• Journal of environmental and Sanitary engineering
• /
• v.24 no.2
• /
• pp.1-8
• /
• 2009

This study was conducted at a Terminal, a Parking Lot, an Underground shopping center, a Funeral hall and a Hospital waiting room of Cheon An area in August 2008 to examine the concentration level of HCHO(formaldehyde). The concentration level of the remodeled sites were $39.4\;{\pm}\;12.0\;{\mu}g/m^3$ in the terminal, $32.7\;{\pm}\;7.3\;{\mu}g/m^3$ in the parking, and $97.8\;{\pm}\;29.4\;{\mu}g/m^3$ in the underground shopping center. The underground shopping center had the highest level and followed by the terminal and the parking. On the contrary, the site remodeling had the level of $17.7\;{\pm}\;12.4\;{\mu}g/m^3$ in the funeral hall and $17.9\;{\pm}\;0.6\;{\mu}g/m^3$ in the hospital waiting room. The funeral hall had highest level than that of the hospital waiting room. Both the remodeled sites and the not remodeled site had concentration level of HCHO below the standard level, but it was higher in the remodeled sites. There were no relations among the HCHO, the temperature and the humidity in facilities of Cheon An area.

• Journal of Institute of Convergence Technology
• /
• v.5 no.1
• /
• pp.13-17
• /
• 2015

In wafer level molding progress, the thermal releasing failure phenomenon is shown up as the important problem. This phenomenon can cause the problem including the warpage, crack of the molded wafer. The thermal releasing failure is due to the insufficiency of adhesion strength degradation of the molding tape. To solve this problem, we studied experimental method increasing the release property of the molding tape through the plasma surface treatment on the wafer substrate. In this research, the vacuum plasma treatment system is used for release property improvement of the molding tape and controls the operating condition of the hydrophilic($O_2$, 100kW, 10min) and hydrophobic($C_2F_6$, 200kW, 10min). In order to perform the peeling test for measuring the releasing force precisely, we remodel the micro scale material property evaluation system developed by Korea institute of industrial technology. In case of hydrophilic surface treatment on the wafer substrate, we can figure out the releasing property of molding tape increase. In order to grasp the effect that it reaches to the release property increase when repeating the hydrophilic treatment, we make an experiment with twice treatment and get the result to increase about 12%. We find out the hydrophilic surface treatment method using plasma can improve releasing property of molding tape in the wafer level molding process.

• Korean Institute of Interior Design Journal
• /
• v.25 no.4
• /
• pp.147-155
• /
• 2016

In order to ensure a certain level of the quality of design, standardized evaluation indicators are being used as an objective criterion. Even though the evaluation indicators are quantifiable, limitations such as inefficiency and inconsistency caused by manual task in the evaluation process still have been found. BIM (Building Information Modeling) technology that is commonly adopted in architectural design process provides an environment which enables us to figure out a building model to be interpreted quantitatively with the basis of the building information model. It supports quantitative, consistent, accurate and quick evaluations so as to improve quality of design even in the initial design phase. This paper aims to establish BIM-enabled quantitative indicators and an evaluation framework to analyze building circulation even in early phase of design. The indicators are composed of 4 types (relative distance, accessibility, simplicity, pedestrian friendliness) and 7 sub-types. The evaluation framework is the process to derive Parameterized Path Value (PPV) as weighting on each indicator. For demonstrating the scalability of the suggested evaluation indicators and the framework, the authors implemented an evaluation tool and a case study has been carried out by using an actual building remodel project.

• International Journal of Highway Engineering
• /
• v.19 no.6
• /
• pp.155-164
• /
• 2017

PURPOSES : Owing to the growth of income and socio-economic levels, demands from road users have diversified. Accordingly, new road policies are being actively sought. The metropolitan city government of Busan has been focused on constructing and expanding roads to accommodate the increasing traffic demand. Given the increase in functional characteristics, we need to re-evaluate the hierarchy and function of roads, and specifically remodel the road planning and operations that fit into their functions. METHODS : First, this study focuses on introducing the minimum condition required to redefine the hierarchy of the roads. Second, the authors propose a new model that identifies the impact level of road hierarchy adopting discriminated analysis technique. RESULTS : Authors suggest that we redefine the hierarchy of roads in the central business distinct in Busan, and specifically the arterial roads in Busan, namely, Joonang-daero and Gaya-ro. These roads need to be reequipped with cross walks, a lower speed limit, and exclusive bus lanes to improve their accessibility. CONCLUSIONS : The authors found that the sub-arterial and collector roads have been subjected to excessive loads, owing to inappropriate functions being assigned to the main arterial road. Moreover, given that through traffic is concentrated on the sub-arterial and collector roads, over-speeding and other safety issues are consequently created.

• 한국IT서비스학회:학술대회논문집
• /
• 2009.05a
• /
• pp.270-276
• /
• 2009

This paper outlines opportunities and challenges in the Implementation of BPEL based WFMS(Work Flow Management System) for the MES(Manufacturing Execution Systems) level in semiconductor manufacturing. At present, the most MES that are composed of several hundreds of applications in semiconductor wafer fabrication shop have the same problems as others about flexibility and adaptability. When a plant has to produce new product mix, remodel the manufacturing execution process, or replace obsolete equipments, the principal road blocks for responding to new manufacturing environment are inflexible communication infrastructure among the manufacturing process components and the difficulty in porting existing application software to new configurations. In this paper, the issues about BPEL standard, used for the flexibility of Workflow Management System, are presented. We introduce the integrated development framework named nanoFlow which is optimized for developing the BPEL based WFMS application for automated manufacturing system. We describe a WFMS implemented with using nanoFlow framework, review and evaluate the system in terms of flexibility and adaptability.

• Molecules and Cells
• /
• v.22 no.3
• /
• pp.262-268
• /
• 2006

During endometrial differentiation the extracellular matrix (ECM) changes dramatically to prepare for implantation of the embryo. However, the genes regulating the ECM build-up in the uterine endometrium during early pregnancy are not well known. Using the PCR-select cDNA subtraction method, dermatopontin was identified in the uterus of a pregnant mouse on day 4 of gestation. Dermatopontin mRNA increased dramatically on day 3, and was at its highest level at the time of implantation. Administration of RU 486 significantly inhibited mRNA expression by day 4 of gestation, but ICI 182,780 did not. Progesterone markedly induced dermatopontin expression in ovariectomized uteri within 4 h of administration, whereas estrogen had little effect. In silico analysis revealed progesterone receptor binding sites in the dermatopontin promoter region. Decidualization did not induce expression of dermatopontin; instead dermatopontin mRNA became strongly localized at the interimplantation site. In situ hybridization revealed that expression gradually decreased in the luminal epithelial cells as pregnancy progressed, whereas it increased in the stromal cells. The pattern of localization and the changes of intensity of dermatopontin mRNA coincided with those of collagen. Collectively, these results strongly suggest that dermatopontin expression is steroid-dependent. They also suggest that, at the time of implantation, dermatopontin expression is primarily regulated spatio-temporally by progesterone via progesterone receptors, and is modulated by the decidual response during implantation. Dermatopontin may be one of the regulators used to remodel the uterine ECM for pregnancy.

• Journal of the Korean Institute of Rural Architecture
• /
• v.18 no.3
• /
• pp.17-24
• /
• 2016

The aim of this study is to build an architectural landscaping design ways of vulnerable community in rural area. I surveyed scenery structures, public buildings and single home forms, and fence types of house in twelve villages which have undertaken improving environment of rural community in four provinces. They all have an inferior surroundings to live in rural village, because they were isolated from the city, located on the mountain or island, and made a living under the slate materials of roof. The central government has been driving to reform the conditions with local office, so that they may increase their living qualities and village environment to get to the general level of rural area. There are three results of this study as follows: First, the scenery of the village surveyed has a remarkable views of locality and hierarchy of layers between field and mountain, which is very identified as a typical image of Korean rural topology. Second, the public buildings and single homes and outside wall of houses were personally designed or reformed as a various types like a flat slab style and different architectural structure, because they followed only to keep the architectural code rather than to make a harmony with other traditional style buildings. When they have to remodel it again through SaethulMaul project, they are needed to consider of both architectural code and design guideline for the local landscape design image. Third, to make a different landscape view of each village and improve housing conditions, it should be taken a people participation design way.

• The Journal of the Korea Contents Association
• /
• v.21 no.8
• /
• pp.294-304
• /
• 2021

Medical institutions remodel existing hospital buildings rather than construct buildings to satisfy patient satisfaction and enhance competitiveness with other medical institutions. Medical institution remodeling is gradually increasing due to enhanced laws and systems to improve the quality of medical services and the level of patient safety. However, prior studies were discussed only within a limited range, including architectural elements, about medical institution remodeling. Therefore, this study aims to provide basic data to medical institutions planning future remodeling by examining the legal issues of medical institution remodeling in various ways. Medical institution remodeling extends the construction period due to restrictions on construction conditions, and causes damage such as noise and dust to patients. So it is necessary to prevent damage to patients in advance and to support appropriate remodeling of medical institutions. Therefore, it is necessary to prepare an Act on promotion of and support for remodeling of medical institutions. In addition, medical institutions should prepare a checklist for voluntary compliance with construction standards, preventive measures and post-improvement measures, and measures for infection and radiation exposure in hospitals.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.43 no.4 s.310
• /
• pp.46-54
• /
• 2006

Recently, the important of a personal identification is increasing according to expansion using each on-line commercial transaction and personal ID-card. Although a personal ID-card embedded RFID(Radio Frequency Identification) tag is gradually increased, the way for a person's identification is deficiency. So we need automatic methods. Because RFID tag is vary small storage capacity of memory, it needs effective feature extraction method to store personal biometrics information. We need new recognition method to compare each feature. In this paper, we studied the face verification system using Hippocampal neuron modeling algorithm which can remodel the hippocampal neuron as a principle of a man's brain in engineering, then it can learn the feature vector of the face images very fast. and construct the optimized feature each image. The system is composed of two parts mainly. One is feature extraction using NMF(Non-negative Matrix Factorization) and LDA(Linear Discriminants Analysis) mixture algorithm and the other is hippocampal neuron modeling and recognition simulation experiments confirm the each recognition rate, that are face changes, pose changes and low-level quality image. The results of experiments, we can compare a feature extraction and learning method proposed in this paper of any other methods, and we can confirm that the proposed method is superior to the existing method.

• Journal of the Korean Society for Library and Information Science
• /
• v.53 no.2
• /
• pp.91-116
• /
• 2019

This study conducted a demand analysis for the operation and management of closed schools, the direction of future use of closed schools, and the utilization of closed schools, among local residents expected to play a key role in the successful use of closed libraries. According to the study, residents in areas where schools actually occur may actively consider the use of closed schools when they are lacking in the number of libraries in the region or when they hope to remodel their schools as libraries, given that they are positive about future use of closed schools and that remodeling them is more economical in terms of cost than building new libraries. The current awareness of the use and operation of closed schools remains at a normal level, so it is deemed necessary to improve the direction of the promotion, operation and recycling of closed schools in the order of promotion, operation and physical aspects by grouping obstacles to the operation and management of closed schools. In addition, the current status of cultural facilities and the demands of local residents are met in terms of the types of use of closed school facilities, and it means that closed schools can be used in a relatively easy-to-access location based on their location, while libraries can be used as a space for cultural facilities that are different from the existing public libraries, exhibition halls, and eco-friendly libraries.