의의 피로주기에서 피로계수 감소율은 피로주기의 지수함수를 따른다는 가정을 사용하고, 이를 적분하여 피로계수의 함수로 표현되는 피로수명식을 얻었다. 그리고 이 식에 변형률 파괴기준을 적용하여 최종적인 피로수명 예측식을 유도하였다. 이렇게 유도된 식은 재료상수가 결정되었을 때 임의의 응력상태하에서 의 피로수명을 예측할 수 있게 된다. 제안된 식을 탄소섬유 복합적층판에 적용하여 단일 응력에서의 피로 수명을 예측한 결과, 본 연구에서 제안한 피로수명 예측식(H '||'&'||' H curve)이 기존의 식보다 실험치와 더 잘 일치함을 알 수 있었다. 아울러 탄소섬유 강화 복합재료의 제반 피로특성을 살펴보았다.다.

• 대한기계학회논문집
• /
• 제19권6호
• /
• pp.1422-1430
• /
• 1995

Al6061 alloy reinforced with 15 volume% of Saffil fibers was fabricated by squeeze infiltration method. Uniform distribution of reinforcements and good bondings between reinforcements and matrix alloy were found in the microstructure of composites. Comparing with A16061 matrix alloy, tensile strength and elastic modulus of $Al_{2}$O$_{3}$/Al composites were increased up to 26% and 31%, respectively. Cyclic deformation and fatigue behavior of $Al_{2}$O$_{3}$/Al metal matrix composites were studied. The specimens were cycled using tension-tension(R=0.1) loading and under load controlled fatigue test. Cyclic stress-displacement curve through fatigue test was obtained. Fatigue strength of $Al_{2}$O$_{3}$/Al composites was about 200 MPa, i.e.0.55 of applied stress level(q). During fatigue test, $Al_{2}$O$_{3}$/Al composites displayed cyclic hardening at all applied stress levels. The most of resultant displacement due to permanent plastic deformation occurred in less than the first 5% of fatigue life. Displacement-to-failure of the fatigue test was smaller than that of the tensile test because of accumulative damage by cumulative plastic deformation.

• Journal of Microbiology and Biotechnology
• /
• 제1권1호
• /
• pp.37-44
• /
• 1991

A shuttle promoter-probe vector, pEB203, was derived from pBR322, pPL703 and pUB110. Using the vector, a useful DNA fragment, 319 bp EcoRI fragment, having strong promoter activity has been cloned from Bacillus subtills chromosomal DNA. Selection was based on chloramphenicol resistance which is dependent upon the introduction of DNA fragments allowing expression of a chloramphenicol acetyl transferase gene. The nucleotide sequence of the 319 bp fragment has been determined and the putative -35 and -10 region, ribosome binding site, and ATG initiation codon were observed. This promoter was named EB promoter and the resultant plasmid which can be used as an expression vector was named pEBP313. The crystal protein gene from B. thuringiensis subsp. kurstaki HD-73 was cloned downstream from the EB promoter without its own promoter. When the resultant plasmid, pBT313, was introduced into Escherichia coli and B. subtilis, efficient synthesis of crystal protein was observed in both cells, and the cp gene expression in B. subtilis begins early in the vegetative phase. The cell extracts from both clones were toxic to Hyphantria cunea larvae.

• Advances in aircraft and spacecraft science
• /
• 제7권4호
• /
• pp.353-369
• /
• 2020

This paper presents the flutter analysis and optimum design of axially functionally graded box beam cantilever wing section by considering various geometric and material parameters. The coupled dynamic equations of the continuous model of wing system in terms of material and cross-sectional properties are formulated based on extended Hamilton's principle. By expressing the lift and pitching moment in terms of plunge and pitch displacements, the resultant two continuous equations are simplified using Galerkin's reduced order model. The flutter velocity is predicted from the solution of resultant damped eigenvalue problem. Parametric studies are conducted to know the effects of geometric factors such as taper ratio, thickness, sweep angle as well as material volume fractions and functional grading index on the flutter velocity. A generalized surrogate model is constructed by training the radial basis function network with the parametric data. The optimized material and geometric parameters of the section are predicted by solving the constrained optimal problem using firefly metaheuristics algorithm that employs the developed surrogate model for the function evaluations. The trapezoidal hollow box beam section design with axial functional grading concept is illustrated with combination of aluminium alloy and aluminium with silicon carbide particulates. A good improvement in flutter velocity is noticed by the optimization.

• 복합신소재구조학회 논문집
• /
• 제3권2호
• /
• pp.1-10
• /
• 2012

In the present study, an Element-Based Lagrangian Formulation for the nonlinear analysis of shell structures is presented. The strains, stresses and constitutive equations based on the natural co-ordinate have been used throughout the Element-Based Lagrangian Formulation of the present shell element which offers an advantage of easy implementation compared with the traditional Lagrangian Formulation. The Element-Based Lagrangian Formulation of a 9-node resultant-stress shell element is presented for the anisotropic composite material. The element is free of both membrane and shear locking behavior by using the assumed natural strain method such that the element performs very well in thin shell problems. The arc-length control method is used to trace complex equilibrium paths in thin shell applications. Numerical examples for laminated composite curved shells presented herein clearly show the validity of the present approach and the accuracy of the developed shell element.

• 한국CDE학회논문집
• /
• 제11권2호
• /
• pp.148-155
• /
• 2006

This paper presents a new method for assessing the efficiency of production process plans using tolerance chart to lower production cost. The tolerance chart is used to predict the accuracy of a part that is to be produced following the process plan, and to carry out the quantitative measurement on the efficiency of the process plan. By comparing the values of design tolerances and their corresponding resultant tolerances calculated using the tolerance chart, the process plan that is incapable of satisfying the design requirements and the faulty production operations can be identified. Similarly, the process plan that imposes unnecessarily high accuracy and wasteful production operations can also be identified. For the latter, a quantitative measure on the efficiency of the process plan is introduced. The higher the unnecessary cost of the production, the poor is the efficiency of the process plan. A coefficient is introduced for measuring the process plan efficiency. The coefficient also incorporates two weighting factors to reflect the difficulty of manufacturing operations and number of dimensional tolerances involved. To facilitate the identification of the machining operations and the machined surfaces, which are related to the unnecessarily tight resultant tolerances caused by the process plan, a rooted tree representation of the tolerance chart is introduced, and its use is demonstrated. An example is presented to illustrate the new method. This research introduces a new quantitative process plan evaluation method that may lead to the optimization of process plans.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년도 제30회 춘계학술대회논문집
• /
• pp.221-226
• /
• 2008

Hydroxy-terminated polyether의 새로운 합성방법인 양이온 개환 공중합에 의해서 Ethylene oxide와 Tetrahydrofuran을 공중합 하였다. 중합은 1,4-Butandiol 존재 하에 $BF_3$ THF를 촉매로 반응이 진행되어 잘 제어된 Polyetherdiol을 합성할 수 있었다. Polyurethane 반응은 Polyetherdiol과 경화제로써 I-PDI/N-100 혼합물을 사용하였고, 경화촉매로 TPB/MA 혼합물을 사용하여 합성하였다. 이렇게 합성된 Polyurethane은 현재 미국에서 시판중인 ATK HTPE를 이용한 Polyurethane과 기계적 특성과 경화 거동을 비교 분석하였다.

• Structural Engineering and Mechanics
• /
• 제23권6호
• /
• pp.675-689
• /
• 2006

In structural analysis of tall buildings the traditional primary loading analysis approach that assumes all the loads are simultaneously applied to the fully built structure has been shown to be unsuitable by many researches. The construction sequential analysis that reflects the fact of the level-by-level construction of tall buildings can provide more reliable results and has been used more and more. However, too much computational cost has prevented the construction sequential analysis from its application in CAD/CAE software for building structures, since such an approach needs to deal with systematic changing of resultant stiffness matrices following level-by-level construction. This paper firstly analyzes the characteristics of assembling and triangular factorization of the stiffness matrix in the finite element model of the construction sequential analysis, then presents a fast construction sequential analysis strategy and a corresponding step-by-step active column solver by means of improving the existing skyline solver. The new strategy avoids considerably repeated calculation by only working on the latest appended and modified part of resultant stiffness matrices in each construction level. Without any simplification, the strategy guarantees accuracy while efficiency is greatly enhanced. The numerical tests show that the proposed strategy can be implemented with high efficiency in practical engineering design.

• 한국지진공학회논문집
• /
• 제2권3호
• /
• pp.83-86
• /
• 1998

The results from the Individual Plant Examination of External Event of Yonggwyang nuclear power plants, unit 3 & 4, in Korea have shown that the high degree of diversities of the experts' opinions on seismicity and attenuation models is su, pp.sed to be generic cause of uncertainty of APEs(annual exceedance probability) in the PAHA(probabilistic seismic hazard analysis). This study investigated the sensitivity of the focal depth, which is one of the most uncertain seismicity parameters in Korea, Significant differences in resultant values of annual exceedance probabilities and much more symmetrical shape of the resultant PDFs(probability density functions), in case of consideration of focal depth, are found. These two results suggest that, even for the same seismic input data set including the seismicity models and ground motion attenuation models, to consider focal depth additionally for probabilistic seismic hazard analysis evaluation makes significant influence on the distributions of uncertainties and probabilities of exceedance per year for the whole ranges of seismic hazard levels. These facts suggest that it is necessary to derive focal depth parameter more effectively from the historical and instrumental documents on earthquake phenomena in Koran Peninsula for the future study of PSHA.

• KSBB Journal
• /
• 제13권1호
• /
• pp.52-57
• /
• 1998

The present work proposes a simple electrochemical method applicable to any immobilization processes of oxidase using a Clark type oxygen electrode as a base transducer. The present work suggests an optimal immobilization technique among three different methods of glucose oxidase(GOD) onto one side of $37[\mu}$mthick blend membranes, composed o 80% of cellulose triacetate and 20% of polycaprolactone, on the basis of the maximum Michaelis-Menten parameter(Vm) determined by either steady state or transient analyses. The electrode system was made of disk type gold cathode(4mm diameter) and Ag/AgCl anode. One side of the blend membrane was in contact with the cathode surface while the other side was immobilized with GOD either in covalent-bond or cross-linked forms, the latter being covered by $25{\mu}$m thick dialysis membrane of cellulose acetate. The resultant current density was on-line monitored by a potentiostat while glucose level was varied from 1 to 20 mM. The present study shows that direct cross-linking of GOD with glutaraldehyde was mostly preferred for fabrication of glucose sensor, on the basis of resultant kinetic parameters from either steady state or transient analyses.