• 대한기계학회논문집A
• /
• 제29권3호
• /
• pp.425-431
• /
• 2005

The efficiency of complex slurry preparation route for developing the high performance SiC matrix of $RS-SiC_{f}/SiC$ composites has been investigated. The green bodies for RS-SiC materials prior to the infiltration of molten silicon were prepared with various C/SiC complex slurries, which associated with both the sizes of starting SiC particles and the blending conditions of starting SiC and C particles. The characterization of Rs-SiC materials was examined by means of SEM, EDS and three point bending test. Based on the mechanical property-microstructure correlation, the process optimization is also discussed. The flexural strength of Rs-SiC materials greatly depended on the content of residual Si. The decrease of starting SiC particle size in the C/SiC complex slurry was effective for improving the flexural strength of RS-SiC materials.

• 한국세라믹학회지
• /
• 제44권7호
• /
• pp.381-386
• /
• 2007

A porous reaction bonded silicon carbide (RBSC) was fabricated by a molten Si infiltration method. The porosity and flexural strength of porous RBSC fabricated in this study were dependent upon the amount of carbon source used in the SiC/carbon preform as well as the amount of Si infiltrated into the SiC/carbon preform. The porosity and flexural strength of porous RBSC were in the range of $20 vo1.{\sim}49 vo1.%$ and $38{\sim}61 MPa$, respectively. With increase of carbon contents and molten Si for infiltration, volume fraction of the pores was gradually decreased, and flexural strength was increased. The porous RBSCs fabricated with the same amount of molten Si show less residual Si around neck with increase of carbon source, as well as a new SiC was formed around neck which resulted in the decreased porosity and improvement of the flexural strength. In addition, decrease of the porosity and increase of the flexural strength were also obtained by increase of the amount of molten Si with the same amount of carbon source. However, it was found that the flexural strength of porous RBSC depends on the porosity rather than the amount of the newly formed SiC in neck phase between SiC particles used as a starting material.

• Structural Engineering and Mechanics
• /
• 제65권2호
• /
• pp.163-171
• /
• 2018

Plain concrete is a brittle material with a very low tensile strength compared to compressive strength and critical tensile strain. This study analyzed the dynamic characteristics of high-performance fiber-reinforced cementitious composites based on slurry-infiltrated fiber concrete (SIFCON-based HPFRCC), which maximizes the steel-fiber volume fraction and uses high-strength mortar to increase resistance to loads, such as explosion and impact, with a very short acting time. For major experimental variables, three levels of fiber aspect ratio and five levels of fiber volume fraction between 6.0% and 8.0% were considered, and the flexural strength and toughness characteristics were analyzed according to these variables. Furthermore, three levels of the aspect ratio of used steel fibers were considered. The highest flexural strength of 65.0 MPa was shown at the fiber aspect ratio of 80 and the fiber volume fraction of 7.0%, and the flexural strength and toughness increased proportionally to the fiber volume fraction. The test results according to fiber aspect ratio and fiber volume fraction revealed that after the initial crack, the load of the SIFCON-based HPFRCC continuously increased because of the high fiber volume fraction. In addition, sufficient residual strength was achieved after the maximum strength; this achievement will bring about positive effects on the brittle fracture of structures when an unexpected load, such as explosion or impact, is applied.

• 한국구조물진단유지관리공학회 논문집
• /
• 제17권5호
• /
• pp.49-58
• /
• 2013

축소모형 원형기둥 실험체 8개를 제작하여 일정한 축력 하에서 반복 횡하중을 가력하는 실험을 수행하였다. 실험체들은 형상비 4.5인 실험체로 설계되었다. 실험체의 주요변수는 횡방향철근비, 축방향철근비, 축방향철근 항복강도와 축력비이다. 기둥 실험체들의 실험결과들은 축방향철근비, 횡철근비와 축력비에 따라 등가점성비, 잔류변형, 유효강성등과 같은 내진성능이 다르게 나타났다. 낮은 항복강도의 축방향철근이 적용된 실험체는 등가점성감쇠비와 잔류변형과 같은 내진성능이 낮게 나타났다. 국내의 도로교설계기준에 휨 초과강도 규정이 2012년에 채택되었다. 실험결과들은 공칭강도, 비선형 모멘트-곡률 해석 결과, AASHTO LRFD 및 도로교설계기준 (한계상태설계법)과 같은 기준들과 비교하였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.941-944
• /
• 2008

본 연구는 화재피해를 입은 고강도 철근 콘크리트 구조부재의 폭렬발생시 구조성능을 파악하기 위한 연구로 압축강도 55MPa의 휨 부재와 압축부재를 화재피해를 입은 시간을 주요변수로 30분, 60분 및 90분간 화재 실험을 실시하였다. 휨 부재의 경우 피복두께에 따라 폭렬의 정도와 구조성능의 감소에서 차이를 보였으며, 피복 두께가 두꺼운 경우에 폭렬 면적 및 잔존강도의 감소폭이 크게 나타났다. 압축부재의 경우 폭렬로 인해 손실된 면적의 양은 화재피해를 입은 시간에 영향을 크게 받지 않았으나, 잔존강도의 경우 콘크리트가 고온에 오래 노출될수록 큰 감소폭을 보였고, 부재강성의 감소폭은 더욱 크게 나타났다. 따라서 고강도 콘크리트구조물에 화재가 발생하였을 경우 폭렬의 양상과 화재피해를 입은 시간에 따라 구조물의 잔존강도를 예측 할 수 있으며, 이를 이용하여 구조물의 재사용 여부의 판단 및 보수 보강에 필요한 자료를 제시할 수 있다.

• Advances in concrete construction
• /
• 제8권4호
• /
• pp.311-320
• /
• 2019

In this study, the effect of cellulose nanocrystals (CNCs) on the fire resistance properties of fiber-reinforced cement composites was investigated. The main variables were CNCs content (0.4, 0.8 and 1.2vol.% compared with cement), steel fiber ratio, and exposure temperature (100, 200, 400, 600 and 800℃). The fire resistance properties, i.e., residual compressive strength, flexural strength, and porosity, were evaluated in relation with the exposure temperature of the specimens. The CNCs suspensions were prepared to composited dispersion method of magnetic stirring and ultra-sonication. CNCs are effective for increasing the compressive strength at high temperatures but CNCs do not seem to have a significant effect on flexural reinforcement. Porosity test result showed CNCs reduce the non-hydration area inside the cement and promote hydration.

• 한국터널지하공간학회 논문집
• /
• 제15권3호
• /
• pp.175-186
• /
• 2013

본 연구에서는 Model Code 2010에 제시된 실험방법에 근거하여 설계강도 60MPa의 강섬유보강 콘크리트의 휨강도와 잔존강도, 휨인성을 평가하였다. 비교를 위하여 설계강도 40MP의 강섬유보강 콘크리트도 실험하였다. 또한, 배합의 평가를 위하여 파괴된 시험체의 파괴면을 육안으로 관찰하여 강섬유의 분산도를 평가하였다. 본 실험에서 사용된 강섬유는 형상비 64, 67 및 80의 국내산 후크 강섬유이다. 강섬유 혼입률은 체적에 대하여 0.5%로 동일하다. 실험결과, 설계강도 60MPa에서는 형상비가 큰 강섬유가 혼입된 강섬유보강 콘크리트만이 Model Code 2010에서 제시된 요구성능을 만족하는 것으로 나타났다. 고강도 콘크리트에서는 큰 형상비의 강섬유가 심대한 균열에서 충분한 인성을 확보하는데 기여할 수 있는 것으로 판단된다. 또한, 섬유의 고른 분산도 확보를 위해서는 낮은 슬럼프가 유리한 것으로 나타났다.

• 한국강구조학회 논문집
• /
• 제23권6호
• /
• pp.647-657
• /
• 2011

본 논문에는 국부좌굴이 발생하는 휨부재의 유한요소해석 및 실험에 근거한 단면의 휨강도에 대하여 기술하였다. 박판으로 구성된 휨부재는 단면조건 및 횡방향 경계조건에 따라서 국부좌굴, 횡-비틀림좌굴 및 두 좌굴의 혼합좌굴이 발생하게 된다. 플랜지나 복부의 폭-두 께비가 큰 경우 횡-비틀림좌굴 발생 이전에 국부좌굴이 발생하며, 국부좌굴은 휨부재의 횡-비틀림좌굴강도에 영향을 미치게 된다. 이런 현상은 박판 형강의 휨강도 산정 시 고려하여야 한다. 다양한 폭-두께비를 갖는 플랜지와 복부판으로 구성된 휨부재의 해석에 국부좌굴 및 횡좌굴 모드의 초기처짐 및 잔류응력을 포함하였다. 해석결과 및 실험에 근거하여 국부좌굴과 횡-비틀림좌굴을 고려하는 설계강도식을 제안하였다. 제안된 직접강도법은 실험에 근거한 강도식과 유효단면 대신 총단면의 단면계수를 사용한다. 제안된 강도식에 의한 휨강도를 AISC, EC3 및 도로교설계기준과 비교하여 보았다. 제안된 직접강도법은 국부좌굴과 횡-비틀림좌굴의 혼합 유무와 상관없이 휨부재의 휨강도를 적절하게 예측할 수 있는 것으로 판단되었다.

• Structural Engineering and Mechanics
• /
• 제82권1호
• /
• pp.93-105
• /
• 2022

The brittleness of concrete can be overcome by fiber reinforcement that controls the crack mechanisms of concrete. Corrosion-related durability issues can be prevented by synthetic fibers (SFs), while macro synthetic fibers have proven to be particularly effective to provide ductility and toughness after cracks. This experimental study has been performed to investigate the comparative flexural and mechanical behavior of four different macro-synthetic fiber-reinforced concretes (SFRCs). Two polyamide fibers (SF1 and SF2) with different aspect ratios and two different polypropylene fiber types (SF3 and SF4) were used in production of SFRCs. Four different SFRCs and reference concrete were compared for their influences on the toughness, compressive strength, elastic modulus, flexural strength, residual strength and splitting tensile strength. The outcomes of the study reveal that the flowability of reference mixture decreases after addition of SFs and the air voids of all SFRC mixtures increased with the addition of macro-synthetic fibers except SFRC2 mixture whose air content is the same as the reference mixture. The results also revealed that with the inclusion of SFs, 11.34% reduction in the cube compressive strength was noted for SFRC4 based on that of reference specimens and both reference concrete and SFRC exhibited nearly similar cylindrical compressive strength. Results illustrated that SFRC1 and SFRC4 mixtures consistently provide the highest and lowest flexural toughness values of 36.4 joule and 27.7 joule respectively. The toughness values of SFRC3 and SFRC4 are very near to each other.

• 한국지진공학회논문집
• /
• 제19권2호
• /
• pp.75-83
• /
• 2015

The purpose of this study is to improve the previous damage evaluation model for RC members which is proposed by Igarashi[1] in 2010.The previous model was not confirmed by enough data of damage such as, residual crack length, width and area for exfoliation of concrete, etc. In addition, validation of the model is still insufficient. Therefore, experiment of a real-scale RC structure and experiment of RC columns using the high-strength concrete were conducted to gather the data of damage in RC members. The investigation has been conducted gathering the data not only additional experiments data but also existing data for modification of damage evaluation model. It has been investigated on changing damage in RC due to axial force ratio, shear reinforcement and shear span ratio. As a result, several problems were founded in the previous model, such as, hinge length($l_p$), spacing of flexural crack($S_{av,f}$), total width of flexural cracks regulated by maximum width of flexural crack($n_f$) and total width of shear cracks regulated by maximum width of shear crack($n_s$). New model is proposed and evaluated the damage properly.