DOI QR코드

DOI QR Code

Effect of steel fiber volume fraction and aspect ratio type on the mechanical properties of SIFCON-based HPFRCC

  • Kim, Seugnwon (Department of Civil Engineering, Kangwon National University) ;
  • Jung, Haekook (Department of Civil Engineering, Kangwon National University) ;
  • Kim, Yongjae (Department of Civil Engineering, Kangwon National University) ;
  • Park, Cheolwoo (Department of Civil Engineering, Kangwon National University)
  • Received : 2017.12.15
  • Accepted : 2017.12.18
  • Published : 2018.01.25

Abstract

Plain concrete is a brittle material with a very low tensile strength compared to compressive strength and critical tensile strain. This study analyzed the dynamic characteristics of high-performance fiber-reinforced cementitious composites based on slurry-infiltrated fiber concrete (SIFCON-based HPFRCC), which maximizes the steel-fiber volume fraction and uses high-strength mortar to increase resistance to loads, such as explosion and impact, with a very short acting time. For major experimental variables, three levels of fiber aspect ratio and five levels of fiber volume fraction between 6.0% and 8.0% were considered, and the flexural strength and toughness characteristics were analyzed according to these variables. Furthermore, three levels of the aspect ratio of used steel fibers were considered. The highest flexural strength of 65.0 MPa was shown at the fiber aspect ratio of 80 and the fiber volume fraction of 7.0%, and the flexural strength and toughness increased proportionally to the fiber volume fraction. The test results according to fiber aspect ratio and fiber volume fraction revealed that after the initial crack, the load of the SIFCON-based HPFRCC continuously increased because of the high fiber volume fraction. In addition, sufficient residual strength was achieved after the maximum strength; this achievement will bring about positive effects on the brittle fracture of structures when an unexpected load, such as explosion or impact, is applied.

Keywords

Acknowledgement

Supported by : Korea government and Korea Agency for Infrastructure Technology Advancement (KAIA), Kangwon National University

References

  1. ASTM C 1609 (2007), Standard Test Method for Flexural Performance of Fiber-Reinforced Concrete (Using Beam with Third-Point Loading, American Society for Testing and Materials (ASTM).
  2. Banthia, N. and Sappakittipakorn, M. (2007), "Toughness enhancement in the steel fiber reinforced concrete through fibers hybridization", Cement Concrete Res., 37(9), 1366-1372. https://doi.org/10.1016/j.cemconres.2007.05.005
  3. Park, C., Kim, Y., Choi, E. and Kim, S. (2016), "Fundamental properties and mechanical characteristics of high performance cement composite with steel fibers under high temperature", J. Struct. Integr. Mainten., 1(4), 189-196. https://doi.org/10.1080/24705314.2016.1240528
  4. Ku, D.O., Kim, S.D., Kim, H.S. and Choi, K.K. (2014), "Flexural performance characteristics of amorphous steel fiber-reinforced concrete", J. Kor. Concrete Inst., 26(4), 483-489. https://doi.org/10.4334/JKCI.2014.26.4.483
  5. Kim, S.W., Jeon, S.P., Shin, S.M., Cho, H.M. and Park, C.W. (2014), "Evaluation on filling performance of high flow slurry with respect to quantity of fine aggregate", Proceedings of the Korea Institute for Structural Maintenance and Inspection, 18(2), 407-409.
  6. Metha, P.K. and Monreiro, P.J. (2006), Concrete: Microstructure, Properties and Materials, 3rd Edition, McGraw-Hill, Inc., New York.
  7. Naaman, A.E. (2002), "Toughness, ductility, surface energy and deflection-hardening FRC composites", Proceedings of the JCI International Workshop on Ductile Fiber-Reinforced Cementitious Composites (DRFCC)-Application and Evaluation (DFRCC-2002), 33-57.
  8. Kim, S.W., Park, C.W., Kim, S.W., Cho, H.M., Jeon, S.P. and Ju, M.K. (2014), "Optimum mix proportions of in-fill slurry for high performance steel fiber reinforced cementitious composite", J. Kor. Recycl. Constr. Res. Inst., 2(3), 196-201. https://doi.org/10.14190/JRCR.2014.2.3.196
  9. Kim, S.W., Cho, H.M., Lee, H.Y. and Park, C.W. (2015), "Flexural performance characteristics of high performance slurry infiltrated fiber reinforced cementitious composite according to volume fraction", J. Kor. Inst. Struct. Mainten. Inspect., 19(4), 109-115. https://doi.org/10.11112/JKSMI.2015.19.4.109
  10. Kim, S. and Park, C. (2016), "Flexural behavior of high-volume steel fiber cementitious composite externally reinforced with basalt FRP sheet", J. Eng., 2016, 1-9.
  11. Kang, S.T. (2013), "Bond strength of steel fiber incorporated in ultra high performance fiber-reinforced concrete", J. Kor. Concrete Inst., 25(5), 547-554. https://doi.org/10.4334/JKCI.2013.25.5.547
  12. Lee, Y.O. and Yun, H.D. (2010), "Effects of expansive admixture on the mechanical properties of strain-hardening cement composite (SHCC)", J. Kor. Concrete Inst., 22(5), 617-624. https://doi.org/10.4334/JKCI.2010.22.5.617

Cited by

  1. Influence of the Amount of Steel Fibers on Fracture Energy and Drying Shrinkage of HPFRCC vol.2020, pp.None, 2020, https://doi.org/10.1155/2020/8459145