• Advances in concrete construction
• /
• 제14권2호
• /
• pp.139-151
• /
• 2022

Filling materials poured into precast member joint are subjected to restraint stress by the precast member and joint reinforcement. The induced stress will likely cause cracks at early ages and performance degradation of the entire structure. To prevent these issues and design reasonable joints, it is very important to analyze and evaluate the restrained shrinkage cracks of filling materials at various restraint conditions. In this study, a new time zero-that defines the shrinkage development time of a filling material-is proposed to calculate the accurate amount of shrinkage. The tensile stresses and strengths at different ages were compared through the ring test (AASHTO PP34) to evaluate the crack potential of the restrained filling materials at various restraint conditions. The mixture which contained an expansive additive and a shrinkage reducing agent exhibited high resistance to shrinkage cracking owing to the high-drying shrinkage compensation effect. The high-performance, fiber-reinforced cement composite, and ultra-high-performance, fiber-reinforced cement composite yielded very high resistance to shrinkage and cracking owing to the pull-out property of steel fibers. To this end, multiple nonlinear regression analyses were conducted based on the test results. Accordingly, a modified tensile stress equation that considered both the geometric shape of the specimen and the intrinsic properties of the material is proposed.

• 한국구조물진단유지관리공학회 논문집
• /
• 제25권6호
• /
• pp.245-253
• /
• 2021

우리나라 노후화 교량 중 많은 부분을 차지하는 RC 슬래브 교량은 대부분이 교량 안전 관리 및 유지관리의 대상인 1, 2종 교량에 포함되지 않는다. 또한 고속도로 교량에서 가장 높은 손상율을 차지하는 부속시설은 신축이음과 교량 받침부이다. 특히, 신축이음부를 통한 누수는 콘크리트 교량의 열화를 유발하고 균열 및 철근부 노출 등의 원인이 된다. 따라서 본 연구에서는 RC 슬래브교의 신축이음부 유간 밀착 손상이 바닥판 응답에 미치는 영향을 분석하였다. 양단 신축이음의 유간이 밀착된 경우 바닥판의 교축방향 변위가 발생되지 못해, 양쪽 단부 콘크리트에서 균열이 발생하였다. 또한, 응답 결과를 바탕으로 손상시나리오 별 신축이음부의 교축방향 변위와 바닥판 양단 콘크리트 응력과의 상관관계를 분석하고, 손상발생이 교량 거동에 미치는 영향을 파악하였다. 신축이음 장치 양면손상이 발생한 경우 변위와 응력과의 상관관계는 차량이 모든 차선을 지날 때 0.18로 낮은 상관성을 보였다. 무손상 상태와 비교했을 때도 바닥판 처짐은 차량이 지나는 동안 0.34~0.53, 차량이 지나간 후 0.17~0.43으로 낮은 상관성을 보였다. 이는 단부 콘크리트의 균열 발생으로 바닥판 전체 거동에 변화가 생긴 것을 의미한다. 따라서 바닥판 응답 데이터 기반 상관관계 분석과 이를 활용한 데이터 기반의 손상탐지가 가능하며, 이를 통해 바닥판 손상 및 열화의 원인이 되는 신축이음부의 조기 보수 및 보강, 사전관리에 기여하여 많은 도움이 될 것으로 기대된다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제21권2호
• /
• pp.95-102
• /
• 2017

본 연구는 철근상세(대각선 및 수평 철근상세)가 실규모 연결보의 구조성능에 미치는 영향을 평가하기 위하여 실시되었다. 연결보의 시공성 및 경제성을 향상시키기 위하여 고강도 철근(SD500 및 SD600)을 사용하였다. 반복하중이 작용하는 동안 연결보의 순경간(양쪽 전 단벽 사이의 간격)을 유지하기 위하여 강체 프레임 및 링크조인트를 설치하였다. 실험결과 대각선 철근상세을 적용한 연결보가 수평 철근상세 연결보에 비해 높은 연성을 나타내었다. AC1318-14 기준은 대각선 철근상세의 연결보 설계에는 적용이 가능할 것으로 판단되나, 수평 철근상세 연결보의 최대내력은 과대평가하는 것으로 나타났다. ASCE 41-13에서 제시된 연결보의 유효강성은 대각선 및 수평 철근상세를 적용한 연결보의 실험결과를 과대평가하고 있는 것으로 판단된다.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2000년도 춘계 학술발표회 논문집 Proceedings of EESK Conference-Spring
• /
• pp.283-289
• /
• 2000

The panel shear and bearing strengths determining the seismic resistance of reinforced concrete column-to-steel beam connections are predicted by various methods for four previously tested exterior beam-column joints. The analytical approach to model the joint deformation is also examined. Several analyses incorporating the deformations of panel shear and bearing in the joint are demonstrated using a analyses incorporating the deformations of panel shear and bearing in the joint are demonstrated using a fairly simple connection model in the commercial packages such as Drain2dx and IDARC. The strength prediction results indicated that the ASCE method with the modifcation of the comprssion strut contribution is th most accurate. It is also considered that the analytical model presented including the joint deformation can be used for the overall analysis

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2011년도 정기 학술대회
• /
• pp.10-13
• /
• 2011

내진설계의 기본 개념은 보를 기둥보다 약하게 설계하여 보에 소성힌지를 발생시켜 구조물 전체의 큰 변형을 방지하는 것이다. ACI 352R-02에서는 지역의 지진특성에 따라서 접합부의 상세 설계법을 구분하여 적용한다. 하지만 보와 접합부의 내력 차이가 상대적으로 작게 설계된 구조물의 경우 탄성 범위를 유지해야 하는 경우의 접합부에도 파괴가 발생할 가능성이 있다. 횡하중이 작용할 때 접합부 내부는 전단력의 지배를 받게 되고, 전단내력과 부착내력에 따라서 파괴모드가 결정된다. 본 논문에서는 양방향 반복하중이 작용하는 10개의 보-기둥 접합부를 통해서 접합부와 인접보의 전단내력 차이에 따라서 발생하는 파괴모드를 관찰하고 접합부 내의 전단내력 및 부착내력의 감소로 인해 발생하는 부재의 연성에 대해서 관찰하였다.

• Steel and Composite Structures
• /
• 제8권4호
• /
• pp.329-342
• /
• 2008

The strengthening of reinforced concrete (RC) columns by steel angles and strips (steel cage) is one of various techniques available to increase ultimate column load. Different authors have shown the influence of the beam-column joint on the behaviour of columns strengthened by steel cages. This paper presents an experimental study carried out at the Universidad Polit$\acute{e}$cnica de Valencia with the aim of analysing two different techniques to solve the strengthening close to the joint and the influence on the behaviour of RC columns strengthened steel cages. The ultimate loads obtained in the laboratory tests for these two techniques are compared to that specified by Eurocode 4.

• Structural Engineering and Mechanics
• /
• 제23권2호
• /
• pp.129-145
• /
• 2006

This paper provides an insight into the response of non-seismic reinforced concrete (RC) building frames to excitations of different frequencies through experimental investigation. The results of cyclic loading tests of six full-scale RC beam-column sub-assemblies are presented. The tested specimens did not have any transverse reinforcement inside the joint core, and they were subjected to quasi-static and dynamic loading with frequencies as high as 20 Hz. Some important differences between the cyclic responses of non-seismic and ductile RC frames are highlighted. The effect of excitation frequency on the behavior of non-seismic joints is also discussed. In the quasi-static tests, shear deformation of the joint panel accounted for more than 50% of the applied story drift. The test results also showed that higher-frequency excitations are less detrimental than quasi-static cyclic loads, and non-seismic frames can withstand a higher load and a larger deformation when they are applied faster.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2003년도 추계 학술발표회논문집
• /
• pp.133-140
• /
• 2003

The objective of this study is to clarify the seismic capacity and the characteristics in the hysteretic behavior of RC structures with non-seismic detailing. Interior and exterior beam-column subassemblages were selected from a ten-story RC building and six 1/3-scale specimens were constructed with three variables; (1) with and without slab, (2) with and without hoop bars in the Joint region, (3) upward and downward direction of anchorage for the bottom bar in beams of exterior beam-column subassemblage. The test results have shown; (1) in case of interior beam-column subassemblage, there is no almost difference between nonseismic and seismic details in the strength and ductility capacity; (2) the Korean practice of anchorage (downward and 25 $d_{b}$ anchorage length) in the exterior Joint caused the 10％~20％ reduction of strength and 27％ reduction of ductility iii comparison with tile case of seismic details; and the existence of hoop bars in the joint region shows no effect in shear strain.n.

• Earthquakes and Structures
• /
• 제22권5호
• /
• pp.475-485
• /
• 2022

This paper presents a comparative experimental study on structural behavior of the interlocking masonry walls under in-plane cyclic loading. The main purpose of this study is to increase lateral load-bearing capacities of masonry walls by using interlocking units. The interlocking units were designed by considering failure modes of masonry walls and produced using lightweight foamed concrete. To this end, three masonry walls which are hollow, fully grouted, and reinforced were constructed with interlocking units. Also, a traditional masonry brick wall was built for comparison reasons. The walls were tested under in-plane cyclic loading. Then, structural parameters of the walls such as lateral load bearing and total energy dissipation capacities, ductility, stiffness degradation as well as failure modes obtained from the tests were compared with each other. The results have shown that the walls with the interlocking units have better structural performance than traditional masonry brick walls and they may be used in the construction of low-rise masonry structures in rural areas to improve in-plane structural performance.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 봄 학술논문 발표대회
• /
• pp.319-320
• /
• 2023

In a reinforced concrete structure, coupler construction is easier to install than jointing or welding reinforcing bars, so it is possible to work by one person. When constructing a reinforcing bar coupler, the coupler construction method must be different for each member that receives a large tensile force or a member that receives a small tensile strength. Various coupler products are used in the global construction market, and the quality, performance, and cost of reinforcing bar joints vary from product to product. This study compares and analyzes the quality and cost of representative rebar couplers according to the requirements using the quality house of QFD-HOQ. The case study presents a quality and cost improvements strategy through QFD-HOQ analysis of rebar couplers.