• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.8
• /
• pp.921-926
• /
• 2015

For the over-heat protection purpose in power strip devices, over-current detection/protection circuits, such as bimetal, switching circuit, and microprocessor-based relay circuit, have been widely setup in high-end products. Most of these circuits are connected to the power line in parallel and, thus, they are sensitive to the line voltage and current distortion. Moreover, these protection circuits are often costly and, therefore, it is hard to meet the commercial requirements. A low-cost over-current detection circuit with the contactless current transducer is designed and tested in this paper. The detection circuit is galvanically isolated from the power line and, thus, less sensitive to the line voltage distortion. The experimental results show that the proposed circuit accurately operates despite of its simple structure and low-cost electronic parts.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2002.11a
• /
• pp.281-286
• /
• 2002

An existent hoist drive system is using each different drive equipment in control of Hoisting, traveling(T/L), traversing(T/S) driving, so there are much energy losses because of excessive weight. Also, power circuits are using relay contact, so working environment are frequent secession accident etc.. by shock on unfavorable condition, and there is danger of safety accident, maintenance has frequent problem and so on. To solve these problem, it is integrated each driving power supply in drive system for hoist control and drive, utility power supply etc.. by single device in this research. The power circuit is consisted of non-contact circuit applying to bidirectional voltage controller circuit using thyristor that is power semiconductor switching device

• Journal of Power Electronics
• /
• v.17 no.5
• /
• pp.1372-1381
• /
• 2017

This paper presents a high-side switch driver IC capable of improving the current sensing accuracy and providing reverse battery protection. Power semiconductor switches used to replace relay switches are encumbered by two disadvantages: they are prone to current sensing errors and they require additional external protection circuits for reverse battery protection. The proposed IC integrates a gate driver and current sensing blocks, thus compensating for these two disadvantages with a single IC. A p-sub-based 90-V $0.13-{\mu}m$ bipolar-CMOS-DMOS (BCD) process is used for the design and fabrication of the proposed IC. The current sensing accuracy (error ${\leq}{\pm}5%$ in the range of 0.1 A-6.5 A) and the reverse battery protection features of the proposed IC were experimentally tested and verified.

• Proceedings of the KSR Conference
• /
• 2000.05a
• /
• pp.261-268
• /
• 2000

The purpose of interlocking system was to prevent the route for a train being set up and its protecting signal cleared if there was already another, conflicting route set up and the protecting signal for that route cleared. Recently, the computer based control systems instead of conventional relays circuitry are widely used to industrial systems, therefore, interlocking system are rapidly changing from relay interlocking system to computer controlled interlocking system that control requirements of interlocking at junctions using electronic circuits. However, the reliability of interlocking logic for those systems are harder to demonstrate than in traditional relays circuitry because the faults or errors can not be analyzed and predicted to those systems, In this paper, by examine checking technique of computer controlled interlocking system, we will to acquire interlocking inspection algorithm and method for computer controlled interlocking system

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.9
• /
• pp.1493-1496
• /
• 2016

This paper proposes a system for reducing the standby power consumption in using the consumer electronic devices such as a television, a home theater, a set-top box, or a DVD player. The system is consisted of a flyback converter, monitoring circuits, a relay and a micro-processor. The proposed system can reduce the standby power consumption by disconnecting the AC input and the consumer devices can be turned on with a remote control. The proposed standby power system consumes the low power to receive the infrared signal from the remote controller. Furthermore, a electronic double layer capacitor is used to store the energy with high efficiency. The proposed power system can operate the 플라이백 converter to charge the electronic double layer capacitor and connect the AC input to the consumer electronic devices. The proposed power circuit can reduce the standby power consumption in AV devices without increasing the cost. The prototype is implemented to verify the system with the commercialized products.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.5
• /
• pp.1129-1133
• /
• 2004

The MIC-NET of 3,010 circuits to process on-line business on post, insurance, finance, electromagnetic wave, and so forth has the problems on spending of bandwidth for the lack of flexibility of leased-line service band. In this paper, it is suggested to establish the efficient 3 steps conversion plan through analysis and comparison with economical efficiency on MIC-NET. The promoting policy proposed in this paper, both MIC and local post office will raise image as financial institute and provide high level service with reliability and security as distinguished government organization.

• Proceedings of the KIEE Conference
• /
• 1987.11a
• /
• pp.454-456
• /
• 1987

A more specialized area of transient evaluations is transmission line fault-detecting and protection system. During the first cycle or two following a power system fault, a high-speed protective relay is expected to make a decision as to the severity or location of the fault, usually based on 60 Hz information, i.e. the phase and magnitude of 60 Hz voltage or current signals. It is precisely at this time however that the signal is badly corrupted by noise, in the form of a de offset or frequencies above 50 Hz. One of several possible sources of transients in protection measuring signals is in the primary system for which protection is required in its response to the impact of short circuit fault on-set. Other sources are in the primary voltage and current transducers from which protection signals are derived, and, often of particular importance, in the interface circuits between the transducer secondaries and the comparator and measuring elements of the protection system. However, the noise signals that will be described in this paper are due to the main power system only and do not include errors due to current or voltage transducers.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.2
• /
• pp.131-137
• /
• 2005

Protective relays provide important features to electrical power systems for protecting against faults and consequent short circuits. This research presents a novel VLSI design of the digital protective relay, which overcomes today's uP/DSP-based relays. This design features good cancellation of DC/k-th harmonic components, noticeable not performance and flexible Protection behavior in the minimized core area The proposed design was successfully implemented by a FPGA(Field Programmable Gate Array) device and can concurrently process over 16KSPS at less $0.03[\%]$ error rate.

• Proceedings of the KIEE Conference
• /
• 2001.10a
• /
• pp.271-274
• /
• 2001

The purpose of interlocking system was to prevent the route for a train being set up and its protecting signal cleared if there was already another, conflicting route set up and the protecting signal for that route cleared. Recently, the computer based control systems instead of conventional relays circuitry are widely used to industrial systems, therefore, interlocking system are rapidly changing from relay interlocking system to Electronic Interlocking System(EIS) that control requirements of interlocking at junctions using electronic circuits. In this paper, by examine checking technique of EIS, we will to acquire interlocking inspection algorithm and method for EIS and to develope inspection system for EIS. By using inspection system we obtain every advantage. It has the functions for test data generation and automatic test execution, and it can operate on personal computer. Time and cost for test work can be reduced to more of those now required by using this developed inspection system.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.53 no.2
• /
• pp.70-76
• /
• 2004

The purpose of interlocking system in railway is to prevent the route for a train being set up and its protecting signal cleared if there were already another, conflicting route set up and the protecting signal for that route cleared. Recently, conventional relays circuitry in industrial field is replaced to computer-based control systems according to the advance of computer and communication technology. Therefore, interlocking systems in railway field are rapidly changing from existing relay-based interlocking system to computer-based electronic ones that executes the vital interlocking logic to assure the safety train routes at trackside signaling equipment room using electronic circuits. So it is very important to verify the performance of developed electronic interlocking system by plentiful laboratory testing before actually application in the railway system. However the laboratory testing in the present state of railway signaling is preformed individually by manual, so very much test time and cost are required. To solve these problems, we are developed the simulator for automatic interlocking inspection in this research. This simulator is able to operate on general personal computer and has following beneficial functions : automatic test sheet generation for inspection, automatic inspection execution and et al. The experiments are executed to test the feasibility of the developed simulator the experimental results have good agreements with the anticipated ones.