• Korean Journal of Agricultural and Forest Meteorology
• /
• v.16 no.3
• /
• pp.233-245
• /
• 2014

Nighttime correction of $CO_2$ flux is one of the most important and challenging tasks in eddy covariance measurements over a complex mountainous terrain. In this study, we have scrutinized the quality and the credibility of the $CO_2$ flux datasets which were produced by employing three different methods of nighttime correction, i.e., (1) friction velocity ($u^*$) correction, (2) light response curve (LRC) correction, and (3) advection-based van Gorsel (VG) correction. The whole year datasets used in our analysis were collected at the two KoFlux tower sites (i.e., GDK deciduous forest site at the upper hill and GCK coniferous forest site at the lower hill) located in the valley of Gwangneung National Arboretum in central Korea. The resultant magnitudes and patterns of ecosystem respiration ($R_E$), gross primary productivity (GPP), and net ecosystem exchange (NEE) of $CO_2$ showed marked differences among the datasets produced with three different correction methods, which were also site-specific. The examination from micrometeorological and ecological perspectives suggests that the major cause of some inconsistency seems to be associated with the advection of $CO_2$ along the sloping terrain and the inappropriate selection of the correction data that might have been already affected by advective flows. The comparison with the results from other studies indicated that the overall characteristics of the corrected $CO_2$ fluxes at GDK and GCK (except those with LRC correction) were well within the ranges reported in the literature for various ecosystems in East Asia in similar latitudes. However, our study also implies that there will be always a room for further improvement in the present datasets. Therefore, caution must be exercised for the data users in order to properly use the updated version of datasets through transparent, open and participatory communication with data producers.

• Journal of the Korean Geographical Society
• /
• v.31 no.1
• /
• pp.19-37
• /
• 1996

This paper aims at examining the regional difference of changes in the business organization of retailing in the Seoul metropolitan areas, as an attempt to understand regional structure of retailing within metropolitan areas showing the trend of suburbanization. On the national level, retail sales have concentrated on the large metropolitan areas, especially on the Seoul metropolitan area, with the concentration of population and income. Within metropolitan areas, the suburbanization of retailing has made the larger structure of retail and multi-store retail appeared. In order to confirm such phenomenon, this paper is to analyze and to compare the industrial composition of retailing using industry data of 1979 and 1991. And this paper is to analyze the regional changes in the characteristics of business organization of retailing, with the index including the percentages of establishments with less than under four employees, juridical establishments, employees of ordinary times, and the annual sales per establishment of detailing. The characteristics of business organization of retailing in analyzed by principal components analysis, and the types with component in each district (city, county, ward) is analyzed by cluster analysis(Ward method). The data of 1979 were obtained from the statistics in the Census of Wholesale and Retail Trade published by the National Bureau of Statistics of Economic Planning Board, and that of 1991 were obtained from the statistics in the Report on Establishment Census (Vol.3 Wholesale and Retail Trade) published by the National Statistics Office. The following are resultant findings. 1. In Seoul metropolitan area, changes in the industrial composition of retailing with annual sales from, 1979 to 1991 show very higher composition rates of 'general merchandise stores' and 'retailing of personal transport equipment and gasoline service stations', but comparatively lower composition rates of 'retailing of food, beverages and tobacco', 'retailing of textiles, clothing, footwear and apparel accessaries', 'general retail trade, n.e.c.',and 'retailing of household fuel'. 2. The characteristics of business organization of retailing in Seoul metropolitan area presents the prevailence of small, personal business organization and especially larger employees of ordinary times. 3. Business components of retailing by principal components analysis in Seoul metropolitan area are follows: 1 All retaining industries are larger business scale. 2. Larger business take the 'retailing of taxtiles, clothing, footwear and apparel accessories', 'retailing of furniture, home furnishing and equipment', and 'retailing of jewellery and watches' is main characteristic legal organization and employees of ordinary times. 4. Types changes in business organization of retailing in Seoul metropolitan area represent legal organization and employees of ordinary times taking the 'retailing of textiles, clothing, footwear and apparel accessories', 'retailing of furniture, home furnishing and equipment',and 'retailing of jewellery and equipment', and 'retailing of jewellery and watches', and legal organization taking 'general retail trade, n.e.c.' in 1979. All retailing industries are changed into larger business scale, in 1991. These phenomena of business changes appeared southeastern regions in Kyunggi-do(province). And larger business scale taking the 'retailing of textiles, clothing, footwear and apparel accessories', 'retailing of jewellery and watches', and 'general retail trade, n.e.c.; are appeared in the legal organization in 1979. 'Retailing of personal transport equipment and gasoline service stations' are appeared in employees of ordinary times in 1991. These phenomena of business changes in appeared in eastern and northern regions in Kyunggi-do. 5. Changes in the business organization of retailing in Seoul metropolitan area is appeared in legal organization and employees of ordinary times for some industries in 1979, larger business scale of retailing and employees of ordinary times in 'retailing of personal transport equipment and gasoline service stations' are the characteristics in 1991.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.11 no.2
• /
• pp.144-149
• /
• 2018

The eggs are incubated for 18 days through the generator and incubated in the developing incubator. During the developmental period, the weight loss of the fetus is correlated with the ventricular formation, and the proper ventricular formation is also associated with the healthy embryonic hatching and the egg hatching rate. However, in the incubator period of the domestic hatchery, it is a reality to acquire the resultant side by the Iranian standard weight measurement with the experience of the hatchery and the person concerned and the development period without the apparatus for measuring the present weight. As a result, prevalence of early mortality, hunger and illness during hatching are frequent. Monitoring the reduction of weaning weight is crucial to obtaining chick quality and hatching performance with weight changes within the development machine. Water loss is different depending on the size of eggs, egg shell, and elder group. We can expect to increase the hatching rate by measuring the weight change in real time and optimizing the ventilation change accordingly. There is a need to develop a real-time measurement system that can control 10 to 13% reduction of the total weight during hatching. The system through this study is a way to check the one - time directly when moving the existing egg, and it is impossible to control the measurement of the fetal water evaporation within the development period. Unlike systems that do not affect the hatching rate, four load cells are connected in parallel on the Arduino sketch board and the AT-command command is used to connect the mobile phone and computer in real time. The communication speed of Bluetooth was set to 15200 to match the communication speed of Arduino and Hyper-terminal program. The real - time monitoring system was designed to visually check the change of the weight of the fetus in the artificial incubator. In this way, we aimed to improve the hatching rate and health condition of the hatching eggs.

• Journal of Intelligence and Information Systems
• /
• v.16 no.2
• /
• pp.129-141
• /
• 2010

An Internet shopping mall for clothing operates a warehouse for packing and shipping products to fulfill its orders. All the products in the warehouse are put into the boxes of same brands and the boxes are stored in a row on shelves equiped in the warehouse. To make picking and managing easy, boxes of the same brands are located side by side on the shelves. When new products arrive to the warehouse for storage, the products of a brand are put into boxes and those boxes are located adjacent to the boxes of the same brand. If there is not enough space for the new coming boxes, however, some boxes of other brands should be moved away and then the new coming boxes are located adjacent in the resultant vacant spaces. We want to minimize the movement of the existing boxes of other brands to another places on the shelves during the warehousing of new coming boxes, while all the boxes of the same brand are kept side by side on the shelves. Firstly, we define the adjacency of boxes by looking the shelves as an one dimensional series of spaces to store boxes, i.e. cells, tagging the series of cells by a series of numbers starting from one, and considering any two boxes stored in the cells to be adjacent to each other if their cell numbers are continuous from one number to the other number. After that, we tried to formulate the problem into an integer programming model to obtain an optimal solution. An integer programming formulation and Branch-and-Bound technique for this problem may not be tractable because it would take too long time to solve the problem considering the number of the cells or boxes in the warehouse and the computing power of the Internet shopping mall. As an alternative approach, we designed a fast heuristic method for this reallocation problem by focusing on just the unused spaces-empty cells-on the shelves, which results in an assignment problem model. In this approach, the new coming boxes are assigned to each empty cells and then those boxes are reorganized so that the boxes of a brand are adjacent to each other. The objective of this new approach is to minimize the movement of the boxes during the reorganization process while keeping the boxes of a brand adjacent to each other. The approach, however, does not ensure the optimality of the solution in terms of the original problem, that is, the problem to minimize the movement of existing boxes while keeping boxes of the same brands adjacent to each other. Even though this heuristic method may produce a suboptimal solution, we could obtain a satisfactory solution within a satisfactory time, which are acceptable by real world experts. In order to justify the quality of the solution by the heuristic approach, we generate 100 problems randomly, in which the number of cells spans from 2,000 to 4,000, solve the problems by both of our heuristic approach and the original integer programming approach using a commercial optimization software package, and then compare the heuristic solutions with their corresponding optimal solutions in terms of solution time and the number of movement of boxes. We also implement our heuristic approach into a storage location assignment system for the Internet shopping mall.

• Restorative Dentistry and Endodontics
• /
• v.34 no.5
• /
• pp.450-459
• /
• 2009

The aim of this study was to measure the initial dynamic modulus changes of light cured composites using a custom made rheometer. The custom made rheometer consisted of 3 parts: (1) a measurement unit of parallel plates made of glass rods, (2) an oscillating shear strain generator with a DC motor and a crank mechanism, (3) a stress measurement device using an electromagnetic torque sensor. This instrument could measure a maximum torque of 2Ncm, and the switch of the light-curing unit was synchronized with the rheometer. Six commercial composite resins [Z-100 (Z1), Z-250 (Z2), Z-350 (Z3), DenFil (DF), Tetric Ceram (TC), and Clearfil AP-X (CF)] were investigated. A dynamic oscillating shear test was undertaken with the rheometer. A certain volume ($14.2\;mm^3$) of composite was loaded between the parallel plates, which were made of glass rods (3 mm in diameter). An oscillating shear strain with a frequency of 6 Hz and amplitude of 0.00579 rad was applied to the specimen and the resultant stress was measured. Data acquisition started simultaneously with light curing, and the changes in visco-elasticity of composites were recorded for 10 seconds. The measurements were repeated 5 times for each composite at $25{\pm}0.5^{\circ}C$. Complex shear modulus G*, storage shear modulus G', loss shear modulus G" were calculated from the measured strain-stress curves. Time to reach the complex modulus G* of 10 MPa was determined. The G* and time to reach the G* of 10 MPa of composites were analyzed with One-way ANOVA and Tukey's test ($\alpha$ = 0.05). The results were as follows. 1. The custom made rheometer in this study reliably measured the initial visco-elastic modulus changes of composites during 10 seconds of light curing. 2. In all composites, the development of complex shear modulus G* had a latent period for $1{\sim}2$ seconds immediately after the start of light curing, and then increased rapidly during 10 seconds. 3. In all composites, the storage shear modulus G" increased steeper than the loss shear modulus G" during 10 seconds of light curing. 4. The complex shear modulus of Z1 was the highest, followed by CF, Z2, Z3, TC and DF the lowest. 5. Z1 was the fastest and DF was the slowest in the time to reach the complex shear modulus of 10 MPa.

• Pediatric Gastroenterology, Hepatology & Nutrition
• /
• v.5 no.2
• /
• pp.158-165
• /
• 2002

Purpose: We designed this retrospective study to establish the incidence of diagnosic delay in children diagnosed with acute appendicitis and to identify associated factors with delayed diagnosis and its impact on the clinical course. Methods: All cases of children under 15 years of age who underwent appendectomy from 1996 to 2001 at Gangneung Asan Hospital were reviewed. We reviewed signs and symptoms, type of health professional first contacted, the advice given by the health professional and a history of appendicitis in first degree relatives. Diagnostic period is the time elapsed between first complaints and definitive diagnosis. Delay was defined as diagnostic period exceeded the 48 hours. Postoperative course and complications were also reviewed. Results: Incidence of diagnostic delay differed by whether diarrhea and fecalith on X-ray were present. Also children whose parents were advised to observe them at home were more likely to have a diagnostic delay. In almost half of the cases in delayed group, initial diagnosis was not acute appendicitis but gastroenteritis. The perforation rate in non-delayed group was 22%, whereas 87% in delayed group. The delayed group showed a higher number of postoperative complication and a longer hospitalization period. Conclusions: Diarrhea with abdominal pain and fever in children should not be dismissed as gastroenteritis, respiratory infections or other common disorders. Our study suggests that physicians have a responsibility to prevent diagnostic delay and resultant perforation of acute appendicitis in children by having a high index of suspicion about acute appendicitis.

• The Korean Journal of Nuclear Medicine
• /
• v.39 no.3
• /
• pp.174-181
• /
• 2005

Purpose: Reduction of respiratory motion artifacts in PET images was studied using respiratory-gated PET (RGPET) with moving phantom. Especially a method of generating simulated helical CT images from 4D-CT datasets was developed and applied to a respiratory specific RGPET images for more accurate attenuation correction. Materials and Methods: Using a motion phantom with periodicity of 6 seconds and linear motion amplitude of 26 mm, PET/CT (Discovery ST: GEMS) scans with and without respiratory gating were obtained for one syringe and two vials with each volume of 3, 10, and 30 ml respectively. RPM (Real-Time Position Management, Varian) was used for tracking motion during PET/CT scanning. Ten datasets of RGPET and 4D-CT corresponding to every 10% phase intervals were acquired. from the positions, sizes, and uptake values of each subject on the resultant phase specific PET and CT datasets, the correlations between motion artifacts in PET and CT images and the size of motion relative to the size of subject were analyzed. Results: The center positions of three vials in RGPET and 4D-CT agree well with the actual position within the estimated error. However, volumes of subjects in non-gated PET images increase proportional to relative motion size and were overestimated as much as 250% when the motion amplitude was increased two times larger than the size of the subject. On the contrary, the corresponding maximal uptake value was reduced to about 50%. Conclusion: RGPET is demonstrated to remove respiratory motion artifacts in PET imaging, and moreover, more precise image fusion and more accurate attenuation correction is possible by combining with 4D-CT.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.24 no.1
• /
• pp.33-38
• /
• 2020

Purpose Vitamin D is essential for maintaining bone health, controling cell proliferation or differentiation, strengthening immune function by controlling calcium metabolism in the body. Vitamin D deficiency can lead to increase the risk of rickets, osteoporosis, cardiovascular disease, diabetes and cancer. Especially, South Korea is one of the highest population proportion of vitamin D deficiency. Accurate determination of levels of 25-OH-VitD or 25-OH-VitD3 in blood serum is required for the diagnosis and treatment of vitamin D deficiency. In this study, radioimmunoassay of 25-OH-VitD and 25-OH-VitD3 was performed and compared to evaluate the effectiveness of Vitamin D radioimmunoassay. Materials and Methods Serum 25-OH-VitD and 25-OH-VitD3 levels were measured using radioimmunoassay. The interrelationship, reproducibility and population distribution rate were evaluated. In addition, the internal quality control was performed at Asan Medical Center from April 2017 to June 2019 and the result of external quality control (Interagency proficiency evaluation) of first and second half of 2018 hosted by the Korean Society of Nuclear Medicine Technology (KSNMT). Both tests were measured by same manufacturer's reagent. Results 25-OH-VitD showed a strong positive correlation on 97 samples, as 25-OH-VitD3 x 0.9 + 0.3 (R>0.9). In repeated measurement, the average Diff(%) value of the reproducibility evaluation of 25-OH-VitD and 25-OH-VitD3 were 7.7% and 7.4%, respectively. Population distribution results showed no statistically significant differences(p>0.05). The resultant value of internal quality control, which measured from April, 2017 to June 2019 in Blood test room of Nuclear Medicine at Asan Medical Center, showed average (CV%) 6.2% and 6.8%, respectively. As a result of the external quality control (interagency proficiency evaluation) Z value obtained under 2.0, as shown below; Conclusion The interrelationship, reproducibility, population distribution rate, internal quality control and external quality control between 25-OH-VitD and 25-OH-VitD3 radioimmunoassay shows superior outcome. Radioimmunoassay, which can be alone measured in the blood as 25-OH-VitD or 25-OH-VitD3, is considered suitable screening tests for the diagnosis of vitamin D deficiency.

• Journal of Korean Neurosurgical Society
• /
• v.29 no.3
• /
• pp.379-388
• /
• 2000

Objective : Although transoral transpharyngeal approach is a very useful method for the lesions of craniovertebral junction, it is not frequently used because of anatomical unfamilarity, risk of cerebrospinal fluid(CSF) leakage, and resultant postoperative meningitis. To evaluate the usefulness of transoral transpharyngeal approach for various lesions of craniovertebral junction, clinical characteristics and the results of this approach are investigated. Methods : Transoral transpharyngeal approaches were performed in eight cases between 1996 and 1999. Among them, there were three basilar invaginations due to congenital anomalies, two odontoid type I fractures, two atlantoaxial dislocations, and one pseudotumor. Surgical methods included five cases of anterior decompression and posterior fusion, two anterior approaches for decompression and one transoral approach for biopsy. Results : This procedure allowed immediate clinical improvement in all cases. In seven patients with preoperative motor deficit showed a progressive neurological improvement. The follow-up plain x-rays demonstrated successful bony fusion in all patients. Only one patient suffered from postoperative wound dehiscence, but she completely recovered after wound revision. There was no complication of postoperative CSF leakages. Conclusions : Transoral transpharyngeal approach for the ventral lesions of craniovertebral junction, can be used as a relatively simple and effective method.

• Restorative Dentistry and Endodontics
• /
• v.23 no.1
• /
• pp.54-67
• /
• 1998

The purposes of this study were to evaluate the efficiency of dentin cutting and root-end cavity preparation, and to determine the incidence of tooth crack when root-end retrograde cavity preparation was done with. ultrasonic diamond instruments. To evaluate the efficiency of dentin cutting, ultrasonic diamond and stainless steel instruments were applied to 20 exposed bovine dentin surfaces perpendicularly or parallely at the low, and medium power settings for 1 minute ($Miniendo^{TM}$, EIE, CA, U.S.A.). The resultant cavity depth was measured. To evaluate the efficiency of cavity preparation and to investigate the incidence of tooth crack, 165 mesiobuccal, distobuccal and palatal root-ends of extracted human maxillary first molars were resected by 3 mm perpendicularly to the long axis of tooth using a slow speed diamond saw after root canal preparation and filling. Retrocavities were prepared using a ultrasonic diamond instrument or a stainless steel one of the low- or medium power settings of 2 or 6. Time consumed and the number of strokes used for the cavity preparation were measured and the incidence of tooth cracks was evaluated under a stereomicroscope. The results were as follows: Both at the low and medium power settings, and both with perpendicularly- and parallely applied tips to dentin, diamond instruments showed higher dentin cutting efficiency than stainless steel ones did (p<0.01). When tips were applied to dentin perpendicularly, both diamond instrument and stainless steel one showed higher cutting efficiency with medium power setting than with low power one (p<0.01). Both at the low- and medium power settings, both diamond instrument and stainless steel one showed higher cutting efficiency when tips were applied perpendicularly to dentin surface than applied parallely (p<0.01). At the medium power setting, the number of stroke and time consumed were less with diamond instrument than with stainless steel one (p<0.05) for the retrograde cavity preparation. At the low power setting, diamond instrument induced less tooth cracks than stainless steel one did (p<0.01).